CANBed - Arduino CAN-Bus RP2040 development board NEW

CANBed - Arduino CAN-Bus RP2040 development boardModel: 102991596 Product Description

Implements CAN V2.0B at up to 1 Mb/s
Industrial standard 9 pin sub-D connector or 4PIN Terminal.
OBD-II and CAN standard pinout selectable at the sub-D connector
2x4Pin Connector compatible with Grove system from
SPI Interface
Standard (11 bit) and extended (29 bit) data and remote frames
Power input from 9-28VDescription
The CANBed RP2040 version has been changed from V1.0 into V1.1. For further information, please check here.
CANBed RP2040 is a CAN Bus development board equipped with an RP2040 chip with a high-performance MCP2515 CAN controller and MCP2551 CAN receiver operating at CAN2.0 protocols in 133MHz. The board contains a flexible CAN interface where it can be used 4-PIN Terminal or D89 connector. D89 connector can be directly used as OBD-II mode by default and the hardware can be configured as CAN Open mode as well. Additionally, it has a rich interface in which there is a Micro USB connector that can be programmed instead of supplying power. It also has I2C, UART, SPI, 3 analog input interfaces, and 8 digital IO with 2MB of Flash and 264KB of RAM which make it suitable for most embedded applications.
If you want to use this board to develop OBD-related applications, click to get a DB9 to OBD-II cable.
We use a flexible way for the CAN interface. You can use 4PIN Terminal or DB9 connector. DB9 connector uses OBD-II mode by default. You can also configure CAN Open mode on the hardware. The voltage input range of the CAN interface is 9-28V, which can provide a stable 3.3V/1A Speed
flexible clock running up to 133 MHzFlash Memory
2MBRAM
264KBOperate Voltage
9-28VOutput Current @ 3.3V
1AInput Interface
sub-DApplicationHack and Upgrade Your Car
Vehicle dynamics control system
Attitude and orbit control systemHardware Pinout1. GPIO - 9x2 I/O Pin OUT:2. Micro USB connector for programming3. SPI Interface4. CAN RX/TX Indicator5. DB9 connector or Terminal for CAN Bus6. Switch for the 120Ω terminal resistor for CAN Bus7. Grove connector for UART8. Grove connector for I2C (Wire1)9. ResetCAN Bus Family inCAN-BUS series product selection reference is provided here. The table compares NEW-Release Wio-E5 CAN, CANBed v1, CANBed FD, CANBed M4, and CANBed RP2040 in terms of MCU, protocol, memory, interface, etc.ItemsWio-E5 CANCANBed v1CANBed FDCANBed M4CANBed RP2040CANBed DualMCUWio-E5 (STM32WLE5JC)ATmega32U4(with Arduino Leonardo bootloader)ATmega 32U4 (with Arduino Leonardo bootloader)ATSAME51 32bit Cortex M4 coreRP2040(Dual ARM Cortex-M0+)RP2040
(Dual ARM Cortex-M0+)Clock Speedup to 48MHz16MHz16MHz120MHzup to 133 MHz133MHzProtocolLong Range,RS485,CANFD & CAN2.0CAN2.0CANFD & CAN2.0CANFD & CAN2.0CAN2.0CANFD & CAN2.0Flash Voltage （MicroUSB）5V5V5V5V3.3V5VLipo Battery3.7V-----Input Interface9 pin sub-D or 4PIN Terminal9 pin sub-D or 4PIN Terminalsub-D or 4PIN Terminalsub-D as well as ListCANBed 2040 PCBA
x1Sub-D connector
x14PIN Terminal
x14PIN HY2.0 Connector
x29x2 2.54 Header
x13x3 2.54 Header
x1Switch for 120Ω terminal resistor
x1

📦 Brand New 🛡 Manufacturer Warranty 🚚 Ships with Tracking

Thank you for shopping with us! Questions? Send us a message.