New fabricated steel center section, New 3\" O.D. axle tubes w/ 3/16\" wall thickness, Axle tubes are internally reinforced for additional strength, Performance 31-spline axle shafts, New Big Ford Toriono-style bearings, seals and HD retainers Speedway Fabricated Ford 9 Inch Rearend Axle Housing Kit, 60 In. Width Sku # 91046060 Mfr. Part # 91046060 Condition New Brand Speedway Motors Sold Kit Details
Looking for a budget-friendly, rock-solid foundation for your custom rear suspension? Look no further. Our fabricated steel Ford 9 inch axle housings feature all-new components for maximum durability. It’s an evolution of the rugged and reliable 9 inch Ford platform.
Designed with the Builder in Mind
This housing is pumpkin-centered with uniform-length axle tubes, side-to-side. So mounting suspension brackets, especially on triangulated 3-link and 4-link systems, is much easier. Unlike factory stamped housings, these fabricated plate-steel center sections provide a wide, flat surface for easy bracket attachment. Note that the pumpkin-centered design will offset the pinion yoke about 1\" to the passenger side.
Axle tubes are 3” O.D. with a 3/16” wall thickness. Heavy-wall tubes, along with a larger center section, significantly reduce distortion during welding of rear-link brackets or spring pads. Billet steel “New Big Ford” (Torino) style bearing ends are fixture-welded (3.150” O.D. bearing, with 2.50” axle flange offset).
Improved Design for Greater Durability
In addition to the heavy-duty bearing ends, the axle tubes are supported with bracing inside the large center housing. This reduces flex in the rear end housing, which is something you won’t find on stamped factory 9 inch housings. Plus, gears stay well-lubed and run cooler thanks to a large-capacity fabricated center (holds more gear oil than stamped housings). Axle is vented on the driver’s side.
Yet, with improved durability, our fabricated axle housing is on average 2 pounds lighter than stock style housings of the same size! Add your choice of axle shafts and third member (sold separately), and you are ready to roll. Equip your race car, hot rod or 4X4 with Ford 9 inch parts from Speedway Motors to ensure there are no weak links in your driveline combination.
Total wheel-to-wheel mounting surface width is 60\" (from hub-to-hub). The pumpkin is centered in the housing, which puts the pinion 1\" offset from center, requiring different length axle shafts. This 60\" housing includes one 30-5/8\" long axle and one 28-1/4\" long axle. This housing includes (8) T-bolts for the axle bearing retainer plates and (10) studs for the third member.
Forged Steel Axles
Our improved axle housings deserve equally strong axles to drive your street machine. Two custom cut Currie axles made of heat-treated 1541 forged alloy steel have the strength to handle the horsepower. Axles are 31-spline, include axle shafts, axle bearings, axle seals, and bearing retainers. Flanges are dual-drilled for both 5 on 4-1/2\" Ford/Mopar and 5 on 4-3/4\" GM wheel bolt patterns, and include two sizes of wheel studs (1/2\"-20 Ford/Mopar and 7/16\"-20 GM).
- Fabricated steel center section
- 3\" O.D. axle tubes with 3/16\" wall thickness
- Axle tubes are internally reinforced for additional strength, less flex
- Billet steel \"New Big Ford\" (Torino) style bearing ends
- Forged 1541 Steel axle, dual drilled for both 5 on 4-1/2\" Ford/Mopar and 5 on 4-3/4\" GM wheel bolt patterns.
- Accepts brake kits for 2.50\" axle shaft flange offset (from housing flange)
- Housing measures 55\" from flange-to-flange
- Assembled rearend measures 60\" from hub-to-hub (axle flange face-to-face)
- Includes one 30-5/8\" long axle and one 28-1/4\" long axle
- Improved housing design weighs approximately 2 lbs less than stock-style fabricated housings
- Centered pumpkin w/ 1\" offset pinion yoke for easy suspension mock-up
- Greater-than-stock capacity center section holds more gear oil and runs cooler
- Requires different length axle shafts, left/right
- Includes vent on driver side axle tube
- Includes studs for 3rd member and 3/8” T-bolts for bearing retainer plates
- 3rd Member retainer stud nuts and washers not included but available separately as # 919-0916 (see related components at right)
- 3rd member sold separately
Specs Sold in Quantity Kit MFG. Part # 91046060 Position Rear Overall Width 60" Axle Shafts Included Yes Axle Splines 31 Axle Type Semi-Floating Brakes Included No Third Member Included No Ring and Pinion Included Yes Wheel Studs Included Yes Wheel Stud Thread Size 1/2"-20 Wheel Bolt Pattern (in.) 5x4.5 in. | 5x4.75 in. Bearings Included Yes Seals Included Yes Differential Included No Material Type Steel Finish Natural Ring Gear Size 9 Inch Differential Type Limited Slip Tube O.D. 3" Housing Material Steel Hardware Included Yes Rotors Included No Rotor Diameter Not Included Housing Color Gray Cut to Fit No Standard Pinion Location Offset Pinion / Centered 3rd Member Bolt Pattern 5 on 4.5" | 4.75" Reviews I would buy this again for my next project Rated by Stephen White on May 27, 2021
Summary: It installed but not in use yet
Yes, I recommend this product.
9 inch rear end Rated by hgwayman on December 29, 2020
Summary: I like the product but did not come with the 4 3/4 studs for GM as it should have. they are still on back order.
Yes, I recommend this product.
Great quality Rated by Mike on October 30, 2020
Summary: Made in the USA. Great quality. Well worth the money. Great customer service.
Yes, I recommend this product.
Great Quality and freaky fast shipping...lol arrived early Rated by Ken on November 07, 2019
Summary: Still have a few things to get and finish up but no problems so far.
Yes, I recommend this product.
I would warn others of this issue. Rated by Evan on June 03, 2019
Summary: Following the purchase and installation of this axle, I ordered a disc brake conversion designed to fit this application. I needed to modify the register of the rotors, machine the hat larger, in order to allow them to fit over the axle flange.
Yes, I recommend this product.
Related Items / Suggested Parts Ford 9 Inch Posi Differential 3rd Member, 31 Spl, 3.50 Gear Ratio Speedway Ford 9 Inch Posi Traction 3rd Member Assembly, 31 Spl, 3.00 Tanks REFD Rear End Filler and Drain Kit Third Member Mounting Hardware, Ford 8 In/ 9 In Rear End Ford 9 Inch Limited Slip Posi Differential Third Members, Clutch Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake Caliper Budget Ford 9 Inch Rear End Disc Brake Conversion Kit Weld On Leaf Spring Pad, Perch, 3 Inch Axle Tube, Pair Speedway 8 & 9 Inch Ford Disc Brake Conversion Kit w/ E-Brake Ford 9 Inch Helical Posi Limited Slip Third Members | 28/31 Spline Universal Ford 9 Inch Rear-End Disc Brake Conversion Kit, Black Dot Braided Stainless Brake Hoses, GM/Ford, 7/16-20 Rear Tech Support We\'re here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through Messaging and a knowledgeable Speedway Motors team member will be happy to help. About Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 74 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.