Description
Import duties and fees for shipments to the United States are included in the price.
Please rest assured that no additional duties will be charged upon delivery.
YAMAHA YP-D10
A record player that pursues high-dimensional sound quality using the UR method (Ultimate Refining Method).
The UR method is an approach that focuses on the fact that sound changes depending on the parts and materials that make up every part, and controls vibration modes by suppressing microscopic vibrations below the human audible level.
To achieve more stable rotation, the YP-D10's drive system has a three-stage configuration: a quartz PLL servo for low-frequency disturbances, the large inertia inertia of a heavyweight turntable for high-frequency disturbances, and an FG servo for intermediate frequency disturbances.
For the motor, a DC motor with a large torque of 1.2 kg-cm and good bare characteristics is used. Furthermore, the rotational speed is controlled by a double servo system that combines the FG (frequency generator) servo system and the quartz PLL (phase locked loop) servo system to achieve high rotational accuracy.
The FG servo system controls the rotational speed of the turntable by detecting the signal from the rotational speed detector (FG) so that the frequency of the signal from the FG, which generates a frequency proportional to the rotational speed of the turntable, is constant.
The quartz PLL servo system, introduced to further improve the rotational accuracy of the FG servo system, controls the frequency of the output signal from the FG to eliminate phase deviation from the reference signal oscillated by a crystal oscillator, enabling the rotational accuracy to be improved to the crystal oscillation frequency accuracy. When this quartz PLL is applied, the rotation accuracy is within ±20ppm including temperature drift.
The turntable is made of die-cast aluminum with a diameter of 31 cm, and dynamic balance was precisely determined from the casting stage. The turntable is designed with the mass of the turntable moved to the outer circumference, and has a large mass of inertia of 350 kg/cm2, which improves the load fluctuation at high frequencies where the quartz PLL is not effective.
The power supply section is powerful enough to maintain a constant voltage of 24 V even when drawing a current of 1100 mA, thus ensuring an accurate response to load fluctuations.
The tone arm is a gimbal support system with a pivot made of polished chrome molybdenum steel and has an initial movement sensitivity of 3mg vertically and 5mg horizontally. The arm body is an S-shaped pipe arm made of a special aluminum alloy that is twice as strong and hard as pure aluminum, and the pipe is fully filled with filler material to suppress resonance.
The inside force canceller is a roller string counterweight system that allows for advanced adjustment.
The head shell is made of a highly rigid special die-cast aluminum alloy to reduce the total weight of the tone arm and prevent resonance.
Also, very thin and flexible special lead wires are used for the lead wires to increase the high sensitivity of the arm.
NEGLEX low-impedance cables are used for the pickup cable, so the resistance from the cartridge to the pin plug is reduced to 0.94Ω, less than 2/3 of the conventional value.
In addition, the plugs are gold-plated.
An elevation ring rotary arm height adjustment mechanism with a stroke of 6mm is provided to allow the use of commercially available cartridges. One rotation of the ring can raise or lower the arm by 1mm.
The cabinet is not a box, but a solid 64mm-thick laminated high-density particleboard to reduce the adverse effects of vibration. In consideration of response, a 1.6mm-thick steel plate is used for the back plate to provide vibration isolation and to shield against unwanted radiation from the crystal oscillator circuit and logic circuit.
The arm stand and arm base are made of 1 kg die-cast zinc, and are fixed to the cabinet by squeezing the arm post on the surface like a vise, sufficiently securing the base of the arm to suppress unwanted vibrations.
In addition, a large double-damping insulator is used after careful consideration from the viewpoint of materials.
The silent ending mechanism is equipped with a cueing lever that automatically activates when the needle tip of the cartridge enters the final groove after playing the record, quietly lifts the cartridge from the record surface, and turns off the power supply.
This mechanism uses a photoelectric detector to detect the speed at which the shutter on the bottom of the tone arm moves and drives an electromagnetic solenoid to operate the cueing lever and power switch, thus eliminating any load on the arm's movement and preventing malfunctions.
The finish has an ebony laminated urethane open pore finish.
All my products are 100% Authentic.
Please feel free to contact us if you have any question.
Shipping
We ship using FedEx, DHL and UPS.
Payment
We usually ship within 5〜10 business days of receiving cleared payment.
International Buyers - Please Note:
Import duties and fees for shipments to the United States are included in the price.
Please rest assured that no additional duties will be charged upon delivery.
Import duties, taxes, and fees for countries other than the United States are not included in the product price or shipping cost. These charges are the responsibility of the buyer. Before offerding/purchasing, please check with your country's customs office to determine the amount of these additional fees. These fees are typically collected by the shipping carrier or paid upon receiving the item. Do not confuse these with additional shipping charges. We do not underdeclare the value of items or declare them as “gifts.” Such practices are prohibited by U.S. and international government regulations.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.