Friction-Type High-Speed Automatic Paging Machine with Conveyor Variable Speed

Friction‑Type High‑Speed Paging Machine · Tech Spec Friction‑Type High‑Speed Automatic Paging Machine with Conveyor Variable Speed Product Overview

The friction type paging conveyor is mainly used for automatic paging of sheet products with various thicknesses and various materials, such as scraps of paper, name cards, labels, cards of various materials, telephone cards, IC cards, IP cards, game rechargeable cards, plastic composite packaging bags, paper box pieces and paper bags. It can separate a pad of sheet products into independent pieces, and convey them one by one, thus to let the ink jet machine to spray codes piece by piece or for other uses. Photoelectric sensor may be installed to count products. It can also be set to shut down when a certain quantity is reached. The friction type paging conveyor can be widely applied to the industries of food, medical, daily chemical, printing, packaging, cosmetics, etc.

Product Parameters Power supplyInput voltage: 110V
Output voltage: 220V
(Note: The machine voltage is 220V. There is a 110V-to-220V transformer included in the packing list. It can convert the 110V power into the 220V power for the machine.) Machine power200W Applicable product rangeLength: 70-320mm (2.7-12.6 inches), adjustable
Width: 80-280mm (3.1-11 inches), adjustable
Thickness: 0.02-5mm (0.0007-0.2 inch), adjustable Precaution

• 1. Before use for the first time, the operator shall read through the manual carefully.
• 2. Before connecting the machine to power supply, the machine shall be checked to have the power switch at [off] status. Then please operate the machine according to the steps instructed on the user manual.
• 3. If the machine would be stopped and not used for a long time, please clean it with dry cloth. Do not use corrosive cleanser while cleaning the machine.
• 4. It is forofferden to splash fluid into inner parts of the electric cabinet for it may corrode or result in short circuit of internal electrical elements.
• 5. Please check the appearance of the machine to guarantee no deformation, damage or rust, and all shafts shall be able to rotate flexibly without blocking.
• 6. The machine is designed as single-phase AC 220V, and the power line is equipped with a 3-line flat plug, which shall be connected to a 3-pin socket with earth wire. The machine is equipped with a 110V-to-220V transformer, and the machine can normally operate after being connected to the 110V power supply through the transformer.
• 7. Conveying speed range: 20~50Hz. The too slow speed can easily result in motor heat and damage.
• 8. For the parameters of the inverter of the machine, all parameters, except the motor speed (frequency), shall not be adjusted by yourself, for it may be hard to reset and the machine may not run normally.
• 9. Please do not start the motor if no article is placed on the machine for paging, thus to avoid long-time friction between the pressing leather and the paging belt which may shorten the service life of the machine.

Product Features Control Panel The control panel integrates the power switch, stop switch and frequency converter – easy to operate. The frequency converter adopts a knob and digital display, facilitating frequency adjustment and display. Motor High‑quality motor provides stable driving force, ensuring paging and conveying operation is smooth, improving efficiency and reducing maintenance cost. Paging Mechanism Separates multiple materials into pieces, adjustable for various specifications, with high paging efficiency and reliability. Conveyor Belt Wear‑resistant and flexible, conveys separated products continuously and smoothly; high stability and long service life. Supporting Frame Stainless steel material improves structural strength and stability; resistant to rust and corrosion, easy to clean and maintain. Supporting Legs Height‑adjustable, keep machine body stable and balanced, greatly reduce vibration during operation, convenient to use and replace. Operation Method

• 1. Connect the power cable to the single‑phase power supply (with good earth wire).
• 2. Press down the general power supply switch on the operating panel, then the inverter is on.
• 3. Adjust the paging width. Adjust the space between the left and the right guide pieces according to the product width. The space shall be 0.5‑1mm wider than the product, and the center of the product shall be aligned to the center of the guide belt. Then screw down the bolts of the front and back guide pieces.
• 4. Feed the products. Put a pad of products (no adhesion) onto the paging assistant plate between the left and right guide pieces, make them as a slope inclined backwards and push them into the baffle plate position.
• 5. Adjust the paging pressure. Adjust the interval and pressure between the pressing leather and the paging belt to separate products without overlapping or blocking. (Factory adjustment usually omits this step.)
• 6. Run/Stop. Connect to power, press green button, lamp turns on; screw off red emergency stop, rotate black knob clockwise to adjust frequency. Belts rotate to perform automatic paging.
• 7. Adjust the speed. Rotate the black knob on the inverter to increase or reduce speed; displayed frequency value changes accordingly.
• 8. Shutdown. Press red stop switch, then press green power supply switch, finally pull out the plug.

Product Display Item Included (230618): 1 x Automatic Paging Machine with Conveyor 110V Shipping & Handling Details

Default Shipping Cost or Free Shipping Information:
▲ Default shipping cost or free shipping service is only for the lower 48 United States by UPS Ground or USPS. Other areas or needs other shipping ways, please contact us.
▲ Buyers from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska, Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there WILL be extra shipping costs, please contact us for more detailed information.
▲ Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer.

Handling Time: Shipping is usually made in 1‑3 business days after payments cleared. Orders are processed from Monday‑Friday; Not on the weekends & public holidays.

Sales tax/Customs duties: Any sales taxes or Customs duties are not included. If came out, they must be undertaken by the buyer.

Damage In Shipping: Email or call us First! We will work with you to get the case resolved in the fastest method.

Return / Refund

If you are not 100% happy with your purchase, please contact Us. Please don\'t directly opened a request or case without informing us, or else, we will do some discounts on the warranty and other sales‑services later on. Hope for your understanding.

Returns & Exchanges
▲ All returns must be made within 30 days of delivery date. Items must be in new, unused condition, with all original materials included. A partial refund may be applied for opened or damaged items, depending on the condition.
▲ Items returned under the buyer’s remorse: The return shipping fee must be covered by the buyer; The original shipping cost will also be deducted from the refund. 15% restocking fee of the items purchase price will be charged.
▲ Returns that are the result of our seller\'s error: Buyer will receive a full refund of the item as well as shipping charges
▲ All returns require a RA (Return Authorization) number that will be given by our seller. Please contact with us at first for more details.

Defective & Damaged Products
▲ If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it\'s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. Hope for your understanding.
▲ Replacement or refund of defective or damaged products can only be returned in exchange for the exact same product, or else, the purchase price will be refunded back to your original payment method.
▲ If an item is received damaged, customer service must be contacted within 7 days of receiving your item. All returns require a RA (Return Authorization) number as above.

Warranty & response

▲ 6 months\' warranty for the machines, not for the consumables. We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.
▲ Any warranty shipping cost to us is responsible by buyer.
▲ Any shipping cost to buyer is responsible by the seller.
▲ We committee to the customer satisfaction and want to bring you the best purchase experience. If there is any problems, please contact us ASAP. If not, please leave us a positive response as it\'s very important for us. Thanks very much.

On Sep 1, 2026 at 20:19:05 PDT, seller added the following information: