Rcexl K1 V2.0 Opto Gas Engine Kill Switch KEY FEATURES- Remote engine kill from any spare / AUX receiver channel - on the ground or in the air, including when the model is out of control.- Fiber Optic Coupled input/output isolates the ignition system from the radio system (no interference).- Fail-safe shutdown: switching off the transmitter or receiver power cuts the ignition automatically.- Remote-mountable bright LED indicates when the ignition is armed.- High-power MOS-FET output: up to 20 Volt / 16 amp (IRF7456); low 3 Volt / 3 amp output.- Low voltage drop - less than 150 mV; PIC12F675 controller; 100% surface mount construction.- Works with Li-Po / Li-Ion / A123 / Ni-MH / NiCad ignition batteries.- Heavy gauge wires with universal connectors; only 0.3 oz (8 g)
Rcexl K1 V2.0 Opto Gas Engine Kill Switch
Fiber Optic Remote Ignition Cut Off for RC Gasoline Airplanes | Ships from US Warehouse
Brand new | LED armed indicator | Fail-safe engine stop | For DLE / DA / DLA / AGM / Zenoah CDI gas engines
OVERVIEW
Shut down a gasoline engine safely from your transmitter. This compact switch sits between the ignition battery and the CDI module and plugs into a spare
receiver channel. Its fiber-optically coupled input/output keeps the ignition system electrically isolated from your radio system, so ignition noise cannot
reach the receiver. A bright remote-mountable LED shows when the ignition is armed, and the engine cuts automatically if transmitter or receiver power is
lost.
KEY FEATURES
- Remote engine kill from any spare / AUX receiver channel - on the ground or in the air, including when the model is out of control.
- Fiber Optic Coupled input/output isolates the ignition system from the radio system (no interference).
- Fail-safe shutdown: switching off the transmitter or receiver power cuts the ignition automatically.
- Remote-mountable bright LED indicates when the ignition is armed.
- High-power MOS-FET output: up to 20 Volt / 16 amp (IRF7456); low 3 Volt / 3 amp output.
- Low voltage drop - less than 150 mV; PIC12F675 controller; 100% surface mount construction.
- Works with Li-Po / Li-Ion / A123 / Ni-MH / NiCad ignition batteries.
- Heavy gauge wires with universal connectors; only 0.3 oz (8 g).
SPECIFICATIONS
Brand : Rcexl
Model / Version: K1, Ver 2.0 (Item 2205)
Product type : Opto (fiber-optic coupled) gas engine kill switch / remote ignition cut-off
Isolation: Fiber Optic Coupled input/output - ignition isolated from receiver
Controller: PIC12F675
Output: Up to 20 Volt / 16 amp MOS-FET (IRF7456); low to 3 Volt / 3 amp output
Voltage drop: Less than 150 mV
Battery input: Li-Po / Li-Ion / A123 / Ni-MH / NiCad
Ignition supply: 4.8-6 V CDI ignition system (per supplied wiring diagram)
Receiver connection: Spare / AUX channel, Futaba-style universal servo plug
Status indicator: Remote-mountable bright LED, lit when ignition is armed
Weight: 0.3 oz (8 g)
Module size: Approx. 17 x 38 x 7.5 mm (0.67 x 1.5 x 0.29 in), module body only, per published reseller spec
Construction: 100% surface mount, heavy gauge wires, universal connectors
BEC function: NOT INCLUDED - the receiver requires its own power supply
Condition: Brand new
WHAT\'S IN THE BOX
1 x Rcexl K1 V2.0 Opto Gas Engine Kill Switch
Supplied with the pre-wired harness, universal connectors and the LED
indicator. Connector style, wire colour order and LED mounting may vary
slightly between production batches.
NOT INCLUDED: ignition battery, receiver, transmitter, BEC / receiver pack,
CDI ignition module, engine, servo extensions or tools. Photos showing an
engine or receiver are for illustration only.
COMPATIBILITY & FITMENT
YES - two-stroke gasoline RC engines with electronic CDI ignition, commonly DLE 20 / 30 / 35RA / 55 / 55RA / 60 / 111 / 170 / 222, DA, DLA, AGM 30 / 60,
Zenoah, EME and similar 20cc-222cc engines. Also used in large-scale RC cars and boats. Requires a receiver with one free AUX channel.
NO - glow / nitro engines without electronic ignition, electric power systems, or any installation where you expect this switch to power the receiver (it has
no BEC).
PLEASE CHECK - your ignition battery voltage, connector type and polarity, and that your receiver has its own separate power supply. Unsure? Send us your
engine and radio model via Messages and we will confirm fitment before you buy.
WIRING & SETUP
1. Secure the module inside the fuselage away from exhaust heat, fuel and vibration; foam wrap is recommended. Keep it clear of moving linkages.
2. Wire the switch IN SERIES between the ignition battery and the CDI ignition module. Observe polarity on the red / black power leads before connecting.
3. Plug the three-wire servo lead into a spare receiver channel and assign atransmitter switch to that channel in your radio.
4. Power the receiver separately. This unit does NOT contain a BEC (Battery Eliminator Circuitry); it will not supply power to your receiver or servos.Use a receiver pack or a separate BEC.
5. The supplied sheet also shows an optional DIY arrangement for powering the receiver from the ignition supply by shorting two marked joints; in that case the BATTERY IN wires are not used (best cut off) and only the ignition wires are retained. Only attempt this if you fully understand your power system.
6. With the propeller removed, arm the ignition and confirm the LED lights. Flip the assigned switch and confirm the engine stops. Repeat the check before every flying session.
7. Fail-safe check: with the engine stopped, turn off the transmitter (or receiver power) and confirm the ignition is cut.
IMPORTANT: No reverse-battery protection is claimed on the supplied instruction sheet. Double-check polarity before applying power. Do not exceed the stated voltage and current ratings.
SAFETY & USE
- For model hobby use only. Not for use in any man-carrying vehicle.
- CDI ignition systems produce high voltage. Never touch the ignition lead, spark plug cap or module wiring while the engine is running.
- Remove the propeller for all bench setup and testing; secure the model and keep hands, tools and loose clothing clear of the propeller at all times.
- This switch is a safety aid, not a substitute for a correctly set throttle fail-safe, a physical kill arrangement or a pre-flight check.
- Keep the unit clear of water, fuel, grease and corrosive materials. Small parts - keep away from children.
Package included
Attention:The kill switch not including BEC function (Battery Eliminator Circuitry) .
Contact Us
Please feel free to contact us to resolve any issue, Generally we will reply in 1 business days.
Payment
We Accept Credit Cards, Debit Cards, Gift Cards, Apple Pay, Google Pay, PayPal and PayPal Credit,etc.
Import duties, taxes, and charges are not included in the sale price.
Shipping
Item(s) will be shipped within 1-2 business day after confirmed payment from our US stock.
Returns Policy
We will accept the return of item(s) that was purchased from ZY-Hobby within 30 days of receipt of
shipment.Customers must agree to the following in order to ship item(s) back to us:
1) We accept return item(s) within 60 days after you received the item.
2) Please offer us tracking number if you returned item(s).
3) Return shipping cost is responsible by buyer.
4) The item(s) MUST be in unused condition AND in its original packaging (cannot be glued or tampered with in any fashion).
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.