Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

SHT31 Temperature SHT31-D Humidity Sensor Module Microcontroller IIC I2C...

SHT31 Temperature SHT31-D Humidity Sensor Module Microcontroller IIC I2C...
$11.07

Buy Now

SHT31 Temperature SHT31-D Humidity Sensor Module Microcontroller IIC I2C Breakout Weather 3V 5V Compliant for Arduino Temperature and Humidity Sensor Description

Description:Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally we have some that have a true I2C interface for easy reading. The SHT31-D sensor has an excellent ±2% relative humidity and ±0.3°C accuracy for most uses.Unlike earlier for SHT sensors, this sensor has a true I2C interface, and (bonus!) even with two address options. It also is 3V or 5V compliant, so you can power and communicate with it using just about any microcontroller or microcomputer.Such a lovely chip - so we spun up a breakout board with the SHT31-D and some supporting circuitry such as pullup resistors and capacitors. Each order comes with one fully assembled and tested PCB breakout and a small piece of header. You\'ll need to solder the header onto the PCB but it\'s fairly easy and takes only a few minutes even for a beginner.Power Pins:Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller - e.g. for a 5V micro like for Arduino, use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3VGND - common ground for power and logicI2C Logic pins:SCL - I2C clock pin, connect to your microcontrollers I2C clock line. This pin has a 10K pullup resistor to VinSDA - I2C data pin, connect to your microcontrollers I2C data line. This pin has a 10K pullup resistor to VinOther Pins:ADR - This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45RST - Hardware reset pint. Has a 10K pullup on it to make the chip active by default. Connect to ground to do a hardware reset!ALR - Alert/Interrupt output. You can set up the sensor to alert you when an event has occured. Check the datasheet for how you can set up the alertsPackage Included:1 X SHT31-D Temperature Humidity Sensor

Features:

  • 1PCS SHT31 Temperature SHT31-D Humidity Sensor Module Microcontroller IIC I2C Breakout Weather 3V 5V Compliant For Arduino
  • SHT31-D Temperature Humidity Sensor
  • Power Pins: Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller - e.g. for a 5V micro like for Arduino, use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3V GND - common ground for power and logic
  • I2C Logic pins: SCL - I2C clock pin, connect to your microcontrollers I2C clock line. This pin has a 10K pullup resistor to Vin SDA - I2C data pin, connect to your microcontrollers I2C data line. This pin has a 10K pullup resistor to Vin
  • Other Pins: ADR - This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45 RST - Hardware reset pint. Has a 10K pullup on it to make the chip active by default. Connect to ground to do a hardware reset! ALR - Alert/Interrupt output. You can set up the sensor to alert you when an event has occured. Check the datasheet for how you can set up the alerts

Product Details:

  • Handling

    We will ship all orders within 1 business day of payment.

  • Delivery We Do Not Ship Outside of the Continental US.
  • Return Policy All items qualify for returns within 30 days of receipt. Buyer is responsible for return shipping on any item that is not damaged.
  • response

    We take our reputation seriously, we buy and sell online, so we understand the value of trust. If you are unsatisfied with your order, please contact us and we will work with you to resolve it to your satisfaction.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Popular Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design