Compustar 2WR3R-FM 2-Way 1-Button 3000-FT LED Car Starter Keyless Remote Key FOB

This is ONE (1) Aftermarket Installed Original Equipment O.E.M. keyless remote control transmitter vehicle starter.

Compatible with these control modules: CM-900X, CM-DC3, CM-X, CM7000-AS, CM7200-S, CM900-AS, CM900-S, CMBMXA0,

CMVWXA0, SmartKey Starter® for Mercedes-Benz

• 2WR2R-FM 2-way, 1-button remote (up to 3000-ft of range)

Replacement Remote ONLY. You will still need a matching antenna, Arctic Start 2WR2R-FM 2-Way 1 Button Remote Control SAME AS Compustar 2WR3R-FM
Arctic Start 2WR2R-FM 2-Way 1 ButtonRemote Control SAME AS Compustar 2WR3R-FM

• 2-way LED command confirmation
• Up to 3000 feet of range
• 
  
• DroneMobile Compatible
• Requires Antenna ANT-2WFMX ( not included )
• Communication Method: Frequency Modulation (FMX)

Remote Start

Hold down the main button for 2.5 seconds to remotely start your engine to heat up/cool down your vehicle.

Keyless Entry

Single tap on the button to perform a LOCK command or a double tap to UNLOCK.

and a Compustar system in your vehicle to be able to program this remote. Command specific LEDs Water-resistant remote casingRemote StartHold down the main button for 2.5 seconds to remotely start your engine to heat up/cool down your vehicle.Keyless EntrySingle tap on the button to perform a LOCK command or a double tap to UNLOCK.Dealer part #Compustar 2WR2R-FM 2-Way 1 ButtonButtons1; Engine Start/ Stop; Orange LED LightFrequencyPairing the fob to your compatible installed system:
Programming 1 Way 4 Button Remotes:
STEP 1: Activate Valet/Programming mode by manually turning the ignition key on and off (between the
Acc & On positions) five times within 10 seconds. The vehicle s parking lights will flash once with the
successful completion of this step.
STEP 2: Within 2 seconds after cycling the ignition for the 5th time, tap the button on ANT-2WFMX or
ANT-1WFMX for a half second. The Red LED on the Antenna will turn on.
STEP 3: Tap the Lock button on the 1st remote for a half second. The Green LED on the Antenna will
flash 1 time. The parking lights will also flash once to confirm the remote has been programmed. Repeat
this step for additional remotes.
Exiting Programming: Programming is a timed sequence. The parking
lights will flash twice signaling the end of programming mode.
Programming Multiple Remotes: Code additional remotes by
pressing the Lock button on 2 way remotes or the Lock button on 1
way remotes. The parking lights will flash once confirming each
additional remote. All compatible systems can recognize up to 4
remotes.
Programming Remotes on Push to Start (PTS) Vehicles
Most Push to Start vehicles do not have a key that you can turn between the On and Acc positions. This
makes programming remotes difficult. We have a different set of steps for programming remotes.
STEP 1: Press the PTS button to turn the vehicle to the On position. Do not start the car.
STEP 2: Within 5 seconds, push the PTS button again to turn the vehicle Off.
STEP 3: Within 5 seconds, push the PTS button to turn the ignition On.
13
STEP 4: Within 5 seconds, press and release the foot brake 3 times. The parking lights will flash once to
indicate remote programming has begun.
STEP 4A (FMX REMOTES ONLY): If using one of the FMX frequency remotes, you will need to
tap the button on the antenna after the 3 foot brake presses in STEP 4. The front LED on the
antenna will turn on solid red. After the antenna s LED illuminates solid red, proceed to STEP 5.
STEP 5: Tap the lock button on the 1st remote. The LED on the antenna will flash green. The parking
lights will also flash once, indicating that the remote has been coded. Repeat this step to code each
remote, pressing the lock button one after the other.
STEP 6: After 10 seconds, your vehicle will exit remote programming modeBattery Type2: CR2025