Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

Pedal Riser Compatible with Playseat Challenge, Black

Pedal Riser Compatible with Playseat Challenge, Black
$35.99

Buy Now

Pedal Riser Compatible with Playseat Challenge
  • BETTER PEDAL ANGLE — If your pedals sit too low relative to your driving position, changing their angle starts with raising them. This riser lifts the pedal assembly on your racing seat for a better angle relative to where you sit. Put the change where your feet meet the controls, whether you are settling in for a short drive or spending the evening on your simulator.
  • PLAN THE HEIGHT — Check the space around your pedal assembly against the riser\'s 168 mm height before changing your setup. That measurement gives you a concrete starting point for planning how your pedals sit relative to your racing seat, rather than judging the change by eye. Use it when laying out your cockpit at home and considering the raised pedal position from where you sit.
  • KEEP YOUR RACING SEAT — Change the pedal position without starting over with a different racing seat. This riser works with your racing seat\'s pedal assembly, putting the change at your feet rather than replacing the cockpit around you. For a sim-racing setup you already know, it gives you a way to improve the pedal angle while keeping your attention on the part of the layout you want to change.
  • PREPARE THE PEDAL TUBES — Fitting the riser involves trimming a small amount of foam around your racing seat\'s pedal tubes. Knowing about that step before you begin lets you plan the work around the area that needs attention. Account for this preparation before your next driving session, so you start your cockpit changes with a clear picture of what fitting the riser involves.
  • PLAN YOUR ASSEMBLY — Two M4 screws were used to hold the riser together, giving you a starting point when planning the assembly for your racing seat. Have your fitting plan ready before taking time away from your simulator to change the pedal position. Hardware required (not included): 2 × M4 screws (holding riser together). WHAT\'S IN THE BOX — Only the item named in the title. No hardware is included (see the description).

Your pedals sit lower than you want, and their angle does not suit the way you sit. You want to change the position at your feet, not start over with a different racing seat.

The SplashNColor pedal riser raises the pedal assembly on your racing seat to give it a better angle relative to you as the driver. It puts the change at the pedals, where your feet meet the controls. When you settle into your seat for a drive, the pedal position determines how those controls line up with you; raising the assembly changes that relationship.

The riser is 168 mm high. Check that measurement against the space around your pedal assembly as you plan your cockpit layout, and consider the raised position in relation to where you sit. This is the height of the riser, giving you a concrete dimension to work with before you begin fitting it.

Installation involves trimming a small amount of foam around the pedal tubes. Plan for that preparation when you work on your racing seat, before moving on to assembly. Two M4 screws were used to hold the riser together, so take that assembly detail into account as you plan the work.

This riser is for sim-racing users who want to change the pedal position in their home racing-seat setup. Whether you are getting your cockpit ready for an evening drive or revisiting the layout after time behind the wheel, it keeps the change centered on the pedals and their angle.

HARDWARE NOT INCLUDED: Only the item named in the title is in the box. Every setup is different: depending on yours, mounting it or attaching it to an existing part may use hardware you already have, such as the original screws, or you may need to buy your own screws, bolts, tape or adhesive to suit your situation. No hardware of any kind is included with this listing.

Hardware required (not included): • 2 × M4 screws (holding riser together)

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design