Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

AllScan ANH85-RT85 AllStar Node Radio Module - 100% USB-Powered - ASL EchoLink

AllScan ANH85-RT85 AllStar Node Radio Module - 100% USB-Powered - ASL EchoLink
$139.00

Buy Now

AllScan AllStar Node Radio ModulesANH85-RT85 Simplex Node RadioModule v1.1

Fully assembled & tested node radio module with all needed cablesand ferrites, plugs into a Mini PC or RPi 3/4/5 you provide runningASL, HamVOIP,DVswitch, EchoLink, Zello, or other Radio-Over-IP (ROIP), PTT communication, Digital Mode or packet / APRS / data communications app, DigiPi, DireWolf, Fldigi, VARA FM, etc. 100% plug &play module with simple front panel configurability.

Compared toSHARI/PiHat/SA818 nodes these are easier to set up and have far higheraudio quality (55+dB SNR) and RF performance (using an FCC-Certified HT for the radio module), while having none of the disadvantages of SA818 nodes (eg.non-working Squelch Tail Elimination, issues with some PL tones, single-band-only operation, hassle to configure, serial programming script required, poor documentation, etc.)

There is no simpler or morecost-effective way to build a high-quality node. Off/Auto/On powerswitch supports powering the HT on/off automatically based on the USBhost active status. Provides mounting holes for RPi\'s and MiniPC\'s, or just use Velcro or acrylic mounting tape.

100% USB-powered with no separate adapters, chargers or batteriesrequired. Plugs into any MiniPC or RPi 3/4/5 with a single USB cable. The entire node can then be powered from a single AC adapter, USB power bank, or 12~14VDC power source. MiniPCs such as a Dell Wyse 3040 or Beelink T5 are recommended formaximum performance, reliability and 12V compatibility, but Raspberry Pi\'s also work well(with proper power supply eg. PD-capable 27W power supply for RPi5).See theProductspage for more information including How-To Guides and setup instructions.

v1.1 adds a USB-UART IC supporting PTT & COS from RTS & CTS/DCD in addition to the CM108 for enhanced compatibility with Windows apps or other apps that do not support CM108 GPIOs. HT serial programming is also supported.

Includes:AllScan ANH85-M USB RadioInterface, Retevis RT85 HT, USB Cable w/ferrite, and HT K1 2.5mm & 3.5mm cables, allfully assembled and tested with zero assembly required. DoesNOT include a MiniPC or RPi.An optional acrylic back panel is also available that makes it easier to mount RPi 3/4/5\'s, contact me for details.

HT is programmed for 88.5Hz PL but the frequencies and PL tone canbe easily changed right on the front panel. The ANH85-RT85 SupportsLow/Med/High Tx Power levels of ~1, 2, or 2.5 Watts.

Note that some listing pics and the video show the ANH85-RT85 mounted to an RPi or MiniPC, but no RPi or MiniPC is included. You will need to acquire a MiniPC or RPi and load it with ASL3 or other apps of your choice. The ANH85-RT85 then plugs in with a single USB cable, is 100% plug&play, with zero configuration or assembly required.

I can also provide these with a fully configured Dell Wyse 3040 MiniPC or RPi5, or just as the URI without the RT85, see my site for details and options. These are assembled and tested in San Diego CA by an electrical engineer with 30+ years experience in communications systems. The level of quality of my products is about 10 times higher than any other node radio module you will find at anywhere near this price. See my site and FB Group for much more detail on this and my other products.Most orders ship within 1 day. 73, NR9V

Notes & Instructions
  • The volume control on the RT85 should be set to 9 O\'Clock ie. about 20% of fully clockwise. The HT should be powered on/off with the power switch on the URI rather than with the volume control, or leave the power switch set to \"Auto\"
  • The node radio is set up to use 431.18 MHz or 147.48 MHz, with a 88.5 Hz PL. This can be easily changed on the radio. Be sure to confirm that the frequency is not being used by any repeater systems or other hams in your area
  • Using an outdoor antenna can greatly increase range and reduce possible RFI
  • Nodes should kept at least 10 feet away from large metal surfaces and electronics devices such as TVs, computers, file cabinets, appliances, aluminum siding, stucco, electrical panels, cars, various wires & cables, etc. If you experience any noise or other issues be sure the node has at least 10 feet of clear space in all directions, or use an outdoor antenna. It\'s also a good idea to keep transmit antennas at least 20 feet away from people and pets if the transmitter will be keyed for long periods of time eg. 1+ hours per day
  • The Low power setting should be used when longer range is not needed
  • RX and TX level adjustments can be made in the ASL radio tune settings, by logging in by SSH and running \"susbtune\", then follow the prompts to adjust the level settings. An easy way to set Rx levels is to transmit into the node speaking very loudly and increase the Rx volume/gain control until the ADC Clip LED illuminates, then reduce the volume ~10% or so. Be sure the ADC Clip LED never lights during normal use
  • You can check your audio using Parrot mode: Enter DTMF command *921 to enable, *922 to disable. (Be sure you\'re not connected to any other nodes when doing any testing.) N2DYI\'s Parrot Test Node 55553 can also be used. When setting levels keep in mind that it\'s better to be a little on the low side than to have possible clipping and distortion
  • For nodes with WiFi it is recommended to use wired Ethernet when available for best performance
  • If you ever have any issues with DTMF commands not being recognized, this is caused 99% of the time by audio levels being too high to low. Try making small audio level adjustments up and down in the ASL rxmix settings, or with the Rx Level / Mic Gain controls on the HT / URI / UCI
  • If you have any questions be sure to review the How-To Guides at AllScan.info, which are frequently updated.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design