Specifics and features:Sensing InpuuutVoltage 220 / 380 / 440 VAC, 1 phase2 wireDIP switch selectableFrequency 50 / 60 Hz, DIP switch selectablePower InputVoltage 100 ~ 300 VAC, 1 phase 2 wireOutputVoltage Max. 90 VDC @ 240 VAC inputCurrent Continuous 5AIntermittent 7A for 10 secResistance Min. 15 ohm Max. 100 ohmVoltage Regulation< ± 0.5% ( with 4% engine governing )Voltage Build-upResidual voltage at AVR terminal > 5 VACThermal Drift0.03% per °C change in AVR ambientExternal Volts Adjustmen± 7% with 1K ohm 1 watt trimmerEMI SuppressionInternal electromagnetic interference filteringUnit Power DissipationMax. 8 wattUnder Frequency Protection (Factory Setting)60 Hz system presets knee point at 55 Hz50 Hz system presets knee point at 45...
LABLT Automatic Voltage Regulator Controller AVR EA05A For Generator Genset
Specifics and features:
Sensing Inpuuut
Voltage 220 / 380 / 440 VAC, 1 phase2 wire
DIP switch selectable
Frequency 50 / 60 Hz, DIP switch selectable
Power Input
Voltage 100 ~ 300 VAC, 1 phase 2 wire
Output
Voltage Max. 90 VDC @ 240 VAC input
Current Continuous 5A
Intermittent 7A for 10 sec
Resistance Min. 15 ohm Max. 100 ohm
Voltage Regulation
< ± 0.5% ( with 4% engine governing )
Voltage Build-up
Residual voltage at AVR terminal > 5 VAC
Thermal Drift
0.03% per °C change in AVR ambient
External Volts Adjustmen
± 7% with 1K ohm 1 watt trimmer
EMI Suppression
Internal electromagnetic interference filtering
Unit Power Dissipation
Max. 8 watt
Under Frequency Protection (Factory Setting)
60 Hz system presets knee point at 55 Hz
50 Hz system presets knee point at 45 Hz
Soft Start Ramp Time
3 sec.
Dimensions
101mm L * 69mm W * 47.5mm H
Weight
183g ± 2%
2. WIRING
When generator supply is over load, N phase will be different with the sharing load by 3 phases (load imbalance). Hence, the voltage from N phase to 3 phases (R.S.T.) will be altered. When the rated voltage of the traditional single input’s AVR is above 220V, it will increase the voltage drift rate by using N phase as the detective input. It will also cause the voltage imbalance.
EA05A can improve the above situation, and increase the generator’s rated voltage usage space,such as 380V, 440V. We can all detect by the “phase voltage”.
1. When the rated phase voltage of the generator is 220VAC, the input terminals B, C and sensing terminals A, C can join together (as show as figure3. It’s the original setting).or connect independent.(as show as figure2).
2. When the rated phase voltage of the generator is 380V, 440V, the input terminals B, C and sensing terminals A, C must separate connect the wiring (as show as Figure 4 or figure 5). The voltage between B and C must not be over 300 VAC.
3. F+ F- terminals connect to the generator field. (J and K) FEXT.VR is the potentiometer (1KΩ 1W). These two terminals must be by-pass when external potentiometer is needless.
P.S. : A, B, C, F+ F- the usage of wire gauge are AWG16 or 1.25 mm2 85。
C above 600V.
The EXT.VR connection wires must be made of isolated wiring.
3. ADJUSTMENTS
The voltage setting for 220V/380V/440V and the
frequency setting for 50/60HZ is show in figure7.
Please check the voltage/frequency selector setting
is correct before start the generator.
CAUTION :
THE GENERATOR OR AVR MAY BE DAMAGED
IF THE VOLTAGE / FREQUENCY SELECTOR
SETTING IS INCORRECT.
UFRO DIP:
Close - please refer to solid curre in Figure8.
Open - please refer to dotted curre in Figure8.
1. Before you turn on the generator, please turn the
voltage adjustment and stability adjustment full anti-clockwise. After the generator is on and run stably, turn the voltage adjustment clockwise to reach the required out voltage. (If there is an external potentiometer, turn the external potentiometer to the middle position before adjust internal voltage potentiometer.)
2. Adjust “Stability Adjustment” clockwise slowly to
change the response time between AVR and the generator. If the adjustment is too big, it might cause the voltage instable. If too small, the load voltage will change too much at heavy load. Our suggestion is to trace by the multi-meter DCV. To adjust “stability adjustment”, you
just need to make the multi-meter waving smaller. It can also improve the full load’s voltage drift rate.
4. FIELD FLASHING
When the regulator is operated with the generator for
the first time, the polarity of residual magnetism may be reversed or too small to achieve the necessary build-up voltage for the regulator. If reversing the field connections does not induce build-up, and the residual voltage is less than the specified value of 5 Vac, shut down the Prime-mover and proceed with the following steps :
1. With the Prime-mover at rest and the regulator’s
field output wires disconnected, apply a DC source ( NOT grounded ) of not more than 3~12 Vdc with Positive to F+ and Negative to F-, in with a current-limiting resistor of 3~5 ohms 20 watt. (The set battery is a suitable source.)
2. Allow approximately 3 seconds before removing
the DC source.
3. With the voltage regulator disconnected ( wires 3 and 4 ), start the prime mover and measure the “ residual ” voltage available at the auxiliary winding. If this voltage is greater than 5 Vac, reconnect voltage regulator, and voltage build-up should be successful. If less than 5 Vac is measured, repeat field flashing procedure.
4. If repeating steps a. and b. does not result in
generator voltage build-up, and residual is greater than 5 Vac, replace voltage regulator.
Package includes:
1 × Automatic Voltage Regulator Controller AVR EA05A Genset Parts
1 × product strongly recommend a professional installation.
If you are not sure if the product is suitable for your equipment, please contact us promptly to confirm before purchase.
Please allow for measurement error as all detailed dimensions of the product are measured manually.
Due to the lighting problem when shooting, the product pictures in the link may not reflect the actual color of the item.
Thank you for bookmarking our store and look forward to working with you.
Item SpecificsCountry of Origin United StatesBrand LABLTMPN QS86448QREquipment Type Voltage RegulatorModel EA05A
Payment
All items will be shipped to buyer's address. Please make sure your address in matches the address you would like us to ship to before payment.
Easy Return
If you are unhappy with your purchase for any reason, US buyers can return it to us in an un-used condition in the original packaging within 30 days of purchase and we'll give you a refund or exchange. The refund/Exchange will not include postage/ costs. Please note you MUST contact us to obtain a Return Authorization Number before returning any part. Any parcel without the Return Authorization Number will be rejected.
If your item is faulty or was incorrect, you must contact our sales representative before returning the parcel and we will endeavour to solve the problem effectively. Video or picture is required to show the item condition before we issue the Return Authorization Number.
Important Notice:
1. Any returned item(s) without Return authorization number will be rejected.
2. Please return your item(s) in original packaging and ensure that all packages are securely wrapped.
3. We will not accept responsibility for loss or damage of goods during transit, please ensure that.
Warranty
Most of the products have warranty .In the very unlikely event that you have a problem with our product, please contact us via messages.
response
We aim to maintain high standards of service and strive to achieve 100% customer satisfaction!
Your response is very important to us, and we sincerely hope that you can contact us immediately before providing us with neutral or negative response, so that we can solve your problem satisfactorily.
LABLT Automatic Voltage Regulator Controller AVR EA05A For Generator Genset
Specifics and features:
Sensing Inpuuut
Voltage 220 / 380 / 440 VAC, 1 phase2 wire
DIP switch selectable
Frequency 50 / 60 Hz, DIP switch selectable
Power Input
Voltage 100 ~ 300 VAC, 1 phase 2 wire
Output
Voltage Max. 90 VDC @ 240 VAC input
Current Continuous 5A
Intermittent 7A for 10 sec
Resistance Min. 15 ohm Max. 100 ohm
Voltage Regulation
< ± 0.5% ( with 4% engine governing )
Voltage Build-up
Residual voltage at AVR terminal > 5 VAC
Thermal Drift
0.03% per °C change in AVR ambient
External Volts Adjustmen
± 7% with 1K ohm 1 watt trimmer
EMI Suppression
Internal electromagnetic interference filtering
Unit Power Dissipation
Max. 8 watt
Under Frequency Protection (Factory Setting)
60 Hz system presets knee point at 55 Hz
50 Hz system presets knee point at 45 Hz
Soft Start Ramp Time
3 sec.
Dimensions
101mm L * 69mm W * 47.5mm H
Weight
183g ± 2%
2. WIRING
When generator supply is over load, N phase will be different with the sharing load by 3 phases (load imbalance). Hence, the voltage from N phase to 3 phases (R.S.T.) will be altered. When the rated voltage of the traditional single input’s AVR is above 220V, it will increase the voltage drift rate by using N phase as the detective input. It will also cause the voltage imbalance.
EA05A can improve the above situation, and increase the generator’s rated voltage usage space,such as 380V, 440V. We can all detect by the “phase voltage”.
1. When the rated phase voltage of the generator is 220VAC, the input terminals B, C and sensing terminals A, C can join together (as show as figure3. It’s the original setting).or connect independent.(as show as figure2).
2. When the rated phase voltage of the generator is 380V, 440V, the input terminals B, C and sensing terminals A, C must separate connect the wiring (as show as Figure 4 or figure 5). The voltage between B and C must not be over 300 VAC.
3. F+ F- terminals connect to the generator field. (J and K) FEXT.VR is the potentiometer (1KΩ 1W). These two terminals must be by-pass when external potentiometer is needless.
P.S. : A, B, C, F+ F- the usage of wire gauge are AWG16 or 1.25 mm2 85。
C above 600V.
The EXT.VR connection wires must be made of isolated wiring.
3. ADJUSTMENTS
The voltage setting for 220V/380V/440V and the
frequency setting for 50/60HZ is show in figure7.
Please check the voltage/frequency selector setting
is correct before start the generator.
CAUTION :
THE GENERATOR OR AVR MAY BE DAMAGED
IF THE VOLTAGE / FREQUENCY SELECTOR
SETTING IS INCORRECT.
UFRO DIP:
Close - please refer to solid curre in Figure8.
Open - please refer to dotted curre in Figure8.
1. Before you turn on the generator, please turn the
voltage adjustment and stability adjustment full anti-clockwise. After the generator is on and run stably, turn the voltage adjustment clockwise to reach the required out voltage. (If there is an external potentiometer, turn the external potentiometer to the middle position before adjust internal voltage potentiometer.)
2. Adjust “Stability Adjustment” clockwise slowly to
change the response time between AVR and the generator. If the adjustment is too big, it might cause the voltage instable. If too small, the load voltage will change too much at heavy load. Our suggestion is to trace by the multi-meter DCV. To adjust “stability adjustment”, you
just need to make the multi-meter waving smaller. It can also improve the full load’s voltage drift rate.
4. FIELD FLASHING
When the regulator is operated with the generator for
the first time, the polarity of residual magnetism may be reversed or too small to achieve the necessary build-up voltage for the regulator. If reversing the field connections does not induce build-up, and the residual voltage is less than the specified value of 5 Vac, shut down the Prime-mover and proceed with the following steps :
1. With the Prime-mover at rest and the regulator’s
field output wires disconnected, apply a DC source ( NOT grounded ) of not more than 3~12 Vdc with Positive to F+ and Negative to F-, in with a current-limiting resistor of 3~5 ohms 20 watt. (The set battery is a suitable source.)
2. Allow approximately 3 seconds before removing
the DC source.
3. With the voltage regulator disconnected ( wires 3 and 4 ), start the prime mover and measure the “ residual ” voltage available at the auxiliary winding. If this voltage is greater than 5 Vac, reconnect voltage regulator, and voltage build-up should be successful. If less than 5 Vac is measured, repeat field flashing procedure.
4. If repeating steps a. and b. does not result in
generator voltage build-up, and residual is greater than 5 Vac, replace voltage regulator.
Package includes:
1 × Automatic Voltage Regulator Controller AVR EA05A Genset Parts
1 × product strongly recommend a professional installation.
If you are not sure if the product is suitable for your equipment, please contact us promptly to confirm before purchase.
Please allow for measurement error as all detailed dimensions of the product are measured manually.
Due to the lighting problem when shooting, the product pictures in the link may not reflect the actual color of the item.
Thank you for bookmarking our store and look forward to working with you.
Payment Shipping
All items will be shipped to buyer's address. Please make sure your address in matches the address you would like us to ship to before payment.
Easy Return
If you are unhappy with your purchase for any reason, US buyers can return it to us in an un-used condition in the original packaging within 30 days of purchase and we'll give you a refund or exchange. The refund/Exchange will not include postage/ costs. Please note you MUST contact us to obtain a Return Authorization Number before returning any part. Any parcel without the Return Authorization Number will be rejected.
If your item is faulty or was incorrect, you must contact our sales representative before returning the parcel and we will endeavour to solve the problem effectively. Video or picture is required to show the item condition before we issue the Return Authorization Number.
Important Notice:
1. Any returned item(s) without Return authorization number will be rejected.
2. Please return your item(s) in original packaging and ensure that all packages are securely wrapped.
3. We will not accept responsibility for loss or damage of goods during transit, please ensure that.
Warranty
Most of the products have warranty .In the very unlikely event that you have a problem with our product, please contact us via messages.
response
We aim to maintain high standards of service and strive to achieve 100% customer satisfaction!
Your response is very important to us, and we sincerely hope that you can contact us immediately before providing us with neutral or negative response, so that we can solve your problem satisfactorily.
All rights reserved.
Shop CategoryStore Home Auto Actuator◈AC Blower Motor◈Air Conditioner Actuator◈Clutch Actuator◈Door Lock Actuator◈Eccentric Shaft Actuator◈Fuel Door Opener Actuator◈Hood Catch Auto Circuit Wiring Harness◈Airbag Hairspring◈Battery Terminal◈Body Wiring Harness◈Carplay◈Gear Shift Control Cable◈Positive Battery Cable◈Sensor Harness Auto Engine System◈Coolant Water Inlet Pipe◈Engine Hood◈Engine Timing Cover◈Filter Housing &Accessories◈Glow Plug◈Oil Cooler◈Oil Pan◈Oil Cover◈Valve Cover & Gasket Auto Hub◈Hub Bearing◈Locking Hub◈Wheel Spacers Adapters Auto Ignition System◈Car Ignition◈Car Ignition Coil◈Car Ignition Module◈Ignition Switch◈Spark Plug◈Spark Plug Protective Cover Auto Inlet & Outlet System◈Exhaust And Intake Pipes◈Intake Exhaust Valves◈Throttle Body◈Turbocharger Auto Interior◈Air Conditioner Vent◈Armrest Center Box Cover◈Cigarette Lighter◈Cup Holder◈Inner Door Panel Handle◈Inside Door Handle◈Plastic Rivets Fasteners◈Storage Box◈Sunroof Sunshade Corn◈Trunk Shield Auto Motor Auto Pump◈Air Pump◈Fuel Pump◈High Pressure Fuel Pump◈Oil Pump◈Power Steering Pump◈Water Pump Auto Sensor◈ABS Wheel Speed Sensor◈Air Pressure Sensor◈Camshaft Position Sensor◈Coolant Temperature Sensor◈Crankshaft Position Sensor◈Exhaust Pressure Sensor◈Fuel Pressure Sensor◈Knock (Detonation) Sensor◈MAP Sensor◈Mass Air Flow Sensor◈Oil Pressure Sensor◈Oxygen Sensor◈PDC Sensor◈Ride Height Sensor◈Throttle Position Sensor (TPS)◈TPMS Sensor◈Vehicle Speed Sensor Auto Switch◈Combination Lever Switch◈Door Power Window Switch◈Neutral Safety Switch◈Parking Brake Switch Auto Valve◈Air Idle Valve◈Control Valve◈EGR Valve◈Pressure Relief Valve◈Transmission Solenoids◈Valve Body Boat◈Steering Shaft Pin◈Yacht Light Brakes & Brake Parts◈ Brake Lines◈Brake Master Cylinder◈Clutch & Clutch Parts◈Motorcycle Brake Cable◈Motorcycle Brake Pads◈Motorcycle Hand Brake Handle Business & Bar♢Collet Chuck♢Drill Bits♢Drill Chuck♢Drill Chuck Arbors♢Edge Finder♢Live Center♢Milling Arbor♢Pull Stud♢Quick Change Tool Post♢Reamer♢Spring Materials♢Interior Door Fittings♢Paint Sprayers▷Generator Accessories♢Automatic Voltage Regulator▷Hand Tools♢Balance Level♢Casters♢Hydraulic Crimper♢Outside Micrometer♢Rivet Gun♢Wrenches▷Industrial Control Module♢Control Valves♢Roller Chain▷Metalworking Supplies♢Flap Disc♢Hose Clamp♢Metal Cut Off Wheels♢Sanding Disc♢Welding Wire◈Solar Panel Car Repair Kit Carburetor◈ATV Carburetor◈Automobile Carburetor◈Blower Carburetor◈Gaskets◈Intake Manifold Boot◈Lawn Mowers Carburetor◈Motorcycle Carburetor◈Rebuild kits◈Saw Carburetor◈Snow Blower Carburetor◈String Trimmers Carburetor◈Tractor Carburetor Control Arms & Parts Exterior Trimming Parts◈Bmuper Grille◈Door Handle◈Fender Flares◈Front Bumper◈Front Bumper Grille Guard◈Fuel tank cap◈Hinge◈Motorcycle Decoration◈Rear Bumper◈Roof Rack◈Running Boards/Side Steps◈Window Visors◈Windshield Wiper Blades Fuel Injector Home & Garden▷Chainsaw Parts♢Clutch & Accessories♢Cylinder▷Lawn Mowers Parts♢Air Filter♢Cable♢Deck Parts▷Snowblower Parts▷String Trimmer Parts♢Trimmer Head Lighting & Lamps◈Brake Lights◈Fog Lamps cover◈Fog Lights◈Headlight◈Moto Lighting & Lamps◈Tail Lights◈Truck Light Strip◈Turn Lights◈Xenon Headlight Ballast Motorcycle Control System◈Gearbox Shift Regulator Motorcycle engine system◈Camshaft◈Piston Cylinder Fittings Motorcycle Ignition System◈Motor Electromagnetic Starter◈Motorcycle Fuel Switch◈Motorcycle Hand Plate◈Motorcycle Ignition◈Motorcycle Ignition Coil◈Motorcycle Ignition Switch◈Motorcycle Starter Fitting Motorcycle Pump◈Brake Calipers Motorcycle Valve◈Motorcycle fuel Switch Valve◈Motorcycle Solenoid Valve Other Radiators & Parts SuspensionHot Item LABLT 3pack T25 Trimmer Head For Husqvarna 129L 129DJX 129R 129LK 128LDX Trimmer USD 17.00 500W 36/48V Brushless DC Motor Speed Controller bike Scooter Electric Bicycle USD 15.03 LABLT For Zenith K2112 Carburetor Rebuild Kit For 61 67 68 161 Series USD 12.85 LABLT Shut Off Solenoid For Deere/Kawasaki Replaces 21188-2011&M138477 X475 USD 9.11 LABLT Airless Paint Spray Gun 517 Spray Tip + Nozzle Guard for Sprayers 3600PSI USD 20.59 New List Item LABLT DSE4520 Mains Detection Generator Controller Module LCD Screen 3 Phase USD 45.63 LABLT DSE703 Control Panel Module For Deep Sea Generator Controller Auto Start USD 46.74 LABLT Diode RSK2001 Rectifier Kits Fit For Generator Genset Spare Parts 1200V USD 17.97 LABLT For Automatic Voltage Regulator AVR B-292902 Circuit Board Transistor USD 66.83 LABLT AVR Automatic Voltage Regulator For 4KW-7.5KW Single Phase Generator USD 15.68
On Nov 12, 2026 at 19:17:08 PST, seller added the following information:
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.