|
>> If you dont know how to design a userbar, then write here a Userbar that you want.
>> If you know how to design them help these people and design what they request.
|
 |
 |
USERBARS.org | Free Forum Userbars
| On eBay now |
3pcs Relay Module for Arduino, ESP32, ESP8266, Raspberry Pi, 1 Channel, 5V, H...
$16.08

3pcs Relay Module for Arduino, ESP32, ESP8266, Raspberry Pi, 1 Channel, 5V, High/Low Level Trigger Product Details Size: 3.3v - 5v Number of Items: 3 Brand: DIYables MPN: DIY-RELAY-3-5V-1C-LH UPC: Does not apply EAN: Does not apply - Connector Type: Screw
- Contact Material: Steel
- Contact Type: Normally Open and Normally Closed
- Current Rating: 10 A
- Mounting Type: Surface Mount
- Connector Type: Screw
- Contact Type: Normally Open and Normally Closed
- Current Rating: 10 A
- Mounting Type: Surface Mount
- Operation Mode: Automatic
- Wattage: 50 watts
- Coil Voltage: 5 volts
- Contact Current Rating: 10 A
- Maximum Switching Current: 10 A
- Maximum Switching Voltage: 250 volts
- Minimum Switching Voltage: 3 volts
- Brand Name: DIYables
- Unit Count: 3 Count
- Number of Items: 3
- Manufacturer: DIYables
- Model: DIY-RELAY-3-5V-1C-LH
- Part Number: DIY-RELAY-3-5V-1C-LH
- Contact Material: Steel
- Relay supports Normally Open and Normally Closed
- Relay supports High-level Trigger or Low-Level Trigger selectable by a jumper
- Relay with Optocoupler Isolation
- Relay with Terminal Blocks for both Input and Output Interface
- Relay with two LED Indicators: power (green LED), the relay status (red LED)
This is 3 pieces of 5V 1-channel relay modules that work with Arduino, ESP32,ESP8266, Raspberry Pi, or any 5V or 3.3V microcontroller. A single packageincludes 3 pieces of relay modules. SPECIFICATION: - Normally open andnormally closed. - High-level trigger or low-Level trigger selection by ajumper. - Optocoupler isolation. - Terminal blocks for both input and output.- Two LED indicators: power (green LED), the relay status (red LED). - Fault-tolerant design, even if the control line is broken, the relay will notoperate. - Operating voltage (power): 5V. - Trigger voltage: 3.3V to 5V. -Trigger current: 5mA. - Maximum load: AC 250V/10A, DC 30V/10A - Dimension:50mm x 26mm x 18.5mm (L x W x H). INPUT INTERFACE: - DC+ : Connect thepositive pole of the 5V power supply. - DC- : Connected the negative pole ofthe 5V power supply. - IN: Signal trigger input (3.3V to 5V, high or low levelsignal selected via a jumper). OUTPUT INTERFACE: - NO: The normally openinterface. - NC: The normally closed interface. - COM: The common interfacefor both normally open and normally closed. High/low level trigger selectionjumper: - If the jumper is placed between COM and L, the relay uses LOW leveltrigger. - If the jumper is placed between COM and H, the relay uses HIGHlevel trigger. HOW IT WORKS: High Level Trigger: - When IN is LOW levelsignal, the NO does not connect with COM and the NC connects with COM. - WhenIN is HIGH level signal, the NO connects with COM and the NC does not connectwith COM. Low Level Trigger: - When IN is LOW level signal, the NO connectswith COM and the NC does not connect with COM. - When IN is HIGH level signal,the NO does not connect with COM and the NC connects with COM. TUTORIALS: -Tutorials for Arduino, ESP32, ESP8266, and Raspberry Pi can be found onproduct page by searching: DIYables 5V relay

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
|
|
|
 |
 |
|