Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

Thin-Cut Guide Rail Stop Compatible with Festool FS Series, Black

Thin-Cut Guide Rail Stop Compatible with Festool FS Series, Black
$20.99

Buy Now

Thin-Cut Guide Rail Stop Compatible with Festool FS Series
  • REPEAT WITHOUT REMEASURING — Tired of measuring the same strip width before every cut? Press your board edge against the end of the stop\'s leg, and your guide rail\'s cutting edge sits 165 mm inward, giving your next strip the same width reference as the last without laying out the offset again as you work through a stack of boards for the next stage of your project.
  • SLIDE INTO PLACE — The key enters the T-slot at the top of your guide rail\'s rear edge, the body wraps around that edge, and the 6 mm leg extends underneath to meet your board. The slot geometry is based on fitting to a real rail, so the plastic part follows the rail\'s rear edge; your guide rail and mounting hardware are not included.
  • KEEP STRIPS PARALLEL — Use two stops, one near each end of your guide rail, to set the cutting edge parallel to your board edge before you start the saw. Press your board against both leg ends to take up the small amount of slot clearance in the same direction each time, so repeated rail placements start from consistent contact instead of eyeballing the rail again.
  • CHECK YOUR STOCK — Measure your board thickness before setting up: this stop needs stock at least 6.5 mm thick so its under-rail leg has the clearance it needs. Whether you are cutting strips from boards at your workbench or sheet material on a jobsite, that thickness check tells you whether the stock works with the leg before you line up your next cut and start your saw.
  • READ THE WIDTH — The width is embossed on top of the stop, putting the cutting offset where you look as you set up your guide rail. Read the marking before you bring your board against the leg, then get on with the next strip instead of checking a separate note to identify the stop\'s setting when you return to your bench after sanding or assembling another part of your project. WHAT\'S IN THE BOX — Only the item named in the title. No hardware is included (see the description).

Cutting a run of strips should not mean measuring the same offset over and over. Lining up your guide rail again after each cut slows the job and makes consistent widths harder to repeat.

This thin-cut stop is a plastic part that positions your guide rail from the edge of your board. Press the board against the end of the leg and the rail\'s cutting edge sits 165 mm inward, giving you a repeatable reference for the next strip. The width is embossed on top, so you identify the setting right on the stop instead of keeping a separate note beside your work.

Slide the key into the T-slot at the top of your guide rail\'s rear edge. The body wraps around that edge while the thin leg extends underneath, where its end meets your board. This arrangement puts the contact point below the rail and uses the board edge to establish the cutting offset.

Use two stops, one near each end of your guide rail, to keep the cutting edge parallel to the board edge. Press the board against both leg ends before cutting. That pressure takes up the small amount of slot clearance in the same direction each time, giving you a consistent starting reference as you move through repeated cuts.

Check your stock before setting up. The under-rail leg is 6 mm thick, and the workpiece needs to be at least 6.5 mm thick to accommodate it. Make that thickness check before bringing the rail onto your board, then use the leg ends as your placement reference.

For woodworkers cutting repeated strips from boards or sheet material, this stop makes rail placement a repeatable step rather than another measurement.

HARDWARE NOT INCLUDED: Only the item named in the title is in the box. Every setup is different: depending on yours, mounting it or attaching it to an existing part may use hardware you already have, such as the original screws, or you may need to buy your own screws, bolts, tape or adhesive to suit your situation. No hardware of any kind is included with this listing.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design