Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

DC7 -24V Modbus Rtu 4 Channel Relay Module Switch input output RS485/TTL UART

DC7 -24V Modbus Rtu 4 Channel Relay Module Switch input output RS485/TTL UART
$7.50

Buy Now

  • Home
  • Electronic Component
  • Chips
  • Sensor
  • Arduino Module
  • Raspberry Pi
DC7 -24V Modbus Rtu 4 Channel Relay Module Switch input output RS485/TTL UART Popular Popular

    Product Introduction

    Modbus RTU four-way relay module RS485/TTL UART
    4 inputs 4 outputs
    I. Overview
    Elsay four-way Modbus relay module is equipped with mature and stable 8-bit MCU and RS485 level communication chip. Using standard MODBUS RTU format RS485 communication protocol, it can realize 4 input signal detection and 4 relay output, which can be used for digital detection or power control occasions.

    II. Features
    1. Onboard mature and stable 8bit MCU and MAX485 level conversion chip;

    2, Communication protocol: support standard Modbus RTU protocol;

    3. Communication interface: support RS485/TTL UART interface;

    4. Communication baud rate: 4800/9600/19200, the default is 9600bps, and it supports power-off save;

    5. Optocoupler input signal range: DC3.3-30V (this input cannot be used for relay control);

    6. Output signal: relay switch signal, support manual, flash off, flash off mode, flash off/flash off delay base is 0.1S, the maximum flash off/flash off time can be set to 0xFFFF*0.1S=6553.5S;

    7. Device address: range 1-255, default 255, support power-off save;

    8. The baud rate, input signal, relay status, and device address can be read using software/commands;

    9. There are 4 5V, 10A/250V AC 10A/30V DC relays on board, which can be activated continuously for 100,000 times, with diode effusion protection, and short response time;

    10. On-board relay switch indicator;

    11. Power supply voltage: DC7-24V, support DC socket/5.08mm terminal power supply, with input anti-reverse protection;III. Hardware introduction and description1. Board size2. Interface introduction1. DC-005 socket: DC7-24V power input socket;
    2. VCC, GND: DC7-24V 5.08mm power input terminal;
    3. DC3.3-30V optocoupler signal input:
    IN1: Channel 1 positive
    IN2: Channel 2 positive
    IN3: Channel 3 positive
    IN4: Channel 4 positive
    GND_IN: Common terminal negative
    4. A+, B-: RS485 communication interface, A+, B- are respectively connected to A+, B- of the external control terminal;

    5. Relay switch signal output:
    NC: Normally closed terminal, the relay is short-connected with COM before it is closed, and it is suspended after it is closed;
    COM: public end;
    NO: Normally open end, the relay is suspended before closing, and shorted to COM after closing.
    6, GND, RXD, TXD: TTL level UART communication interface, GND, RXD, TXD are respectively connected to GND, TXD, RXD of the external control terminal;IV. Product Parameters:
    1>.Item name: 4CH Modbus Relay Module
    2>.Work voltage:DC 7V~24V
    3>.Baud rate:4800/9600/19600bps(default 9600bps)
    4>.Optocoupler input signal:DC 3.3V~30V
    5>.Set address:1~255
    6>.Relay contorl mode: ON/OFF,Delay_ON,Delay_OFF mode
    7>.Delay time: 0~6553.5s
    8>.Load: AC 250V 10A or DC 28V 10A
    9>.Protocol:Modbus RTU
    10>.Interface:RS485/TTL UART
    11>.Control channel: 4channel
    12>.Operating Temperature:-20℃~85℃
    13>.Operating Humidity:5%~95%RH
    14>.Module Size:93*90*20mm

    V. Modbus RTU Command:
    1>.Suppose the device address is 0xFF so return 00 10 00 00 00 01 02 00 FF EB 80 and the 9th btye is device address.
    2>.Turn ON CH_1 Relay(Normal Mode):
    Send: FF 05 00 00 FF 00 99 E4
    Return: FF 05 00 00 FF 00 99 E4
    Note_1:The 3rd and 4th byte are relay addresses.So it can be 0x0000,0x0001,0x0002,0x0003.
    Note_2:The 5th and 6th byte are relay data.0xFF00 means turn ON relay and 0x0000 means turn OFF relay.
    3>.Turn OFF CH_1 Relay(Normal Mode):
    Send: FF 05 00 00 00 00 D8 14
    Return: FF 05 00 00 00 00 D8 14
    4>.Turn ON CH_2 Relay(Normal Mode):
    Send: FF 05 00 01 FF 00 C8 24
    Return: FF 05 00 01 FF 00 C8 24
    5>.Turn OFF CH_2 Relay(Normal Mode):
    Send: FF 05 00 01 00 00 89 D4
    Return: FF 05 00 01 00 00 89 D4
    6>.Turn ON All relays:
    Send: FF 0F 00 00 00 08 01 FF 30 1D
    Return: FF 0F 00 00 00 08 41 D3
    7>.Turn OFF All relays:
    Send: FF 0F 00 00 00 08 01 00 70 5D
    Return: FF 0F 00 00 00 08 41 D3
    8>.Set device address to 0x01:
    Send: 00 10 00 00 00 01 02 00 01 6A 00
    Return: 00 10 00 00 00 01 02 00 01 6A 00
    Note: The 9th btye is device address.
    9>.Set device address to 0xFF:
    Send: 00 10 00 00 00 01 02 00 FF EB 80
    Return: 00 10 00 00 00 01 02 00 FF EB 80
    10>.Read device address:
    Send: 00 03 00 00 00 01 85 DB
    Return: 00 03 02 00 FF C5 C4
    Note: The 5th btye is device address.
    11>.Read relay status:
    Send: FF 01 00 00 00 08 28 12
    Return: FF 01 01 01 A1 A0
    Note:The 4th means which one relay.0 means OFF and 1 means ON.
    12>.Read optocoupler input staturs:
    Send: FF 02 00 00 00 08 6C 12
    Return: FF 02 01 01 51 A0
    Note:The 4th means which one input.0 means low level signal input and 1 means high level signal input.
    13>.Set baud rate 4800bps:
    Send: FF 10 03 E9 00 01 02 00 02 4A 0C
    Return: FF 10 03 E9 00 01 C5 A7
    Note:The 9th btye is baud rate value.0x02 is 4800bps.0x03 is 9600bps.0x04 is 19200bps.
    14>.Set baud rate 9600bps:
    Send: FF 10 03 E9 00 01 02 00 03 8B CC
    Return: FF 10 03 E9 00 01 C5 A7
    15>.Set baud rate 19200bps:
    Send: FF 10 03 E9 00 01 02 00 04 CA 0E
    Return: FF 10 03 E9 00 01 C5 A7
    16>.Turn ON CH_1 Relay(2S Flashing Mode):
    Send: FF 10 00 03 00 02 04 00 04 00 14 C5 9F
    Return: FF 10 00 03 00 02 A4 16
    Note_1:The 3rd and 4th byte are relay addresses.So CH1~CH4 can be 0x0003,0x0008,0x000D,0x0012.
    Note_2:The 10th and 11th byte are delay time in second.The minimum delay time is 0.1s.Relay will OFF after delay time.So the delay time in this command is : 0x0014*0.1=2S.
    17>.Turn OFF CH_1 Relay(3S Flashing Mode):
    Send: FF 10 00 03 00 02 04 00 02 00 1E A5 99
    Return: FF 10 00 03 00 02 A4 16
    Note:Relay will ON after delay time.So the delay time in this command is : 0x001E*0.1=3S.

    VI. Package Include:
    1PC 4CH Modbus Relay Module
    • Payment must be received in 5 business days of sale closing.
    • Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
    • Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
    Shipping
    • We maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you contact us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your concerns.
    Refund
    • All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can\'t take a refund.
    • If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
    • If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
    • Home
    • Electronic Component
    • Chips
    • Sensor
    • Arduino Module
    • Raspberry Pi
    DC7 -24V Modbus Rtu 4 Channel Relay Module Switch input output RS485/TTL UART

    Product Introduction

    Modbus RTU four-way relay module RS485/TTL UART
    4 inputs 4 outputs
    I. Overview
    Elsay four-way Modbus relay module is equipped with mature and stable 8-bit MCU and RS485 level communication chip. Using standard MODBUS RTU format RS485 communication protocol, it can realize 4 input signal detection and 4 relay output, which can be used for digital detection or power control occasions.

    II. Features
    1. Onboard mature and stable 8bit MCU and MAX485 level conversion chip;

    2, Communication protocol: support standard Modbus RTU protocol;

    3. Communication interface: support RS485/TTL UART interface;

    4. Communication baud rate: 4800/9600/19200, the default is 9600bps, and it supports power-off save;

    5. Optocoupler input signal range: DC3.3-30V (this input cannot be used for relay control);

    6. Output signal: relay switch signal, support manual, flash off, flash off mode, flash off/flash off delay base is 0.1S, the maximum flash off/flash off time can be set to 0xFFFF*0.1S=6553.5S;

    7. Device address: range 1-255, default 255, support power-off save;

    8. The baud rate, input signal, relay status, and device address can be read using software/commands;

    9. There are 4 5V, 10A/250V AC 10A/30V DC relays on board, which can be activated continuously for 100,000 times, with diode effusion protection, and short response time;

    10. On-board relay switch indicator;

    11. Power supply voltage: DC7-24V, support DC socket/5.08mm terminal power supply, with input anti-reverse protection;III. Hardware introduction and description1. Board size2. Interface introduction1. DC-005 socket: DC7-24V power input socket;
    2. VCC, GND: DC7-24V 5.08mm power input terminal;
    3. DC3.3-30V optocoupler signal input:
    IN1: Channel 1 positive
    IN2: Channel 2 positive
    IN3: Channel 3 positive
    IN4: Channel 4 positive
    GND_IN: Common terminal negative
    4. A+, B-: RS485 communication interface, A+, B- are respectively connected to A+, B- of the external control terminal;

    5. Relay switch signal output:
    NC: Normally closed terminal, the relay is short-connected with COM before it is closed, and it is suspended after it is closed;
    COM: public end;
    NO: Normally open end, the relay is suspended before closing, and shorted to COM after closing.
    6, GND, RXD, TXD: TTL level UART communication interface, GND, RXD, TXD are respectively connected to GND, TXD, RXD of the external control terminal;IV. Product Parameters:
    1>.Item name: 4CH Modbus Relay Module
    2>.Work voltage:DC 7V~24V
    3>.Baud rate:4800/9600/19600bps(default 9600bps)
    4>.Optocoupler input signal:DC 3.3V~30V
    5>.Set address:1~255
    6>.Relay contorl mode: ON/OFF,Delay_ON,Delay_OFF mode
    7>.Delay time: 0~6553.5s
    8>.Load: AC 250V 10A or DC 28V 10A
    9>.Protocol:Modbus RTU
    10>.Interface:RS485/TTL UART
    11>.Control channel: 4channel
    12>.Operating Temperature:-20℃~85℃
    13>.Operating Humidity:5%~95%RH
    14>.Module Size:93*90*20mm

    V. Modbus RTU Command:
    1>.Suppose the device address is 0xFF so return 00 10 00 00 00 01 02 00 FF EB 80 and the 9th btye is device address.
    2>.Turn ON CH_1 Relay(Normal Mode):
    Send: FF 05 00 00 FF 00 99 E4
    Return: FF 05 00 00 FF 00 99 E4
    Note_1:The 3rd and 4th byte are relay addresses.So it can be 0x0000,0x0001,0x0002,0x0003.
    Note_2:The 5th and 6th byte are relay data.0xFF00 means turn ON relay and 0x0000 means turn OFF relay.
    3>.Turn OFF CH_1 Relay(Normal Mode):
    Send: FF 05 00 00 00 00 D8 14
    Return: FF 05 00 00 00 00 D8 14
    4>.Turn ON CH_2 Relay(Normal Mode):
    Send: FF 05 00 01 FF 00 C8 24
    Return: FF 05 00 01 FF 00 C8 24
    5>.Turn OFF CH_2 Relay(Normal Mode):
    Send: FF 05 00 01 00 00 89 D4
    Return: FF 05 00 01 00 00 89 D4
    6>.Turn ON All relays:
    Send: FF 0F 00 00 00 08 01 FF 30 1D
    Return: FF 0F 00 00 00 08 41 D3
    7>.Turn OFF All relays:
    Send: FF 0F 00 00 00 08 01 00 70 5D
    Return: FF 0F 00 00 00 08 41 D3
    8>.Set device address to 0x01:
    Send: 00 10 00 00 00 01 02 00 01 6A 00
    Return: 00 10 00 00 00 01 02 00 01 6A 00
    Note: The 9th btye is device address.
    9>.Set device address to 0xFF:
    Send: 00 10 00 00 00 01 02 00 FF EB 80
    Return: 00 10 00 00 00 01 02 00 FF EB 80
    10>.Read device address:
    Send: 00 03 00 00 00 01 85 DB
    Return: 00 03 02 00 FF C5 C4
    Note: The 5th btye is device address.
    11>.Read relay status:
    Send: FF 01 00 00 00 08 28 12
    Return: FF 01 01 01 A1 A0
    Note:The 4th means which one relay.0 means OFF and 1 means ON.
    12>.Read optocoupler input staturs:
    Send: FF 02 00 00 00 08 6C 12
    Return: FF 02 01 01 51 A0
    Note:The 4th means which one input.0 means low level signal input and 1 means high level signal input.
    13>.Set baud rate 4800bps:
    Send: FF 10 03 E9 00 01 02 00 02 4A 0C
    Return: FF 10 03 E9 00 01 C5 A7
    Note:The 9th btye is baud rate value.0x02 is 4800bps.0x03 is 9600bps.0x04 is 19200bps.
    14>.Set baud rate 9600bps:
    Send: FF 10 03 E9 00 01 02 00 03 8B CC
    Return: FF 10 03 E9 00 01 C5 A7
    15>.Set baud rate 19200bps:
    Send: FF 10 03 E9 00 01 02 00 04 CA 0E
    Return: FF 10 03 E9 00 01 C5 A7
    16>.Turn ON CH_1 Relay(2S Flashing Mode):
    Send: FF 10 00 03 00 02 04 00 04 00 14 C5 9F
    Return: FF 10 00 03 00 02 A4 16
    Note_1:The 3rd and 4th byte are relay addresses.So CH1~CH4 can be 0x0003,0x0008,0x000D,0x0012.
    Note_2:The 10th and 11th byte are delay time in second.The minimum delay time is 0.1s.Relay will OFF after delay time.So the delay time in this command is : 0x0014*0.1=2S.
    17>.Turn OFF CH_1 Relay(3S Flashing Mode):
    Send: FF 10 00 03 00 02 04 00 02 00 1E A5 99
    Return: FF 10 00 03 00 02 A4 16
    Note:Relay will ON after delay time.So the delay time in this command is : 0x001E*0.1=3S.

    VI. Package Include:
    1PC 4CH Modbus Relay Module
    • Payment must be received in 5 business days of sale closing.
    • Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
    • Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
    Shipping
    • We maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you contact us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your concerns.
    Refund
    • All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can\'t take a refund.
    • If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
    • If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.

    Buy Now

    When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


    Related Userbars
           

    More items on eBay

    As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



    All userbars are property of respective authors.
    Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design