Whirlpool W11484836 Refrigerator LED Module Silver Trim | Genuine OEM Part

Whirlpool W11484836 Refrigerator LED Module Silver Trim

Genuine OEM Interior Refrigerator & Freezer LED Light Module Assembly (Silver Trim)

🛑 STOP: Please contact us with your model number to verify compatibility before purchasing.

📝 Product Overview

The Whirlpool W11484836 is a factory-original replacement interior LED light module assembly featuring a stylish silver trim bezel. Positioned on the ceiling or sidewalls of the fresh food or freezer compartments in select French door and side-by-side refrigerators, this genuine OEM part delivers bright, energy-efficient illumination throughout the cabinet interior whenever the doors are opened.

As an Authentic Whirlpool Component, this solid-state LED assembly contains high-efficiency light-emitting diodes mounted on a protected circuit board, finished with a sleek silver accent trim and an impact-resistant clear diffuser lens. Engineered to withstand cold, high-humidity refrigeration environments, choosing a genuine factory replacement ensures exact wiring connector alignment, correct voltage handling, and crisp, flicker-free cabinet lighting that matches your appliance\'s original luxury aesthetic.

🔍 Signs Your Refrigerator LED Light Module Needs Replacement

• Interior Lights Completely Dark: Opening the refrigerator door fails to turn on the interior lights, even though cooling system components continue operating normally.
• Flickering, Strobing, or Dim Illumination: Degrading LED diodes, failing driver circuits, or internal moisture intrusion cause the light to pulse, flicker, or output a weak glow.
• Series Circuit Light Failure: On models where interior LED modules are connected in a series circuit, a single failed module can break the connection and cause all surrounding lights in the section to turn off.
• Cracked Bezel Lens or Moisture Corrosion: Fractures in the plastic housing allow condensation to reach the internal circuit board, causing shorts or corrosion.

🔧 Technical Specifications

• Part Number: W11484836 (Replaces W11382100, W11527430, AP6988813, PS16218081)
• Part Type: Refrigerator Interior Compartment LED Light & Bezel Assembly
• Finish / Style: Metallic Silver Trim Bezel
• Technology: Energy-Efficient Solid-State Low-Voltage LED Module
• Condition: Brand New, Genuine Whirlpool OEM Replacement Part
• Brand Compatibility: Precision engineered to fit select Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana refrigerators.

📦 Professional Installation, Care & Maintenance Tips

⚠️ CRITICAL SAFETY WARNING: ELECTRICAL ISOLATION REQUIRED! Even low-voltage LED modules connect directly to sensitive main control board circuits. **Always disconnect electrical power by unplugging the refrigerator power cord or tripping the main breaker before servicing interior lighting components**. Wear protective safety glasses throughout installation. Pro Tip: Use Non-Marring Trim Tools & Handle Connectors Carefully! The LED light module is held in place by retaining clips inside the cabinet liner or ceiling panel. **Use a plastic putty knife or non-marring trim tool to gently disengage side locking tabs** without scratching the silver trim finish or damaging the plastic liner. Take a clear smartphone reference photo of the wire harness orientation before unhooking the plug connector. When installing your fresh **Whirlpool W11484836** LED module, press the wire harness connector firmly into place until the locking tab clicks securely into place. Align the silver trim housing with the liner opening and snap it straight into the recess. If securing screws are used, **always hand-tighten using standard hand tools** to avoid stripping plastic screw bosses. Installation Steps: Isolate electrical power to the appliance. Carefully pry or unbolt the light housing assembly from the cabinet ceiling or wall. Release the wiring harness locking clip, disconnect the old light board, and remove it. Connect the wiring harness plug to your new genuine **Whirlpool W11484836** silver trim LED module, align the bezel within the liner opening, press firmly until the retaining tabs snap into position (or hand-tighten securing screws), restore power, and open the door to test new lighting.

** Please contact us with your model number to verify compatibility before purchasing. **