Honeywell R7140G1000 Burner Control Module – Flame Safeguard / Combustion Control
GenuineHoneywell R7140G1000 Burner Control Module, a microprocessor-based integratedburner control and flame safeguard controllerdesigned for automatically firedgas, oil, and combination-fuel single-burner applications.
The Honeywell R7140 series provides automatic burner sequencing, flame supervision, safety interlock monitoring, system status indication, self-diagnostics, and troubleshooting functions.
TheR7140G1000is designed for commercial and industrial combustion systems where dependable control of burner startup, pre-purge, ignition, pilot flame establishment, main flame operation, safety interlocks, and shutdown sequencing is required.
Key Features
- Model / MPN:R7140G1000
- Type:Burner Control Module / Flame Safeguard Control
- Microprocessor-based burner management control
- For gas, oil and combination-fuel burner applications
- Automatic burner sequencing
- Flame supervision and flame failure protection
- Pilot ignition and main flame sequencing
- Safety interlock monitoring
- Built-in system diagnostics
- Sequence/status LED indication
- Run/Test functionality
- Interchangeable plug-in flame amplifier design
- Plug-in ST7800 purge timer card system
- Nonvolatile operating history and sequence memory
- Compatible with Honeywell Q520A 20-terminal wiring subbase
- Optional S7800 Keyboard Display Module support
- 120 VAC, 50/60 Hz
Honeywell specifies the R7140 series for120 VAC (+10%/-15%), 50/60 Hz, with maximum run-mode power consumption of 10 W and maximum total connected load of 2000 VA.
Configuration Jumpers – R7140G1000
The label on thisR7140G1000identifies three configurable functions:
JR1 – Pilot Flame Establishing Period
Intact:10 seconds
Clip & Remove:4 seconds
JR2 – Pilot Valve
Clip & Remove:Interrupted
JR3 – Airflow Switch Check
Intact:Disabled
Clip & Remove:Enabled
The jumper configuration should always be verified for the specific burner and combustion application before installation or operation.
Flame Detection Compatibility
The Honeywell R7140 platform works with interchangeable plug-inflame signal amplifiers, allowing the burner control system to be configured for different flame detection technologies.
Depending on the installed amplifier and application, the R7140 platform supportsflame rod / rectification, ultraviolet (UV), infrared (IR), and optical flame detection. Honeywell documentation lists amplifier families includingR7847, R7848, R7849, R7861, R7886 and R7851.
This makes the R7140G1000 useful in a wide variety ofboiler flame safeguard, industrial burner management, HVAC combustion control and process heating systems.
Replacement / Retrofit Applications
The Honeywell R7140 family was designed as a replacement platform for many legacy Honeywell burner controls.
Honeywell states that R7140 Burner Control Modules can directly replace manyBC7000 PM720, R4150G/L/M and R4140G/L/Mcontrols while utilizing the existingQ520A 20-terminal wiring subbase, subject to proper model selection and wiring configuration.
This makes theHoneywell R7140G1000particularly valuable for maintenance, repair and retrofit of older commercial and industrial burner installations.
Typical Applications
Common applications may include commercial boilers, industrial boilers, gas burners, oil burners, dual-fuel burners, furnaces, process heaters, HVAC heating equipment, combustion systems, burner management panels and industrial heating equipment.
The controller can coordinate critical burner functions includingburner/blower motor operation, ignition, pilot valve operation, main fuel valve operation, flame proving, operating limits and safety interlocks.
Electrical / Environmental Specifications
Supply:120 VAC (+10% / -15%)
Frequency:50/60 Hz
Power Dissipation:10 W maximum in Run mode
Maximum Connected Load:2000 VA
Operating Temperature:-40°F to +140°F (-40°C to +60°C)
Storage Temperature:-40°F to +150°F (-40°C to +66°C)
Humidity:Up to 85% RH, continuous, non-condensing
Mounting:Q520A 20-terminal wiring subbase
Honeywell lists these electrical and environmental ratings for the R7140 platform.
Honeywell R7140G1000, R7140 G 1000, Honeywell R7140G, Honeywell burner control module, burner control relay, Honeywell flame safeguard, flame safeguard controller, burner management control, combustion control module, combustion safety control, industrial burner controller, gas burner control, oil burner control, dual fuel burner control, boiler burner controller, boiler flame safeguard, commercial boiler control, industrial boiler control, burner sequence controller, ignition control module, pilot flame controller, main flame control, flame supervision system, flame safety controller, Honeywell 7800 Series, Honeywell Q520A, Q520A subbase, Honeywell ST7800, ST7800 purge timer, Honeywell R7847, R7848, R7849, flame amplifier, UV flame detector control, flame rod control, Honeywell R4140 replacement, R4140G replacement, R4150G replacement, BC7000 replacement, PM720 replacement, industrial HVAC controls, boiler replacement parts, burner replacement parts, combustion equipment control.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.