Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

POWERTEC 71868 Guide Rail Splinter Guard Replacement Strip 55"

POWERTEC 71868 Guide Rail Splinter Guard Replacement Strip 55"
$15.99

Buy Now

POWERTEC 71868 Guide Rail Splinter Guard Replacement Strip 55\" — For POWERTEC 71387, Festool, Makita 194419-4, DeWalt POWERTEC USA 55\" ROLL • 0.078\" THICK PE • SELF-ADHESIVE BACKING • ZERO-TOLERANCE INSERT • FITS POWERTEC 71387 • FESTOOL • MAKITA 194419-4 • DEWALT Guide Rail Splinter Guard Replacement Strip 55\" — POWERTEC 71387, Festool, Makita 194419-4, DeWalt (71868) Your Track Saw Cuts Are Only as Clean as Your Splinter Guard. Time to Replace It.

The splinter guard on a guide rail is the narrow PE strip that runs along the saw-side edge of the rail. When it\'s in good condition, it acts as a zero-tolerance insert — the strip material closes the gap right at the blade path, so your workpiece fibers are supported all the way to the cut line and the blade exits cleanly on both sides. When it\'s compressed, torn, or worn from accumulated cuts, that support disappears. The gap opens up, fibers lift before the blade reaches them, and what was a clean 90° veneer cut becomes a ragged tearout line on the show face. The POWERTEC 71868 is a 55\" roll of 0.078\" thick PE replacement strip with a self-adhesive backing — peel the old strip off, clean the channel, and press the new one in. The cut quality of a fresh guide rail installation, for the cost of a replacement strip.

The 71868 fits the POWERTEC 71387 guide rail as its primary application, and also serves as a direct replacement for the splinter guard strips used on Festool guide rails, Makita 194419-4, DeWalt, and other guide rail systems that use a compatible-dimension PE adhesive strip in the same channel position. At 0.078\" thick, this strip provides genuine resistance to compression from repeated cuts — it doesn\'t flatten out after a few sessions the way thinner-material strips do.

At a Glance 55\" Strip Length (Roll) 0.078\" Thickness — Thick PE Peel & Stick Self-Adhesive Backing PE High-Quality Polyethylene What a Splinter Guard Actually Does — And Why It Needs Replacing The Zero-Tolerance Insert: How It Works ❌ Worn or Missing Splinter Guard

When the strip is compressed, torn, or absent, a gap opens between the rail edge and the blade path. Wood fibers on the show face are unsupported ahead of the blade — they flex and lift before the blade reaches them, then tear rather than cut cleanly. Results: feathered edges, chip-out on the show face, and ragged grain on veneered panels or hardwood tops. No matter how sharp the blade, a degraded splinter guard limits cut quality on the lower face of the material.

✅ Fresh Splinter Guard (This Strip)

A properly installed PE strip closes the gap entirely — the strip material supports the workpiece fibers right up to the blade\'s exit path. Fibers are held against the surface until the blade passes through them, producing a clean, supported cut on both faces. This is the condition the track saw was designed to operate in. The \"zero tolerance\" name refers to this zero-gap between strip edge and blade kerf — no unsupported fiber zone, no tearout.

The splinter guard is a consumable — it gets cut through with every pass. Replace it when you see fraying, compression, or gap opening at the blade path. A 55\" roll covers one full re-strip of a standard guide rail with length to spare for re-trimming as needed.

Guide Rail Compatibility — OEM Part Numbers Brand / System Model / Part Number Compatibility POWERTEC 71387 Track Saw Guide Rail Primary Fit Festool FS 1400/2, FS 1900/2, FS 2700/2 Guide Rails (and compatible Festool rail system) Compatible Replacement Makita 194419-4 Guide Rail Compatible Replacement DeWalt Guide Rail System Compatible Replacement Other Brands Any guide rail using a compatible-dimension PE self-adhesive splinter guard strip Verify strip width and channel dimensions before installing Three Reasons This Strip Performs 📏 0.078\" Thickness — Built to Last

At 0.078\" thick, this PE strip resists compression from repeated cuts far longer than thinner-material strips. Thin strips flatten against the channel floor after a season of use — the surface compresses down and the gap reopens. Thickness is what keeps the zero-tolerance function working through actual sustained shop use.

🏷️ Self-Adhesive — Peel and Stick

No adhesive to source, no waiting for contact cement to tack, no clamping. The factory-applied adhesive backing bonds to the guide rail channel — clean the channel surface, peel the liner, press the strip in. One of those tool-maintenance tasks that takes 10 minutes when the right product is in the shop and 45 minutes when you have to improvise with whatever adhesive is on the shelf.

🔁 55\" Roll — Full Rail Coverage

At 55 inches, this roll covers a standard guide rail with length to spare. The extra length allows you to cut the strip slightly long, press it in, then trim flush with a sharp knife at the ends — a cleaner installation than cutting to exact length and trying to position it perfectly from a stopped end. Use the overage to replace just the most-used section of a partially worn strip.

Installation — Peel and Stick Replacement
  1. Remove the worn strip: Peel or lift the existing splinter guard from the guide rail channel. A plastic scraper or fingernail works — avoid metal tools that could score the aluminum channel floor.
  2. Clean the channel: Remove any remaining adhesive residue from the channel surface. Isopropyl alcohol on a cloth cleans both adhesive residue and sawdust from the channel — let it dry fully before proceeding.
  3. Cut the strip slightly long: Cut the new strip 1–2\" longer than the rail channel. Easier to trim flush than to try to position a cut-to-length strip exactly.
  4. Peel the backing and press in: Starting from one end of the channel, peel a few inches of backing and press the strip into the channel, working along the length. Press firmly to ensure full adhesive contact — a roller or the flat of your thumb works well.
  5. Trim flush at the ends: Once the strip is fully seated, trim the overhanging ends flush with a sharp utility knife or chisel.
  6. First cut initializes the strip: Run the guide rail and saw through a piece of scrap to cut the new strip to the exact blade path width. This is normal — the strip is designed to be cut through on first use, establishing the zero-tolerance fit for your specific blade.
Key Product Benefits:
  • Zero-Tolerance Insert Function: PE strip closes the gap at the blade exit path — supports workpiece fibers right up to the cut line, preventing chip-out and tearout on the show face.
  • 0.078\" Thick High-Quality PE: Greater resistance to compression than thin-material strips — maintains zero-tolerance function through sustained use rather than compressing flat and losing effectiveness.
  • Self-Adhesive Backing — Peel and Stick: Factory-applied adhesive eliminates the need to source and apply separate contact cement — clean, peel, press, and trim in minutes.
  • 55\" Roll — Standard Rail Length Coverage: Sufficient length to re-strip a standard guide rail with extra for end trimming and targeted replacement of highest-wear sections.
  • Multi-Brand Compatibility: Fits POWERTEC 71387 guide rail as primary application; also a compatible replacement for Festool, Makita 194419-4, DeWalt, and other guide rail systems using PE adhesive splinter guard strips.
  • Tool-Free Installation: No special tools, no adhesives to source. Peel the backing and press it in — serviceable in the shop without interrupting the workflow.
PRO TIP: Before pressing the new strip in, warm the channel with a heat gun or warm shop for 5–10 minutes if your shop is cold. Cold aluminum pulls heat from the adhesive instantly on contact, which weakens the initial bond before it can cure. A warm channel lets the adhesive seat fully and bond more aggressively on the first press — the strip stays flat through the first cutting session rather than lifting at the ends. When to Replace the Splinter Guard Visible fraying or lifting along the strip edge where the blade has cut through repeatedly Strip surface compressed flat — zero-tolerance gap has reopened between strip edge and blade path Tearout appearing on the show face of cuts that previously came off the rail clean Strip delaminating from the channel floor — adhesive worn out from age or accumulated moisture New guide rail setup — installing a fresh strip before first use establishes zero-tolerance fit for your specific blade New blade installed — blade kerf width changes require a fresh strip cut to re-establish tight fit at the new blade path Completing precision cuts on veneered panels, hardwood faces, melamine, or laminate where tearout is unacceptable Product Specifications
  • SKU / Part Number: 71868
  • Includes: 1 Splinter Guard Replacement Strip — 55\" Roll
  • Strip Length: 55 Inches
  • Strip Thickness: 0.078\" (Thick PE)
  • Material: High-Quality Polyethylene (PE)
  • Attachment: Self-Adhesive Backing — Peel and Stick, No Additional Adhesive Required
  • Primary Compatible Rail: POWERTEC 71387 Track Saw Guide Rail
  • Also Compatible: Festool Guide Rail System, Makita 194419-4, DeWalt Guide Rail, and Others
  • Function: Zero-Tolerance Insert — Prevents Splintering at Track Saw Cut Line
  • Installation: Peel Liner, Press Into Channel, Trim Ends Flush — Tool-Free
More POWERTEC Guide Rail & Track Saw Accessories
  • POWERTEC 71542 — 7\" Table Clamp for MFT and Guide Rail System, 2PK: Clamping system for securing guide rail to workpiece on MFT tables and work surfaces — for track saw operation without a dedicated rail clamp
  • POWERTEC 71411 — 60\" Premium Guide Rail Bag with Dual-Sided Padding: Protective storage and transport bag for 60\" guide rails — padded interior prevents rail surface and splinter guard damage during storage and job site transport
  • POWERTEC 71876 — Woodworking Safety Push Tool Set (Table Saw / Router Table): Push block and push stick set for safe workpiece feeding past table saw blades and router table bits

POWERTEC is a leading manufacturer of high-quality woodworking tools and accessories, machines, and an assortment of OEM replacement parts. We are committed to exceeding expectations while bringing the latest innovations, technology, and product development to the industry.

© 2026 POWERTEC USA. All Rights Reserved.
WARNING: Cancer and Reproductive Harm — www.P65Warnings.ca.gov

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design