Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

VTG Heathkit Variable Frequency Oscillator VF-1 & 2 Q Multiplier QF-1 Untested

VTG Heathkit Variable Frequency Oscillator VF-1 & 2 Q Multiplier QF-1 Untested
$100.00

Buy Now

VTG Heathkit Variable Frequency Oscillator VF-1 & 2 Q Multiplier QF-1 Untested
Heathkit Variable Frequency Oscillator VF-1TheHeathkit Variable Frequency Oscillator VF-1isa classic amateur radio accessory introduced in 1952 that allowed operators to continuously tune their transmitters instead of being restricted to fixed crystal frequencies. It was primarily designed to complement theHeathkit AT-1 Transmitterbut remains a popular vintage component for use with various early \"hollow-state\" transmitters.
  • Tube Complement: Uses a6AU6as the oscillator tube and anOA2voltage regulator for frequency stability.
  • Circuit Type: Features anelectron-coupled Clapp oscillator(series-tuned Colpitts).
  • Output Frequencies: Generates fundamental frequencies in three ranges:1750–2000 kc,7000–7425 kc, and6740–6808 kc.
  • RF Output: Approximately10 voltson fundamental frequencies.
  • Power Requirements: Requires250–350 VDCat 15–20 mA and6.3 VACat 0.45 A for filaments.
  • Dimensions: The unit measures7\" high x 6.5\" wide x 7\" deepand weighs roughly4 lbs.
Band CoverageThe VF-1 provides precalibrated dial scales for several amateur bands:
  • Standard Bands: 160, 80, 40, 20, 15, and 10 meters.
  • 11-Meter Band: Included as a separate range; this was an amateur band until 1958 when it was reassigned to the Citizens Band (CB) service.
  • VHF Potential: By adjusting the 11-meter padder condenser, the unit can generate fundamental frequencies down to6 MHz, which can be doubled for 6-meter or 2-meter band operation.
Construction and DesignThe VF-1 was sold exclusively as a kit for$19.50during its production run from 1952 to 1961.
  • Mechanical Stability: The chassis iscopper-platedfor better conductivity and thermal stability.
  • Shielding: It utilizes an aluminum case with extensive shielding and ceramic coil forms to minimize frequency drift.
  • Controls: The front panel features a large tuning knob with avernier friction drive, a three-position range selector, and a function switch (Off, Standby, On).
Compatibility and UseWhile originally intended for the AT-1, the VF-1 is compatible with many other transmitters of that era.
  • External Power: It does not have a built-in power supply; it typically draws power from the host transmitter through an octal plug, though many enthusiasts now usestandalone homebrew power suppliesto avoid overstressing vintage rigs.
  • Keying: It supportscathode-keyingnatively, but requires modifications for use with transmitters employing blocked-grid keying.
Q Multiplier QF-1 (Lot of 2)TheHeathkit Q Multiplier Model QF-1isa vintage vacuum-tube electronic device used to enhance the selectivity and signal rejection of communications receivers. Produced between1956 and 1960, it allows users to either \"peak\" a desired signal or \"null\" (reject) an interfering one by multiplying the \"Q\" (quality factor) of the receiver\'s intermediate frequency (IF) stage.Key Features and ModesThe front panel includes a mode switch and tuning controls that allow for precise signal manipulation:
  • Sharp Mode: Functions as a narrow bandpass filter to peak a single signal, significantly narrowing the bandwidth to help separate crowded CW or phone signals.
  • Null Mode: Functions as a band-reject (notch) filter, allowing the user to tune out an interfering carrier or \"whistle\" without affecting the desired signal.
  • Broad Mode: Similar to Sharp mode but provides a wider bandwidth, making it more suitable for voice or music signals while still offering some improved selectivity.
  • Off: In this position, the receiver operates normally as if the Q-multiplier were not connected.
Technical Specifications
  • Operating Frequency: Designed for receivers with an IF frequency between450 and 460 kHz(commonly 455 kHz).
  • Tube Complement: Utilizes a single12AX7dual-triode tube.
  • Power Requirements: Typically draws power from the host receiver, requiring6.3 VAC(or 12.6 VAC depending on wiring) at 300 mA and150–250 VDCat 2 mA.
  • Performance: Achieves an effective Q of approximately4,000, which rivals the performance of more expensive quartz crystal filters.
  • Dimensions: The cabinet measures 7 3/8\" W x 4 11/16\" H x 4 1/8\" and CompatibilityThe Heathkit Model QF-1 is compatible with most AM communications receivers that arenotAC-DC (transformerless) types. It connects to the receiver via two cables.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Popular Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design