Arduino DRV8825 stepper motor driver Module 3D printer RAMPS1.4 RepRap StepStick

Arduino DRV8825 stepper motor driver Module 3D printer RAMPS1.4 RepRap StepStick

This module is blue PCB now,please know it .The DRV8825 stepper motor driver carrier is a breakout board for TI\'s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications.
The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
1）Simple step and direction control interface
2）Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
3）Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor\'s rated voltage to achieve higher step rates
4）45 V maximum supply voltage
5）Built-in regulator (no external logic voltage supply needed)
6）Can interface directly with 3.3 V and 5 V systems
7）Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
8）Short-to-ground and shorted-load protection
9）4-layer, 2 oz copper PCB for improved heat dissipation
10）Exposed solderable ground pad below the driver IC on the bottom of the PCB
11）Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information) This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features:

Simple step and direction control interface
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
45 V maximum supply voltage
Built-in regulator (no external logic voltage supply needed)
Can interface directly with 3.3 V and 5 V systems
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
Short-to-ground and shorted-load protection
4-layer, 2 oz copper PCB for improved heat dissipation
Exposed solderable ground pad below the driver IC on the bottom of the PCB
Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information)
We also carry a DRV8824 stepper motor driver carrier that can serve as a direct substitute for the DRV8825 carrier when using lower-current stepper motors. The DRV8824 can only deliver up to 0.75 A per coil without a heat sink (1.2 A max with proper cooling), but it has larger current-sense resistors that allow for better microstepping performance than the DRV8825 carrier at low currents. The only way to tell our DRV8824 carrier apart from the DRV8825 carrier is by the markings on the driver IC; if you have a mix of the two, you might consider marking them (there is a blank square on the bottom silkscreen you can use for this). For lower-voltage applications, consider our pin-compatible DRV8834 carrier, which works with motor supply voltages as low as 2.5 V.
This product ships with all surface-mount components—including the DRV8825 driver IC—installed as shown in the product picture.

Package Included:

1 x Arduino DRV8825 stepper motor driver Module 3D printer RAMPS1.4 RepRap StepStick

• Return Policy

Shipping

Domestic
We believe you need to get your purchases as quick as possible. As a general rule your item will be shipped within 24 hours of you purchasing it. We pack and post from Tuesday to Sunday (Mondays we are closed) but definitely get all our mail off to the post office first thing Monday morning for you. Mail gets picked up at 12pm so chances are if you buy before lunchtime your item will leave the same day.

International
Same as above but understand that depending on what part of the world you are from it does take a little longer to send, delivery can be from 7-15 working days. Also other factors to take into consideration are quarantine and customs regulations in your country. It is also a consideration that customs duties and GST/VAT may be payable at the buyers expense.

Combined Postage (for items with shipping charges):
We are more than happy to combine postage, just use the Buy it Now function in (but DO NOT PAY after purchasing each item) to buy all the products you need, when you have finished request a combined invoice, we will base the shipping cost on the size, weight and your location.

response

* When you satisfied with our product and services please leave us positive response.

* If you have got the package, please confirm \"Delivery on time\" For us.

* If a problem occurs, contact us immediately with any email request.

* Just contact us using the \" Ask the seller a question\" link on .

Your Satisfaction is our Priority. Our goal is to make all our customers as happy as possible while shopping with us.

Contact us

For anything problem about product, price, shipping or order status, pleasecontact us via message.Just contact us using the \" Ask the seller a question\" link on .
We expect positive response and 5 scores DSR from you.

Return Policy

1. We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund to you after the returned item arrived at our warehouse.
3. Please include your ID and item number with any email requests.