Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

Hitch Tightener Anti Rattle Clamp 2 Inch Receiver Stabilizer Trailer Heavy Duty

Hitch Tightener Anti Rattle Clamp 2 Inch Receiver Stabilizer Trailer Heavy Duty
$39.55

Buy Now

Zoyowic Stop the Clunk in Your Hitch A 2″ receiver and a 2″ shank are never a tight fit. This clamp takes up that gap — 1/2″ steel bracket, two 5/8″ bolts, two rubber silencer pads. About two minutes to install. 2″ receiverUniversal fit 1/2″Steel bracket 5/8″Bolts + jam nuts Why your hitch rattles at all A receiver tube is 2″ nominal, and the shank sliding inside it is always slightly undersized so it can go in at all. That clearance is by design — and it is also the clunk you hear every time you cross a bump, the wobble you feel at highway speed, and the slow wear that polishes the inside of the tube. Tightening the pin does not fix it, because the pin only stops the shank from sliding out, not from rocking. What this clamp does It presses the shank hard against the inside wall of the receiver, so the two pieces become one. The play is gone, and with it the noise and the wear. Will it fit your setup? Look at the receiver tube on your vehicle before ordering — the bracket needs a clean, exposed lip to clamp against. Your receiver Note Fits Standard 2\" x 2\" receiver (Class III / IV)Fits — this is what it is made for✓2.5\" receiver (Class V heavy duty)Tube is too large, clamp will not seat✗1.25\" receiver (Class I / II)Needs the 1.25\" version✗Receiver with a welded or reinforced collarNo clearance around the opening for the bracket lip✗Hidden hitch (tube ends behind the bumper)Nothing to clamp against at the mouth✗Receiver with a heavy weld seam at the mouthSeam blocks the bracket from sitting flat✗ Commonly used on: F-150, Silverado, Sierra, Ram 1500, Tacoma, Tundra, Wrangler, most SUVs and crossovers, RVs, boat trailers and utility trailers — anything with a standard 2″ × 2″ receiver and an exposed lip at the opening. The one thing that catches people out If the opening of your receiver is surrounded by a welded collar, a reinforcement plate, or sits behind a bumper with no exposed lip, there is nothing for the bracket to clamp against and this part will not work. Walk out and look at your hitch first — it takes ten seconds and saves a return. What you are getting Built to be bolted on once and forgotten about. 1It removes the slack, not the strengthA 2\" receiver is 2\" nominal. The shank that slides into it is always a little smaller, and that clearance is the clunk you hear. This bracket clamps the shank against the inside wall of the receiver so it cannot move. It carries no load itself, so your hitch\'s rated towing capacity is unchanged.21/2\" thick bracket, 5/8\" bolts, jam nutsThe clamp is cut from 1/2\" steel and finished in red powder coat. Two 5/8\" threaded bolts do the clamping, and each one gets a jam nut so vibration cannot walk it loose on a long drive.3Two rubber pads kill the metal-on-metal contactThe kit includes two flat rubber silencer pads. They sit between the shank and the receiver wall, so the surfaces are separated by rubber instead of grinding against each other mile after mile.4Fits anything that slides into a 2\" receiverBall mounts, drop hitches, bike racks, cargo carriers, tow bars, winch plates, ATV and boat trailers. If the shank is 2\" square, this clamp goes on it — no drilling, no welding, no vehicle-specific part number.5Stops the wear that shortens receiver lifeLong-term shaking polishes the inside of the receiver bore and enlarges the pin holes. Taking the play out at the source is cheaper than replacing a receiver later. Fitting it 1Slide the bracket onto the shankPush the square opening of the red bracket over the end of your ball mount or accessory shank.2Insert into the receiverPut the shank into the 2\" receiver and line up the pin holes. Insert your hitch pin as usual.3Tighten the two boltsRun both 5/8\" bolts down until they press the shank firmly against the receiver wall, then lock each one with its jam nut. Re-check after the first few miles. Specifications Fits receiver size2\" x 2\" (standard Class III / IV)Clamp thickness1/2 inBolt thread5/8 in, with jam nutsSilencer pads2 x rubber, includedMaterialSteelFinishRed powder coatInstall timeAbout 2 minutes, one wrenchDrilling / weldingNone requiredNet weight3.3 lbPackage size5.9 x 4.5 x 3.3 in In the box • 1 × red powder-coated clamp bracket (1/2″ steel)
• 2 × 5/8″ bolts
• 2 × 5/8″ jam nuts
• 2 × rubber silencer pads A note on what this part does not do It does not increase your towing capacity, and it is not a substitute for a weight-distribution setup or sway control. It takes slack out of the connection so the hitch stops moving around — that is all, and it is the thing most people are actually trying to fix. Check the bolts after the first few miles of towing, and again at the start of each season. Zoyowic — 2″ Trailer Hitch Anti-Rattle Tightener. Model KEJ-SKD-CD2. UPC 751678141983. Fits standard 2″ x 2″ receivers with an exposed lip. 2-year manufacturer warranty.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design