Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

DC10G Engine Manual Start And Stop Controller Genset Parts

DC10G Engine Manual Start And Stop Controller Genset Parts
$58.98

Buy Now

Features:

Controller DC10G is designed as one of the engine manual start controller.
The Hz,Volt, Battery voltage and accumulation time can be displayed through the front face LED screen. This controller is also with various kinds of stop and alarm indications to monitor the genset status.Besides, it can also connect with PC so that parameters can be set through Computer to equip for more different gensets.

Panel introduction:​

1. Indicators

Gen frequencyOver/under speedGen voltageLow oil pressureBattery voltageHigh water temperatureAccumulated timeCharging abnormalEmergency stopOver voltageNote:1) Over speed value will be displayed by flashes after over speed alarm.2) Over voltage value will be displayed by flashes after over voltage alarm.3) Charge failure will be displayed as alarm indication but will not stop the engine.

2. Buttons introduction

Display buttons:Four status switch (gen voltage, gen frequency, battery voltage, accumulated time).Press the PAGE button in 5 sec above under Module on power but stop mode,the frequency can be switched between 50Hz and 60Hz.

Operation:

1. Power on : Switch “0”to “I” till the tube is lighted, In the procession of cranking, over speed indicator will be lighted if the crank is not successful after 45sec.(controller will cut off fuel solenoid’s output and come into protection)

2. Start running: Switch “I ” to “II” till engine started. Once power on the engine, it will be cranked. the controller will come into running status after 8 sec if cranking successfully. Then the controller will monitor the relative parameters and set protection.(the controller will cut off fuel solenoid output and display the alarm status if the genset is stopped.)Please Switch from “I”to “0”.

3. Stop and reset:Switch from “I”to “0” and take off the power.

Parameter setting:

Please connect the module to PC by communication cables and powered on.

1. Alarm setting

  1. Over speed alarm: 1710RPM(Rated 50Hz), 2040RPM(Rated 60Hz), range: 0-4000RPM, when the RPM is over this value and keep more than 1sec, then the controller will alarm and stop.
  2. Over frequency alarm: 57Hz(Rated 50Hz), 68Hz(Rated 60Hz),range:40-80Hz, when the frequency is over this value and keep more than 1 sec, then the controller will alarm and stop.
  3. Low frequency alarm: 20Hz, range: 20-60Hz,when the frequency is lower than the value and keep more than 5sec, the controller will alarm and stop.
  4. Over voltage alarm: 500V, range:50-500v, 500V is set as forofferden. When the voltage is over this value and keep more than 5sec,then the controller will alarm and stop.
  5. Charging failure D- value:6V,range:1-24V, when the different value between charging D+ and Battery B+ is over this value and keep more than 5sec, then the controller will alarm.
2. Display setting
  1. Four Screen self-cycling display: the parameters shall be switched timely according to the interval time setting after choosing this option.
  2. Homepage option: one parameter can be displayed as homepage display after choosing this function. The page will be switched automatically after pressing page change button for a while.
  3. Revert-back delay: the time to revert back to homepage.
  4. Self-cycling display time: the interval time setting.​

​

Technical Specifications:

  • Power supply:8-33VDC
  • Power consumption:MAX 2W(Working
  • Alternator Voltage input:15-300VAC,50/60H
  • Speed input:Freq 300Hz~10kH
  • Fuel output:MAX 16
  • Start output:MAX 10
  • Excitation Output:MAX 80m
  • Alarm output:MAX 16
  • Operating temperature:-30-75
  • Storage temperature:-40-85
  • Pannel cutout:67×67m
  • 1 xEngine Manual Start Controller
  • 2 x Screw
  • 1 x User manual

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design