Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

Mini Wireless Remote Control Switch DC 6V 12V 24V 48V 60V 1CH Channel RF Relay S

Mini Wireless Remote Control Switch DC 6V 12V 24V 48V 60V 1CH Channel RF Relay S
$20.47

Buy Now

  • 433 Mhz universal wireless remote control switch: input voltage DC 5~60V, working mode is superheterodyne.
  • Transmission distance: about 50~100m (open space), if the transmission distance is not ideal, the antenna inside the receiver box can be pulled outside through the round hole of the box, which will be more conducive to reception.Support remote control type: EV1527 learning code. Supports up to 20 remote controllers (if the remote controller is lost, buy one to pair with the PCB board.)
  • PCB size: 47 x 26 x 18 mm (L,W,H), output terminals: NO , NC , COM.
  • It supports remote and wireless control of your car battery power, garage doors, electronic doors, appliances and other remote control devices, appliances, motorcycle alarms, car sunroofs, heating systems, and more. Bring you a brand new remote control experience, please don't miss it.
  • EASY TO USE: There are 4 function modes: Momentary, Toggle, Latched and Delay Modes, please refer to the details page below for pairing.
  • You can configure momentary mode for access control; You can configure latched mode for turning on/off car battery power.

Product description DC 5~60v Single Channel Controller Technical Parameters

Working Voltage : DC 5V/6V/12V/24V/36V/48V/60V

Modulation Mode:ASK

Matching Mode: Intelligent Learning Code 1527.

Quiescent Current:5mA

Maximum load power: 300W

RF Frequency: 433MHz

Wiring method: NC COM NO

Circuit Board Size: 26 * 47 * 18mm

Output: single-channel passive switch quantity output

Max Relay Contact Current : DC 20A/AC 5A

About what is dry contact and how to wire it

This is a passive output dry contact relay module, the COM, NO and NC terminals together form the ‘dry contact’, they are simply the three pins of the relay contact and do not carry any internal voltage or power supply of their own.

In order to generate ‘voltage’/‘current’ between the output terminals, an external power supply must be connected, which does not supply power to the controller, but to the load. When COM and NO are connected with the remote control control, the external current can pass through and the load starts working.

About Working Modes Momentary

Press the remote button , the relay connects, release the remote button , the relay dis-connects.

Momentary mode can be applied to electric door locks!

Toggle

Press once the remote button, the relay connects , press the remote button again, the relay dis-connects .

Latching

Press the remote button ON, the relay connects, press the remote button OFF, the relay dis-connect.

We recommend using the Latching Mode, which uses one button for ON and one button for OFF.

Latched mode can be applied to on/off car batteries!

Delay Mode

Press the remote button , the output terminal of the receiver will be powered on for a certain time (5s/10s/15s/20s), and the output terminal of the receiver will be powered off.

Working Mode Settings

1.Reset : Press the learning button on the module 8 times continuously, and the light flashes seven times and then goes out.

2.Momentary Mode:Press Module learning button 1 time, the indicator light is always on, then press the remote control button, the indicator light flashes 3 times and then turns off , then the learning is successful; If the code is not successful , the indicator lights out of the learning state after 15 seconds .

3.Toggle Mode:Press the Module Learning button 2 times, the indicator light always turns on; then press the remote control button, the indicator lights flicker three times and then off, then the learning is successful; if the code has not been successful, the indicator lamp goes out of the study state after 15 seconds.

4.Latched Mode :Press the receiver button 3 times, the receiver indicator light is always on, the receiver enters the code matching state, and then press the remote control button, the receiver indicator light flashes and then stays on, then press another button on the remote control, after the code is successful, the indicator light goes out.

5.Delay Mode : Press a certain number of times (4 times correspond to 5s/ 5 times correspond to 10s/ 6 times correspond to 15s/ 7 times correspond to 20s) to press the receiver button, the receiver indicator light is always on, the receiver enters the code matching state, then press the key of the remote controller, and the indicator light will go out after the code matching is successful.

Regarding how to switch work modes and whether a reset is required:

Please note that if you wish to pair multiple remote controls with the same relay, simply pair each remote control with the relay one by one. Do not reset the relay during this process, as doing so will erase all paired remote control data.

Conversely, if the remote control is already paired but you wish to change its operating mode, you must first reset the relay and then re-pair it to successfully change the mode.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design