Product ViewProduct Description
Features:
1. Dual power supply (two power supplies cannot be powered at the same time): Power supply 1, DC 6.5-25V; Power supply 2, DC 5V.
2. Working current: (Normal Mode) standby current 41mA, working current 83mA; (Energy-Saving mode) Standby current 7mA, working current 44mA.
3. There are three input control port: forward control(FWD), reverse control(REV), and stop control(STOP).
3. Two input trigger modes, Low-Pulse trigger mode, Low-Level trigger mode.
4. Delay time: 0.1-999.9 seconds, 1-9999 seconds, 1-9999 minutes.
Cycle times: no cycle, 2-99 cycles, always cycle.
5. Three indicators: forward indicator(F LED), reverse indicator(R LED), stop indicator(S LED).
6. Relay load current, recommended less than 5A.
7. This is a multi-function DC/AC motor forward and reverse controller with multiple control modes. Many control functions can be derived through reasonable settings.
Port:
DC 5.5 Female: Power supply 1, DC 5V power supply
VIN: Power 2 positive, DC 6.5-25V power supply
GND: Power supply 2 negative
FWD: Forward input control (partial Function-Mode is invalid)
REV: Reverse input control (partial Function-Mode is invalid)
STOP: Stop input control (partial Function-Mode is invalid)
M+: Motor positive
M-: Motor negative
P+: Positive terminal for motor power supply
P-: Negativeterminal for motor power supply
Specification:
Power Supply: DC 6.5-25V, DC 5V
Working Current: 83mA
Standby Current: 41mA
Relay Load Current: <5A
Delay Time: 0.1-999.9 Seconds, 1-9999 Seconds, 1-9999 Minutes
Size: 8*5cm/3.2*2in
Weight: Approx. 51g/1.8oz
Trigger Mode:
1 Low Pulse Trigger (Falling Edge Trigger)
2 Low Level Trigger (Rising Edge Trigger)
Timer:
T1: Forward Timer
T2: Reverse Timer
T3: Stop Timer
Time Unit : 0.1 Second, 1 Second, 1 Minute
Relay Action:
Motor Forward: Relay 1 is ON, relay 2 is OFF, and the F LED indicator is flashing.
Motor Reverse: Relay 1 is OFF, relay 2 is ON, and the R LED indicator is flashing..
Motor Stop: Relay 1 is OFF, relay 2 is OFF, and the S LED indicator is flashing.
Factory Settings:
Press the \"++\" and \"--\" buttons simultaneously for 5 seconds.
Energy-saving mode:
Press and hold the \"OK\" button for 5 seconds to enter the \"Energy-saving mode\". Press and hold the \"OK\" button again for 5 seconds to exit the \"Energy-saving mode\". Energy saving mode just turns off the digital tube and LED indicator, and other functions are normal.
Function mode:
F-01
After power-on, the motor is forward T1 time; then the motor stops T3 time; then the motor reverse T2 time; so it is repeated Nx times. When the STOP port is triggered, the motor stops working immediately. (FWD, REV port is invalid)
F-02
This function is a F-01 variant. F-01 is run directly after power-on, but F-02 needs to trigger FWD or REV port to run.
F-11(Trigger Reversible 1)
Trigger the FWD port, the motor is forward T1 time, and automatically stops (in order to protect the motor, during the delay period, trigger the REV port to stop T3 time and then reverse T2 time, trigger FWD port to re-time T1).
Trigger the REV port, the motor is reverse T2 time, and automatically stops (in order to protect the motor, during the delay period, the FWD port is triggered to stop the T3 time and then the T1 time is forward, and the REV port is re-timed T2).
When the STOP port is triggered, the motor stops immediately, regardless of whether the motor is forward or reverse.
F-12(Trigger Reversible 2)
Trigger the FWD port, the motor is forward T1 time and stops automatically (during the delay period, except for triggering STOP port, the other ports are invalid).
Trigger the REV port, the motor is reverses T2 time, and automatically stops (during the delay period, except for triggering STOP port, the other ports are invalid).
When the STOP port is trigger, the motor stops immediately, regardless of whether the motor is forward or reverse.
F-21
When the FWD port is low level, the motor is forward, and after the FWD port is released, the motor stops.
When the REV port is low level, the motor is reversed, and after the REV port is released, the motor stops.
In this mode, the FWD and REV ports cannot be connected low level at the same time, and the STOP port is invalid.
F-22
When the FWD port is low level, the motor is forward, and after the FWD port is released, the motor stops.
When the REV port is low level, the motor is reversed, and after the REV port is released, the motor stops.
In this mode, the FWD and REV ports cannot be connected low level at the same time, triggering the STOP port, the motor stops immediately.
Parameter Setting:
There are three menus: Work Menu, Function Menu, Parameter Menu.
Note: When entering the \"Function Menu\" or \"Parameter Menu\", the module still works normally (countdown and the trigger is running normally). The set parameters are valid only after being powered on again.
1. Power on to enter the running state (Work Menu).
If the current function is F-01, then the motor direct run and the digital tube displays the countdown. F-01 is displayed after the operation is completed.
If the current function is other functions, such as F-11. Then the digital tube displays F-11. After the trigger, the digital tube displays the countdown. After the operation is completed, F-11 is displayed.
Functionmode
Digitaltubedisplay
Settingmethod
Function01
F1-01
Function02
F1-02
Function011
F1-11
Function012
F1-12
Function21
F1-21
Function22
F1-22
2. In the running state(Work Menu), short press the SET button to enter the \"Function Menu\" (Above table).
bit2
bit3-4
parameterdefinition
defaultparameter
1
-
00-99
04
2
-
00-99
00
3
-
00-99
02
4
-
00-99
00
5
-
00-99
01
6
-
00-99
00
7
-
01-03
01:0.1seconds
02:second
03:minute
timeunit
02
8
-
0-99
numberofcycles
1
9
-
01-02
01lowpulsetrigger
02lowleveltrigger
triggermode
01
Package List:
1 x Motor Controller Board
It is impossible to address issues if we do not know about them!Guarantee1. 12 months Manufacturer’s limited Warranty for defective items (excluding items damaged and/or misused after receipt). Accessories come with a 3-month warranty.
2. Defective items MUST BE reported and returned within the warranty period (and in the original packaging, if possible). You must tell us what the defect is and give us your order number. WE DO NOT REPAIR OR REPLACE ITEMS WITH AN
EXPIRED WARRANTY.
Return\\Refund1. You have 7 days to contact us and 30 days to return it from the date received. If the item is in your possession more than 7 days, it will be considered used and WE WILL NOT ISSUEA REFUND OR REPLACEMENT to you. There are NO EXCEPTIONS!
Shipping cost is bear by both seller and buyer in half.
2. All returned items MUST BE in the original packaging and you MUST PROVIDE us with the shipping tracking number, specific reason for the return, and your order ID.
3. We will refund YOUR FULL WINNING offer AMOUNT, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER BOTH Buyer and Seller cancel the transaction from aliexpress. OR, you may choose to have a replacement.
4. We will bear all the shipping cost if the product(s) is (are) not as advertised.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.