STM32F401RCT6 STM32F401CCU6 STM32F411CEU6 System Development Board Type-C USB

• Visit store
• Items for sale
• About us

Product Details

STM32F411CEU6Type-CProduct description:
This is a STM32F411CEU6 core development board, the core core is ARM Cortex®-M4. It is rich in resources, backed by powerful resources provided by STMicroelectronics. It is a good choice whether to use it for learning or for secondary development.Module parameters:
IC model: STM32F411CEU6
IC storage: 512 Kbytes flash, 128 Kbytes SRAM
External crystal oscillator: 25MHz high-speed crystal +32.768KHz low-speed crystal
Back flash pad: Users can solder and install flash by themselves as needed (W25Q32JVSSIQ is recommended)
Ready-made communication interfaces: Type-C USB, SWD, USART (A9:TX A10:RX).Package Included:1*STM32F411CEU6 development board
STM32F401CCU6 MicroUSB
Product introduction:
STM32F401
Frequency up to 84 MHz
Memories
– Up to 256 Kbytes of Flash memory
– 512 bytes of OTP memory
– Up to 64 Kbytes of SRAMSince the STM32F401 has a small memory, you need to attach a flash to simulate a USB flash drive. Recommended flash: W25Q32JVSSIQ 32MBit
Package Included:
1pcs*STM32F401CCU6 Development Board Minimum SystemSTM32F401RCT6 Type-CProduct Features:
With 2 high brightness LEDs, red power light, blue for user test light
25MHZ high speed crystal & 32.768Khz 6PF low speed crystal
Using lead-free process, send 2 rows of row of pins and SWD download 4PIN bent pin, more convenient and environmental protection
16-pin TYPE-C high quality interface, durable and reliable
With 3 buttons, reset button, BOOT0 button, user button.Parameter description;
25MHZ high speed crystal & 32.768Khz 6PF low speed crystal
Use lead-free process, send 2 rows of row pins and SWD download 4PIN bend pins, more convenient and environmental protection
There are 2 high brightness LED lights, red power light, blue for user test light
There are 3 buttons, reset button, BOOT0 key, user button
16-pin TYPE-C high quality interface, durable and reliable
Have reserved Flash pads, provide USBDisk&&FATFFS routines
Factory has burned respiratory program, provide source program and hex burn-in program for your learning convenience.
Support MicroPython programming, provide available MicroPython firmware, see link for configuration file, but no technical answer!How to enter the ISP mode download:
ISP mode download
Method 1: In the power-on state, press and hold the BOOT0 key and the reset key, then release the reset key and release the BOOT0 key after 0.5 seconds
Method 2: In the power-down state, press and hold the BOOT0 key, then release BOOT0 after 0.5S of power-up
USB cable connects to MCU\'s TYPE-C interface, serial port connects to PA9, PA10, download software recommends STM32CubeProg, WeAct Studio Download Tool
Serial port download
USB to serial port (ex.: CH340) TX - PA10 ,RX - PA9, and do not connect the MCU Type-C to the computer, you must use external power supply, otherwise it will affect the MCU download
Use STM32CubeProgammer for serial download
USB download (DFU download)
STM32CubeProgrammer check the USB mode, WeAct Studio Download Tool double-click WeAct Studio USB Download Tool.bat, then follow the prompts
MCU enters ISP mode, use USB cable to connect to PC
Select the firmware, the rest of the operation is the same as the serial port download
Steps to use the software.
Connect the core board to the computer with the data cable, the WeAct HID device will appear
Press and hold the KEY key, re-power or reset into Bootloader
Select the firmware, click <Download Firmware> to complete the download
The selected firmware will be updated with the KEIL recompile, no need to reselectTo enter the bootloader method:
Press and hold <KEY key>, re-power or reset, C13 LED blinks to release
APP into the bootloader reference stm32f401_test_APP 0x8004000.zip project
In the burn-in bootloader
Click/double click <KEY key> for C13 LED to turn on/off
SW debug port is open, you can use debugger to burn, no need to enter DFU mode
How to exit the bootloader
Reset the MCU, reset the key/uploader click <MCU reset
Long press <KEY key>, C13 LED blinks to releaseCaution:
The first time you burn the bootloader, the MCU will not run down, while the C13 LED 200MS blinks, just reset the MCU again.
Bootloader and APP burning software source code are not openProduct List:
1* Development board
2* Single row of pins
1* Curved pins

• Payment Method
• Shipping Policy
• Returns & Refund Method
  • Managed Payment. But we only Accept your Address, please Make sure it\'s 100% right.
  • Payment must be received in 5 business days of sale closing.
  • Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
  • Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
  Shipping Policy

  1. We only ship to the confirmed address provided by . please make sure your address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
  2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
  3. All package need to wait 30 days,Please take care it.Less than 30 days,we can\'t take a refund.

  Returns & Refund Policy
  • All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can\'t take a refund.
  • If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
  • If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
  response

  We maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your concerns.