Universal Rear Trunk Spoiler Wing w/Brake Light GT Style Matte Black

Welcome to our store!

To avoid you buying the wrong parts, DO CHECK the compatible chart above before placing order.

• Choose a vehicle from the "My Garage" list. Or

• Enter your vehicle's details withYear / Make / Model / Trim / Engine.Or

• Contact us: Ask us for double check.

Fitment:
Universal For Sedans 50" Pedestal 2–post

Spoiler Wing Removal and Installation Instructions

Spoiler Disassembly Procedure

• Power-off Protection
  For spoilers with electric lift or brake light functions, disconnect the negative terminal of the vehicle battery first to prevent short circuits.
• Surface Cleaning
  Clean dust and oil stains on the spoiler and its mounting area to avoid scratching the car paint during disassembly.
• Remove External Fasteners
  Bolt-fixed type: Use a wrench/screwdriver of the corresponding specification to unscrew the bolts connecting the spoiler and the trunk lid. On some models, decorative covers are fitted over the bolts and need to be pried off first.
  Adhesive-fixed type: Uniformly heat the adhesive area of the spoiler with a heat gun or hair dryer (low-temperature setting) to soften the double-sided tape, avoiding hard prying that may damage the car paint.
• Disconnect Circuits (Functional Models)
  Unplug the circuit connectors between the spoiler and the vehicle body, and mark the circuits clearly to prevent confusion during subsequent assembly.
• Remove the Spoiler and Clean Residual Adhesive
  Take off the spoiler smoothly, use a glue remover to clear residual double-sided tape on the vehicle body and the spoiler, then wipe the surface clean.

Spoiler Assembly Procedure

• Positioning and Marking
  Place the spoiler at the intended mounting position, adjust it to ensure left-right symmetry and alignment with the original factory reference line, then mark the position with masking tape.
• Pre-treat the Mounting Surface
  Wipe the vehicle body and the spoiler's mounting surface with alcohol to remove grease, enhancing the adhesion or sealing effect.
• Fix the Spoiler
  Bolt-fixed type: Align the bolt holes with the marked positions, screw in the bolts sequentially and tighten them evenly (avoid over-tightening a single point that may deform the car paint). Install sealing washers to prevent water leakage.
  Adhesive-fixed type: Paste special automotive double-sided tape evenly on the adhesive surface of the spoiler. After peeling off the protective film, press the spoiler firmly in alignment with the marked position to ensure tight bonding.
• Connect Circuits (Functional Models)
  Connect the circuit connectors according to the marks made during disassembly, secure the circuits properly (to avoid wear caused by shaking), and power on to test if the electric lift and brake light functions work normally.
• Final Inspection and Finishing
  Bolt-fixed type: Check the tightness of the bolts, and apply anti-rust agent on the bolt heads.
  Adhesive-fixed type: Avoid car washing and high-speed driving within 24 hours after installation to ensure the double-sided tape is fully bonded.
  Conduct an overall inspection to confirm the spoiler is installed flat and symmetric, with no hidden risks of water leakage or abnormal noise.

Notes

• When disassembling an adhesive-fixed spoiler, do not use excessive heating temperature to prevent scorching the car paint.
• When installing bolts, apply moderate force to avoid damaging the bolt holes or vehicle body sheet metal.
• For spoilers with electrical functions, the circuit connections must be insulated to prevent short-circuit faults.

Notice:
Please check the model and important parameters before purchase to avoid unnecessary after-sales problems, if you are not clear, please feel free to contact us, thank you for your cooperation!

Item SpecificsUPC Does not applyBrand VaultProManufacturer Part Number 13545459Manufacturer Warranty 1 YearPlacement on Vehicle RearType spoilerMaterial ABSItems Included Mounting HardwarePerformance Part YesUniversal Fitment YesVintage Car Part NoFinish PaintedColor BlackFeatures Easy InstallationNumber of Pieces 1Attachment Type Screw-OnItem Length 51.18inItem Width 12.2inItem Height 6.3inItem Weight 5.29lbFitment Type Performance/CustomModified Item Yes

About Us:

We are committed to making the best auto-parts products and providing you with better services.
So if you have any quesiton or problem, please fell free to contact us about that.

Payment:

Any payment can be accepted by .

Shipping:

2-8 working days in transit.

Product will be shipped within 2 business days after full payment is received and verified.
USPS, UPS, FedEx shipping will be provided.
Delivery time is about 2-8 business days to most of free return provided.

Contact Us:

Any quesiton or problem, do contact us please.
We are always online to answer.
Note: Do check the compatible chart before paying the items, or contact us for checking the compatibilities for your vehicles/cars/trucks.