Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

UNO R4-Compatible WiFi Board RA4M1 ESP32-S3 WiFi Bluetooth CAN Bus USB-C DAC US

UNO R4-Compatible WiFi Board RA4M1 ESP32-S3 WiFi Bluetooth CAN Bus USB-C DAC US
$21.79

Buy Now

UNO R4-Compatible WiFi board: Renesas RA4M1 MCU + ESP32-S3 Wi-Fi/Bluetooth 5, USB-C, CAN bus, 12-bit DAC, 12x8 LED matrix. NOT genuine Arduino -- compatible board only.

WARNING: ESP32-S3 header & Qwiic connector are 3.3V ONLY, not 5V tolerant. Never connect 5V signals to them.

Specs: RA4M1 48MHz Cortex-M4, 256kB flash, 32kB SRAM. 5V operating voltage (UNO shield compatible). VIN 6-24V, USB 5V. 14 digital I/O pins (8mA max each), 6 analog inputs, DAC on A0.

CAN bus (D13 RX / D10 TX) requires external transceiver (e.g. SN65HVD230) - not included.

Box contains: 1x board only. USB-C cable, shields, and transceiver not included.

Ships fast from the US. Hassle-free returns. Full setup guide available on our website.

Electronics for IoT, Prototyping & DIY

  • ALL ITEMS ·
  • MICROCONTROLLERS ·
  • POWER ·
  • MOTOR CONTROL ·
  • SENSORS ·
  • AUDIO ·
  • COMPONENTS
 

UNO R4-Compatible WiFi Development Board -- RA4M1 & ESP32-S3, Wi-Fi, Bluetooth, USB-C, CAN Bus, 12-Bit DAC, LED Matrix

This UNO R4-compatible WiFi board is built around the same core chipset used in certain officially branded UNO R4 WiFi boards -- a 32-bit Renesas RA4M1 microcontroller paired with an ESP32-S3 module for Wi-Fi and Bluetooth 5. It adds a built-in 12x8 LED matrix, 12-bit DAC, onboard op-amp, USB-C, Qwiic I2C, and CAN bus support, while keeping the classic 5V UNO form factor for shield compatibility. This is an Arduino-compatible board, not a genuine Arduino-branded product.

⚠️ Important: 3.3V vs 5V Circuits

The ESP32-S3 wireless coprocessor, its dedicated header, and the Qwiic connector operate at 3.3V only and are NOT 5V tolerant. Never connect a 5V signal to these -- doing so can permanently damage the ESP32-S3 module.

🔧 How It Works

This board uses a dual-MCU design rather than one chip doing everything:

  1. RA4M1 (Main MCU) -- Runs your sketch and controls all digital/analog pins, the LED matrix, DAC, op-amp, and CAN controller. Operates at 5V.
  2. ESP32-S3 (Wireless Coprocessor) -- A separate, dual-core chip dedicated to Wi-Fi and Bluetooth 5, operating at 3.3V.
  3. Internal Logic-Level Bridge -- Lets the two chips exchange data safely across the 5V/3.3V voltage difference automatically.
⚡ Key Features
  • Renesas RA4M1 Microcontroller -- 32-bit Arm Cortex-M4 at 48 MHz with FPU, 256 kB flash, 32 kB SRAM, 8 kB EEPROM
  • ESP32-S3 Wi-Fi & Bluetooth Coprocessor -- Dual-core module with Wi-Fi 4 (2.4 GHz) and Bluetooth 5 LE built in
  • Built-In 12x8 LED Matrix -- 96 programmable red LEDs for animations, scrolling text, and sensor readouts
  • 12-Bit DAC & Onboard Op-Amp -- Generate analog waveforms and buffer/amplify signals directly on the board
  • USB-C, Qwiic I2C & CAN Bus -- Modern connectivity for programming, sensors, and automotive/industrial projects
  • Full UNO Shield Compatibility -- Same 5V operating voltage and pin layout as classic UNO boards
📐 SpecificationsMain MicrocontrollerRenesas RA4M1 (R7FA4M1AB3CFM), 48 MHz Arm Cortex-M4 with FPUWireless ModuleESP32-S3-MINI-1-N8, dual-core, Wi-Fi 4 (2.4 GHz) & Bluetooth 5 LEFlash / SRAM / EEPROM256 kB / 32 kB / 8 kBOperating Voltage5V (RA4M1) / 3.3V (ESP32-S3, internal only)Input Voltage (VIN)6–24V (barrel jack or header)USB Input Voltage4.8–5.5V via USB-C (do not exceed 5V)Digital I/O Pins14, each rated up to 8 mA maxAnalog Input Pins6 (A0–A5)DAC ResolutionUp to 12-bit (on pin A0)LED Matrix12x8 (96 LEDs), red, charlieplexedCommunication1x UART, 1x SPI, 2x I2C (incl. Qwiic), 1x CAN (external transceiver required)USB ConnectorUSB-COperating Temperature-40°C to +85°CBoard DimensionsApprox. 68.6 × 53.3 × 15 mm (2.70 x 2.10 x 0.55 inches) L × W × H📦 What\'s in the Box
  • 1x UNO R4-Compatible WiFi Board

USB-C cable, jumper wires, and shields are not included.

🛒 What You\'ll Need
  • USB-C cable -- for programming and powering the board
  • CAN transceiver module (e.g., SN65HVD230) -- required to use the CAN bus on a real network
🔌 Compatible With
  • Arduino IDE (Desktop) and Arduino Cloud Editor, using an RA4M1-compatible board package
  • Existing 5V UNO-format shields and accessories
  • Qwiic-standard I2C sensor and actuator modules (3.3V only)
🎯 Typical Applications
  • IoT and smart home projects using built-in Wi-Fi and Bluetooth
  • Visual response and status displays using the onboard LED matrix
  • Audio signal generation and analog projects using the 12-bit DAC
  • Automotive, robotics, or industrial prototyping using CAN bus
  • STEM education and general-purpose learning projects

⚠️ Important Notes

  • Do not power the board with more than 5V through the USB-C port
  • Never connect a 5V signal to the ESP32-S3 header or Qwiic connector
  • Digital GPIO pins max out at 8 mA -- use an external driver for higher-current loads like motors or servos
  • CAN bus requires an external transceiver module; it will not work with the pins alone
🏪 About Envistia Mall

Envistia Mall is a US-based electronics retailer specializing in development boards, sensors, modules, and components for makers, engineers, and educators. We ship from the United States with fast handling times, and full setup documentation is available for this board on our website.

📦 Fast Free US Shipping | 🔄 Hassle-Free Returns | 📧 Responsive Customer Support

Visit our store for compatible shields, sensors, detectors, and more accessories for your microcontroller projects.

Featured Products

Arduino Uno R3 Compatible Board ATmega328P CH340 USB - Board Only - USA Seller

$9.79

SA818S-CE UHF or VHF 1W Analog RF Radio Transceiver Module w/ RDA1846S IC

$19.89

D1 Mini NodeMCU Arduino WiFi LUA ESP8266 ESP-12 WeMos-Compatible Microcontroller

$7.49

MEGA2560 PRO MINI ATmega2560-16AU CH340G Development Board

$18.89

PJRC Teensy 4.1 iMXRT1062 Microcontroller Development Board w/ SD Card, Ethernet

$37.50

MEGA2560 R3 ATmega2560-16AU CH340G Development Board with or without Cable

$22.49

Digispark ATtiny85 Development Board Arduino Compatible Microcontroller

$8.79

PJRC Teensy 4.0 iMXRT1062 Microcontroller Development Board Unlocked & Lockable

$24.80 Add suggested items to your listings - Check it out on 3Dsellers.com

· All Rights Reserved to My Store · 

listing template by 3Dsellers.com - Try for Free!

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design