Description:Sensing InpuuutVoltage 220 / 380 / 440 VAC, 1 phase2 wireDIP switch selectableFrequency 50 / 60 Hz, DIP switch selectablePower InputVoltage 100 ~ 300 VAC, 1 phase 2 wireOutputVoltage Max. 90 VDC @ 240 VAC inputCurrent Continuous 5AIntermittent 7A for 10 secResistance Min. 15 ohm Max. 100 ohmVoltage Regulation< ± 0.5% ( with 4% engine governing )Voltage Build-upResidual voltage at AVR terminal > 5 VACThermal Drift0.03% per °C change in AVR ambientExternal Volts Adjustmen± 7% with 1K ohm 1 watt trimmerEMI SuppressionInternal electromagnetic interference filteringUnit Power DissipationMax. 8 wattUnder Frequency Protection (Factory Setting)60 Hz system presets knee point at 55 Hz50 Hz system presets knee point at 45 HzSoft Sta...
LABLT AVR EA05A Automatic Voltage Regulator Controller For Generator Genset
Description:
Sensing Inpuuut
Voltage 220 / 380 / 440 VAC, 1 phase2 wire
DIP switch selectable
Frequency 50 / 60 Hz, DIP switch selectable
Power Input
Voltage 100 ~ 300 VAC, 1 phase 2 wire
Output
Voltage Max. 90 VDC @ 240 VAC input
Current Continuous 5A
Intermittent 7A for 10 sec
Resistance Min. 15 ohm Max. 100 ohm
Voltage Regulation
< ± 0.5% ( with 4% engine governing )
Voltage Build-up
Residual voltage at AVR terminal > 5 VAC
Thermal Drift
0.03% per °C change in AVR ambient
External Volts Adjustmen
± 7% with 1K ohm 1 watt trimmer
EMI Suppression
Internal electromagnetic interference filtering
Unit Power Dissipation
Max. 8 watt
Under Frequency Protection (Factory Setting)
60 Hz system presets knee point at 55 Hz
50 Hz system presets knee point at 45 Hz
Soft Start Ramp Time
3 sec.
Dimensions
101mm L * 69mm W * 47.5mm H
Weight
183g ± 2%
2. WIRING
When generator supply is over load, N phase will be different with the sharing load by 3 phases (load imbalance). Hence, the voltage from N phase to 3 phases (R.S.T.) will be altered. When the rated voltage of the traditional single input’s AVR is above 220V, it will increase the voltage drift rate by using N phase as the detective input. It will also cause the voltage imbalance.
EA05A can improve the above situation, and increase the generator’s rated voltage usage space,such as 380V, 440V. We can all detect by the “phase voltage”.
1. When the rated phase voltage of the generator is 220VAC, the input terminals B, C and sensing terminals A, C can join together (as show as figure3. It’s the original setting).or connect independent.(as show as figure2).
2. When the rated phase voltage of the generator is 380V, 440V, the input terminals B, C and sensing terminals A, C must separate connect the wiring (as show as Figure 4 or figure 5). The voltage between B and C must not be over 300 VAC.
3. F+ F- terminals connect to the generator field. (J and K) FEXT.VR is the potentiometer (1KΩ 1W). These two terminals must be by-pass when external potentiometer is needless.
P.S. : A, B, C, F+ F- the usage of wire gauge are AWG16 or 1.25 mm2 85。
C above 600V.
The EXT.VR connection wires must be made of isolated wiring.
3. ADJUSTMENTS
The voltage setting for 220V/380V/440V and the
frequency setting for 50/60HZ is show in figure7.
Please check the voltage/frequency selector setting
is correct before start the generator.
CAUTION :
THE GENERATOR OR AVR MAY BE DAMAGED
IF THE VOLTAGE / FREQUENCY SELECTOR
SETTING IS INCORRECT.
UFRO DIP:
Close - please refer to solid curre in Figure8.
Open - please refer to dotted curre in Figure8.
1. Before you turn on the generator, please turn the
voltage adjustment and stability adjustment full anti-clockwise. After the generator is on and run stably, turn the voltage adjustment clockwise to reach the required out voltage. (If there is an external potentiometer, turn the external potentiometer to the middle position before adjust internal voltage potentiometer.)
2. Adjust “Stability Adjustment” clockwise slowly to
change the response time between AVR and the generator. If the adjustment is too big, it might cause the voltage instable. If too small, the load voltage will change too much at heavy load. Our suggestion is to trace by the multi-meter DCV. To adjust “stability adjustment”, you
just need to make the multi-meter waving smaller. It can also improve the full load’s voltage drift rate.
4. FIELD FLASHING
When the regulator is operated with the generator for
the first time, the polarity of residual magnetism may be reversed or too small to achieve the necessary build-up voltage for the regulator. If reversing the field connections does not induce build-up, and the residual voltage is less than the specified value of 5 Vac, shut down the Prime-mover and proceed with the following steps :
1. With the Prime-mover at rest and the regulator’s
field output wires disconnected, apply a DC source ( NOT grounded ) of not more than 3~12 Vdc with Positive to F+ and Negative to F-, in series with a current-limiting resistor of 3~5 ohms 20 watt. (The set battery is a suitable source.)
2. Allow approximately 3 seconds before removing
the DC source.
3. With the voltage regulator disconnected ( wires 3 and 4 ), start the prime mover and measure the “ residual ” voltage available at the auxiliary winding. If this voltage is greater than 5 Vac, reconnect voltage regulator, and voltage build-up should be successful. If less than 5 Vac is measured, repeat field flashing procedure.
4. If repeating steps a. and b. does not result in
generator voltage build-up, and residual is greater than 5 Vac, replace voltage regulator.
Package Includes:
1 × Automatic Voltage Regulator Controller AVR EA05A Genset Parts
1 × product Instructions
About LABLT:
LABLT has rich experience in the production, sales and after-sales service of Industrial parts. For many years, we have been committed to providing professional and personalized services to enhance the shopping experience of buyers. If you need any parts, please come to LABLT to buy them. We look forward to cooperating with you!
Item SpecificsCountry of Origin United StatesBrand LABLTMPN OM48627OCEquipment Type Voltage RegulatorModel EA05AWarranty 1 Year
PAYMENT & DELIVERY
Pickup is not available as all items are shipped to buyers - NO EXCEPTIONS
Orders are posted by USPS or Fedex
WARRANTY INFORMATION
The most Products has months warranty .
The warranty does NOT cover damage of faulty Goods caused by: an accident or crash, damage caused in transit, damage cause by unauthorised repairs, improper installation of the Goods.
RETURN POLICY
If you have purchased the wrong Good or are returning a Good as a warranty claim, we will accept a return of that good and issue refund or send out a replacement Good subject to the following:
you must contact us first about the Goods before returning the Goods to us, and if we agree to accept a return of the incorrectly purchased Good or if we agree to accept the warranty claim over the Good then you MUST do the following:
the Goods must be securely and appropriately packed so they are not damaged during transit;
the Goods must be returned in their original packaging;
the Goods must be like new and not show any signs of use or having been installed or fitted;
the claim for refund must be advised to us no later than 30 days after the date you bought the Good.
DESCRIPTIONPAYMENTSHIPPINGRETURN POLICYCONTACT US Shop CategoryStore Home Suspension & Steering Lighting & Lamps◈Fog Lights◈Xenon Headlight Ballast◈Headlight◈Fog Lamps cover◈Turn Lights◈Brake Lights◈Truck Light Strip◈Moto Lighting & Lamps◈Others◈Tail Lights Carburetor◈Lawn Mowers Carburetor◈String Trimmers Carburetor◈Blower Carburetor◈Snow Blower Carburetor◈Saw Carburetor◈Tractor Carburetor◈Motorcycle Carburetor◈ATV Carburetor◈Automobile Carburetor◈Others◈Golf Carburetor◈Gasket◈Rebuild kit◈Intake Manifold Boot Boat◈Steering Shaft Pin◈Yacht Light◈Others Auto Valve◈Pressure Relief Valve◈Air Idle Valve◈VVT Valve◈Transmission Solenoids◈Control Valve◈Valve Body◈EGR Valve◈Others Motorcycle Valve◈Motorcycle Solenoid Valve◈Motorcycle fuel Switch Valve◈Others Fule Injector Brakes & Brake Parts◈Brake Master Cylinder◈Clutch & Clutch Parts◈Motorcycle Hand Brake Handle◈Motorcycle Brake Cable◈Motorcycle Brake Pads◈Others◈ Brake Lines Car Repair Kit Auto Engine System◈Valve Cover & Gasket◈Oil Cooler◈Engine Timing Cover◈Turbine Cover◈Oil Pan◈Automobile Heaters&Accessories◈Engine Coolant Recovery Tank◈Hydraulic Roller◈Glow Plug◈Filter Housing &Accessories◈Engine Rocker Arm Shaft Sleeve◈Engine Hood◈Oil Scale◈Coolant Water Inlet Pipe◈Others Auto Ignition System◈Spark Plug◈Car Ignition Coil◈Spark Plug Protective Cover◈Ignition Switch◈Car Ignition Module◈Others Auto Hub◈Locking Hub◈Hub Bearing◈Wheel Spacers Adapters◈Others Motorcycle Ignition System◈Motorcycle Ignition◈Motorcycle Ignition Coil◈Motorcycle Fuel Switch◈Motorcycle Hand Plate◈Motorcycle Ignition Switch◈Motorcycle Starter Fitting◈Motor Electromagnetic Starter◈Others Motorcycle engine system◈Piston Cylinder Fittings◈Crankshaft◈Others Auto Actuator◈Air Conditioner Actuator◈Door Lock Actuator◈Eccentric Shaft Actuator◈Hood Catch◈AC Blower Motor◈Clutch Actuator◈Fuel Door Opener Actuator◈Others Auto Motor◈Transmission stepper motor◈Power Window Lift Motor◈Brake Caliper Servomotor◈Transfer Case Gear Motor◈Front Running Board Motor◈Blower Resistor◈Others Auto Inlet & Outlet System◈Air Filter◈Intake Exhaust Valves◈Throttle Body◈Power Brake Booster◈Exhaust And Intake Pipes◈Turbocharger◈Others Auto Circuit Wiring Harness◈Airbag Hairspring◈Positive Battery Cable◈Sensor Harness◈Body Wiring Harness◈Gear Shift Control Cable◈Battery Terminal◈Others Transmission Power Hose◈Others Auto Switch◈Door Power Window Switch◈Neutral Safety Switch◈Combination Lever Motorcycle Control System◈Gearbox Shift Regulator◈Thumb Oiler◈Others Auto Sensor◈TPMS Sensor◈Mass Air Flow Sensor◈Oxygen Sensor◈Knock (Detonation) Sensor◈Air Pressure Sensor◈Throttle Position Sensor (TPS)◈Vehicle Speed Sensor◈ABS Wheel Speed Sensor◈Fuel Pressure Sensor◈Crankshaft Position Sensor◈Oil Pressure Sensor◈Ride Height Sensor◈PDC Sensor◈MAP Sensor◈Exhaust Pressure Sensor◈Coolant Temperature Sensor◈Acceleration Sensor◈Others Motorcycle Pump◈Fuel Pump◈Brake Calipers◈Others◈Water Pump Auto Interior◈Plastic Rivets Fasteners◈Trunk Shield◈Sunroof Sunshade Corn◈Armrest Center Box Cover◈Cup Holder◈Inside Door Handle◈Inner Door Panel Handle◈Cigarette Lighter◈Storage Box◈Air Conditioner Vent◈Others◈Seat Covers◈Floor Mats Exterior Trimming Parts◈Roof Rack◈Running Boards/Side Steps◈Bmuper Grille◈Fender Flares◈Front Bumper Grille Guard◈Door Handle◈Fuel tank cap◈Hinge◈Front Bumper◈Rear Bumper◈Motorcycle Wiper Blades◈Window Visors◈Front bumper trim◈ Auto body trim panel Auto Pump◈Fuel Pump◈Water Pump◈High Pressure Fuel Pump◈Air Pump◈Power Steering Pump◈Clutch Master Cylinder◈Oil Pump◈Others Radiators & Parts Special Vehicles & Boats◈Go Kart Parts◈Excavator Parts◈Golf Cart Parts◈Boat Parts◈Snowmobile Parts◈Truck Parts Motorcycle Parts◈Motorcycle Carburetor Parts ATV&UTV Parts◈ATV&UTV Suspension System ◈ATV&UTV Brake System◈ATV&UTV Pump◈ATV&UTV Carburetor Parts◈ATV&UTV Body&Frame◈ATV&UTV Ignition System◈ATV&UTV Engine System◈ATV&UTV Intake&Exhaust System◈ATV&UTV Transmission System◈ATV&UTV Steering System◈ATV&UTV Control System◈ATV&UTV Switch◈ATV&UTV Sensor Industrial Bar♢Collet Chuck♢Drill Bits♢Drill Chuck♢Drill Chuck Arbors♢Edge Finder♢Live Center♢Milling Arbor♢Quick Change Tool Post♢Reamer♢Spring Materials♢Interior Door Fittings♢Paint Sprayers▷Generator Accessories♢Automatic Voltage Regulator♢Others▷Hand Tools♢Balance Level♢Casters♢Drill Bits♢Hydraulic Crimper♢Outside Micrometer♢Steel Tape Measure♢Rivet Gun◈Metalworking Supplies◈Industrial Control Module Home & Garden◈Chainsaw Accessories◈Lawn Mower Accessories◈Leafblower Accessories◈Snowblower Accessories◈Yard, Garden & Outdoor Living◈String Trimmer Accessories◈Others OtherHot Item LABLT (10) 1/4\" Straight In-Line Gas Fuel Shut-off / Cut-off Valves Petcock USD 7.78 LABLT Carburetor For Zama RB-K93 For Echo SRM-225 GT-225Air Filter Fuel Line Kit USD 12.69 Centrifugal Clutch 3/4\" Bore Belt Pulley Drive for Carter Go kart Mini Bike USD 24.10 LABLT Complete Carburetor For Traxxas 2.5 2.5r 3.3 Engine 4910 2.5 T-maxx & 4907 USD 17.48 Fuel Pump For EZGO Marathon 2-cycle Golf Carts 1982-1991 14151-G1 USD 18.33 Excellent Delivery
New List Item LABLT Carburetor For Kohler CH1000 PRO 6285315S 37 HP 6285352S 6285345S 6285315S USD 32.12 LABLT15003-2879 Carburetor For Kawasaki 15003-2977 15004-1046 FD750D W/Gaskets USD 37.49 LABLT 2 PCS Aluminum Commercial Door Closer Independent Valves Control 25-45KG USD 27.58 LABLT Electric Hoist 1760lbs Crane Winch with Wired Remote Control 110V 1350W USD 92.70 LABLT Cut off Wheel Metal & Stainless Steel Thin Cutting Discs 4\",4.5\",5\",6\",7\" USD 16.34 LABLT AVR EA05A Automatic Voltage Regulator Controller For Generator Genset
Description:
Sensing Inpuuut
Voltage 220 / 380 / 440 VAC, 1 phase2 wire
DIP switch selectable
Frequency 50 / 60 Hz, DIP switch selectable
Power Input
Voltage 100 ~ 300 VAC, 1 phase 2 wire
Output
Voltage Max. 90 VDC @ 240 VAC input
Current Continuous 5A
Intermittent 7A for 10 sec
Resistance Min. 15 ohm Max. 100 ohm
Voltage Regulation
< ± 0.5% ( with 4% engine governing )
Voltage Build-up
Residual voltage at AVR terminal > 5 VAC
Thermal Drift
0.03% per °C change in AVR ambient
External Volts Adjustmen
± 7% with 1K ohm 1 watt trimmer
EMI Suppression
Internal electromagnetic interference filtering
Unit Power Dissipation
Max. 8 watt
Under Frequency Protection (Factory Setting)
60 Hz system presets knee point at 55 Hz
50 Hz system presets knee point at 45 Hz
Soft Start Ramp Time
3 sec.
Dimensions
101mm L * 69mm W * 47.5mm H
Weight
183g ± 2%
2. WIRING
When generator supply is over load, N phase will be different with the sharing load by 3 phases (load imbalance). Hence, the voltage from N phase to 3 phases (R.S.T.) will be altered. When the rated voltage of the traditional single input’s AVR is above 220V, it will increase the voltage drift rate by using N phase as the detective input. It will also cause the voltage imbalance.
EA05A can improve the above situation, and increase the generator’s rated voltage usage space,such as 380V, 440V. We can all detect by the “phase voltage”.
1. When the rated phase voltage of the generator is 220VAC, the input terminals B, C and sensing terminals A, C can join together (as show as figure3. It’s the original setting).or connect independent.(as show as figure2).
2. When the rated phase voltage of the generator is 380V, 440V, the input terminals B, C and sensing terminals A, C must separate connect the wiring (as show as Figure 4 or figure 5). The voltage between B and C must not be over 300 VAC.
3. F+ F- terminals connect to the generator field. (J and K) FEXT.VR is the potentiometer (1KΩ 1W). These two terminals must be by-pass when external potentiometer is needless.
P.S. : A, B, C, F+ F- the usage of wire gauge are AWG16 or 1.25 mm2 85。
C above 600V.
The EXT.VR connection wires must be made of isolated wiring.
3. ADJUSTMENTS
The voltage setting for 220V/380V/440V and the
frequency setting for 50/60HZ is show in figure7.
Please check the voltage/frequency selector setting
is correct before start the generator.
CAUTION :
THE GENERATOR OR AVR MAY BE DAMAGED
IF THE VOLTAGE / FREQUENCY SELECTOR
SETTING IS INCORRECT.
UFRO DIP:
Close - please refer to solid curre in Figure8.
Open - please refer to dotted curre in Figure8.
1. Before you turn on the generator, please turn the
voltage adjustment and stability adjustment full anti-clockwise. After the generator is on and run stably, turn the voltage adjustment clockwise to reach the required out voltage. (If there is an external potentiometer, turn the external potentiometer to the middle position before adjust internal voltage potentiometer.)
2. Adjust “Stability Adjustment” clockwise slowly to
change the response time between AVR and the generator. If the adjustment is too big, it might cause the voltage instable. If too small, the load voltage will change too much at heavy load. Our suggestion is to trace by the multi-meter DCV. To adjust “stability adjustment”, you
just need to make the multi-meter waving smaller. It can also improve the full load’s voltage drift rate.
4. FIELD FLASHING
When the regulator is operated with the generator for
the first time, the polarity of residual magnetism may be reversed or too small to achieve the necessary build-up voltage for the regulator. If reversing the field connections does not induce build-up, and the residual voltage is less than the specified value of 5 Vac, shut down the Prime-mover and proceed with the following steps :
1. With the Prime-mover at rest and the regulator’s
field output wires disconnected, apply a DC source ( NOT grounded ) of not more than 3~12 Vdc with Positive to F+ and Negative to F-, in series with a current-limiting resistor of 3~5 ohms 20 watt. (The set battery is a suitable source.)
2. Allow approximately 3 seconds before removing
the DC source.
3. With the voltage regulator disconnected ( wires 3 and 4 ), start the prime mover and measure the “ residual ” voltage available at the auxiliary winding. If this voltage is greater than 5 Vac, reconnect voltage regulator, and voltage build-up should be successful. If less than 5 Vac is measured, repeat field flashing procedure.
4. If repeating steps a. and b. does not result in
generator voltage build-up, and residual is greater than 5 Vac, replace voltage regulator.
Package Includes:
1 × Automatic Voltage Regulator Controller AVR EA05A Genset Parts
1 × product Instructions
About LABLT:
LABLT has rich experience in the production, sales and after-sales service of Industrial parts. For many years, we have been committed to providing professional and personalized services to enhance the shopping experience of buyers. If you need any parts, please come to LABLT to buy them. We look forward to cooperating with you!
PAYMENTSHIPPING & DELIVERYWARRANTY INFORMATIONRETURN POLICY
Pickup is not available as all items are shipped to buyers - NO EXCEPTIONS
Orders are posted by USPS or Fedex
The most Products has months warranty .
The warranty does NOT cover damage of faulty Goods caused by: an accident or crash, damage caused in transit, damage cause by unauthorised repairs, improper installation of the Goods.
If you have purchased the wrong Good or are returning a Good as a warranty claim, we will accept a return of that good and issue refund or send out a replacement Good subject to the following:
you must contact us first about the Goods before returning the Goods to us, and if we agree to accept a return of the incorrectly purchased Good or if we agree to accept the warranty claim over the Good then you MUST do the following:
the Goods must be securely and appropriately packed so they are not damaged during transit;
the Goods must be returned in their original packaging;
the Goods must be like new and not show any signs of use or having been installed or fitted;
the claim for refund must be advised to us no later than 30 days after the date you bought the Good.
All rights reserved.
On Nov 12, 2026 at 19:17:10 PST, seller added the following information:
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.