HEAVY-DUTY CONSTRUCTION: Fabricated steel center section with 3-inch O.D. axle tubes and 3/16-inch wall thickness provides exceptional strength and rigidity for performance builds., INTERNAL REINFORCEMENT: Axle tubes feature internal bracing to reduce flex, distortion, and weld stress—ideal for custom 3-link or 4-link suspension setups., COMPATIBLE BEARING ENDS: Equipped with billet steel Torino-style bearing ends (3.150” O.D.) for “New Big Ford” housings, with HD retainers and seals for maximum durability and precise alignment., FORGED 31-SPLINE AXLES: Includes heat-treated 1541 forged alloy steel axles, dual-drilled for 5 on 4-1/2\" Ford/Mopar and 5 on 4-3/4\" GM bolt patterns, with both 1/2\"-20 and 7/16\"-20 studs., ENGINEERED PERFORMANCE: Centered pumpkin with 1\" pinion offset improves br Speedway Fabricated Ford 9 Inch Rearend Axle Housing Kit, 56 In. Width Sku # 91046056 Mfr. Part # 91046056 Condition New Brand Speedway Motors Sold Kit Details
Looking for a budget-friendly, rock-solid foundation for your custom rear suspension? Look no further. Our fabricated steel Ford 9 inch axle housings feature all-new components for maximum durability. It’s an evolution of the rugged and reliable 9 inch Ford platform.
Designed with the Builder in Mind
This housing is pumpkin-centered with uniform-length axle tubes, side-to-side. So mounting suspension brackets, especially on triangulated 3-link and 4-link systems, is much easier. Unlike factory stamped housings, these fabricated plate-steel center sections provide a wide, flat surface for easy bracket attachment. Note that the pumpkin-centered design will offset the pinion yoke about 1\" to the passenger side.
Axle tubes are 3” O.D. with a 3/16” wall thickness. Heavy-wall tubes, along with a larger center section, significantly reduce distortion during welding of rear-link brackets or spring pads. Billet steel “New Big Ford” (Torino) style bearing ends are fixture-welded (3.150” O.D. bearing, with 2.50” axle flange offset).
Improved Design for Greater Durability
In addition to the heavy-duty bearing ends, the axle tubes are supported with bracing inside the large center housing. This reduces flex in the rear end housing, which is something you won’t find on stamped factory 9 inch housings. Plus, gears stay well-lubed and run cooler thanks to a large-capacity fabricated center (holds more gear oil than stamped housings). Axle is vented on the driver’s side.
Yet, with improved durability, our fabricated axle housing is on average 2 pounds lighter than stock style housings of the same size! Add your choice of axle shafts and third member (sold separately), and you are ready to roll. Equip your race car, hot rod or 4X4 with Ford 9 inch parts from Speedway Motors to ensure there are no weak links in your driveline combination.
Total wheel-to-wheel mounting surface width is 56\" (from hub-to-hub). The pumpkin is centered in the housing, which puts the pinion 1\" offset from center, requiring different length axle shafts. This 56\" housing includes one 28-5/8\" long axle and one 26-3/8\" long axle. This housing includes (8) T-bolts for the axle bearing retainer plates and (10) studs for the third member.
Forged Steel Axles
Our improved axle housings deserve equally strong axles to drive your street machine. Two custom cut Currie axles made of heat-treated 1541 forged alloy steel have the strength to handle the horsepower. Axles are 31-spline, , axle bearings, axle seals, and bearing retainers. Flanges are dual-drilled for both 5 on 4-1/2\" Ford/Mopar and 5 on 4-3/4\" GM wheel bolt patterns, and include two sizes of wheel studs (1/2\"-20 Ford/Mopar and 7/16\"-20 GM).
- Fabricated steel center section
- 3\" O.D. axle tubes with 3/16\" wall thickness
- Axle tubes are internally reinforced for additional strength, less flex
- Billet steel \"New Big Ford\" (Torino) style bearing ends
- Forged 1541 Steel axle, dual drilled for both 5 on 4-1/2\" Ford/Mopar and 5 on 4-3/4\" GM wheel bolt patterns.
- Accepts brake kits for 2.50\" axle shaft flange offset (from housing flange)
- Housing measures 51\" from flange-to-flange
- Assembled rearend measures 56\" from hub-to-hub (axle flange face-to-face)
- Includes one 28-5/8\" long axle and one 26-3/8\" long axle
- Improved housing design weighs approximately 2 lbs less than stock-style fabricated housings
- Centered pumpkin w/ 1\" offset pinion yoke for easy suspension mock-up
- Greater-than-stock capacity center section holds more gear oil and runs cooler
- Requires different length axle shafts, left/right
- Includes vent on driver side axle tube
- Includes studs for 3rd member and 3/8” T-bolts for bearing retainer plates
- 3rd member sold separately
Specs Sold in Quantity Kit MFG. Part # 91046056 Position Rear Overall Width 56" Axle Shafts Included Yes Axle Splines 31 Axle Type Semi-Floating Brakes Included No Third Member Included No Ring and Pinion Included Yes Wheel Studs Included Yes Wheel Stud Thread Size 1/2"-20 Wheel Bolt Pattern (in.) 5x4.5 in. | 5x4.75 in. Bearings Included Yes Seals Included Yes Differential Included No Material Type Steel Finish Natural Ring Gear Size 9 Inch Differential Type Limited Slip Tube O.D. 3" Housing Material Steel Hardware Included Yes Rotors Included No Rotor Diameter Not Included Housing Color Gray Cut to Fit No Standard Pinion Location Offset Pinion / Centered 3rd Member Bolt Pattern 5 on 4.5" | 4.75" Reviews Great Product Rated by Axle on May 24, 2025
Summary: This was a great kit would definitely use again
Yes, I recommend this product.
9" ford rearend Rated by Rog 32 on June 02, 2024
Summary: Nice Quality
Yes, I recommend this product.
Great product great price Rated by Joe on February 04, 2023
Summary: The product is used on a1969 nova
Yes, I recommend this product.
Awesome custom width axle Rated by Brian on July 08, 2020
Summary: Going into a custom Shelby 427 Cobra. Should be plenty strong.
Yes, I recommend this product.
Perfect fit. Good quality Rated by Jerzjer on June 17, 2020
Summary: Fits perfect, good quality
Related Items / Suggested Parts Ford 9 Inch Posi Differential 3rd Member, 31 Spl, 3.50 Gear Ratio Speedway Ford 9 Inch Posi Traction 3rd Member Assembly, 31 Spl, 3.50 Speedway Ford 9 Inch Posi Traction 3rd Member Assembly, 31 Spl, 3.70 Tanks REFD Rear End Filler and Drain Kit Third Member Mounting Hardware, Ford 8 In/ 9 In Rear End Currie 9 Inch Ford Hot Rod Rear Axle Rearend Housing Kit Ford 9 Inch Limited Slip Posi Differential Third Members, Clutch Budget Ford 9 Inch Rear End Disc Brake Conversion Kit Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake Caliper Weld On Leaf Spring Pad, Perch, 3 Inch Axle Tube, Pair Universal Drive Shaft U-Bolts, 1-1/16 Inch Cap Ford 9 Inch Helical Posi Limited Slip Third Members | 28/31 Spline Tech Support We\'re here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through Messaging and a knowledgeable Speedway Motors team member will be happy to help. About Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 74 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.