Product Details
Product features:
1. This module is divided into two versions, the signal generator and the version with MODBUS function
2. Multi-function support PWM mode, pulse mode, signal source, signal source mode, sine wave mode, support RS485 Modbus communication
3. The module signal source mode has voltage and current calibration function
4. PWM mode voltage, frequency, duty cycle are adjustable
5. Signal source mode voltage source 0-10V adjustable, current source 0-20mA adjustableThe difference is that the power supply with MODBUS version has RS485 communication interface, which can be set up with the upper computer software or collect data, and can also communicate with computers, PLC, DCS, smart meters and other devices! In addition, other functions are the same!Product parameters:
Power supply voltage: DC 7-24V
Product function: PWM mode, pulse mode, signal source mode, sine wave mode
PWM mode: voltage, frequency, duty cycle are adjustable, frequency accuracy up to 0.1%; voltage range: 1-24V adjustable, frequency range: 1Hz-150KHz adjustable, duty cycle range: 0.1-100% adjustable
Pulse mode: time accuracy 0.001S, start delay time T0:0.001-60S, high level time T1:0.001-60S, low level time T2:0.001-60S, pulse number PulseNun:1-60000 (unlimited output when number is set to 0)
Signal source mode: voltage source 0-10V adjustable, current source 0-20mA adjustable (Note: the load is not greater than 250R)
Sine wave mode: 1-1000Hz adjustable, note: voltage peak to peak for about 5V can not be adjusted
Signal load capacity: the maximum output current 30mA (Note: this product is the output is a signal source, can not directly drive high-power load. If you want to use the PWM signal to drive high-power loads, such as motors, LEDs, etc., can be connected externally to the driver module)
Ambient temperature: -10-+70℃
Module size: length 79mm width 43mm height 41mm
Opening size: 76mm long by 39mm wideRestore factory settings: in case of power failure, press and hold P1, then power on and then release, it will be restored.
Calibration function: The module signal source mode has voltage and current calibration function, if the display is not allowed, the following method can be used to calibrate: first power off, press and hold the code switch to power up, it will enter the voltage and current mode, use a multimeter to measure the output voltage (amount GND and 2-10V) or current (amount GND and 4-20MA), rotate the adjustment to the display and multimeter, press the code switch to save, three seconds after power off. Three seconds after power off can be, the accuracy can be calibrated to within 0.1%!PWM mode: press P1 once to enter, press SET key to switch to set voltage, frequency, duty cycle data in turn (duty cycle can also be adjusted directly rotary encoder, no need to enter SET mode), rotary encoder can adjust data (short press to switch coarse adjustment, fine adjustment), the signal is real-time output during the adjustment process, adjust data to complete press SET key to exit, short press encoder to exit SET state Turn on or off the output.
Pulse mode PULSE: Press P2 once to enter, press SET to switch the setting voltage, time T0\\T1\\T2, number of pulses, rotary encoder can adjust the data (short press to switch coarse and fine adjustment), the signal is output in real time during adjustment, press SET to exit when the adjustment data is finished, short press the encoder to turn on or off the output when exit SET state. Note: The voltage of pulse mode and PWM mode is the same, switch to PWM mode to adjust the voltage when you need to adjust it.
Voltage and current signal source mode: Press P3 once to enter, press SET key to switch to set voltage and current in turn, enter that is to start output signal, rotate the encoder to adjust the data (short press to switch coarse adjustment, fine adjustment), the signal is output in real time during the adjustment process, adjust the data to complete press SET key to exit. (Note: 4-20mA current source output when the load can not be greater than 250R)
Sine wave mode: press P3 twice to enter sine wave, enter that is to start output signal (peak to peak is about 5V, voltage is not adjustable), rotary encoder can adjust the frequency, the signal is output in real time during the adjustment process.Communication function.
This signal generation module Modbus version supports RS485 interface Modbus RTU communication protocol
Upper computer software and protocol description: http://pan.baidu.com/s/1eSC3BDSProduct list:
1* Signal generator
- Payment Method
- Shipping Policy
- Returns & Refund Method
- Managed Payment. But we only Accept your Address, please Make sure it\'s 100% right.
- Payment must be received in 5 business days of sale closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping Policy1. We only ship to the confirmed address provided by . please make sure your address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can\'t take a refund.
Returns & Refund Policy- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can\'t take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
response We maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your concerns.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.