Altera MAX 10 FPGA Development Kit - MaxProLogic

MAXPROLOGIC FPGA
DEVELOPMENT SYSTEM

The MaxProLogic is an FPGA development board that is designed to be user
friendly and a great introduction into digital design for anyone.

The MaxProLogic is designed to make digital design easy and cost effective. At
Earth People Technology we have years of experience helping students and
hobbyists get started with FPGA design. We know that the learning curve in
getting started can be a time consuming and frustrating event. So, we created a
User Manual that walks the user from unpacking to creating the first project to
creating an epic project that will get attention.

The core of the MaxProLogic is the Altera MAX10 FPGA. This powerful chip has 4,000 Logic
Elements and 200Kbits of Memory. The MAX10 is easily scalable from the entry
level college student to the most advanced projects like an audio sound meter
with FFT.

Upon the many great features of the MaxProLogic is the MAX10 chip has a built
in Flash for configuration and incorporates 8 channels of Analog to Digital
Conversion. These two features alone create a far superior FPGA chip than any
competitor on the market. It allows the user to create more diverse projects.

MaxProLogic FPGA Development System

• MAX 10 10M04SAE144 FPGA FROM ALTERA
• 4,000 Logic Elements; 2.2 Mbit On chip Flash; 189 Kbit On Chip SRAM
• 8 Analog Input Channels; 12 bit; 1MSamples/Second
• 65 Available I/O’s at connectors
• 8 Green User configurable LEDs
• 1 Power Pushbutton Switch; 1 User Configurable Pushbutton Switch
• On Board SD Card Slot
• Two Power options: Standard USB (+5V @ 2Amp) Using USB-C connector
• 5mm Barrel Connector Accepts +5.5V @ 3Amp
• Switching Power Supply, Provides stable output under high load stress
• One Clock: 50MHz Oscillator
• On board interface to Standard USB to Serial Adapters

Why the MaxProLogic?

The MaxProLogic is designed to make digital design easy and cost effective. At
Earth People Technology we have years of experience helping students and
hobbyists get started with FPGA design. We know that the learning curve in
getting started can be a time consuming and frustrating event. So, we created a
User Manual that walks the user from unpacking to creating the first project to
creating an epic project that will get attention.

The Learning Curve with any new piece of hardware is always time consuming.
We painstakingly crafted a guide that leaves out no details in creating a project
under the Quartus Software Tool. We will explain how to organize project user
files into a folder system for easy navigation. We will explain how to:

• Create a Project
• Add User Files
• Add MegaFunction IP Files
• Add Synopsys Design Constraints,
• Assign Inputs and Outputs to pins of the MAX10
• Compile the Design
• Synthesize the Project
• Program into the MAX10

In short, the MaxProLogic will cut the time to get the time to get up and running
significantly. We also include several pre-made, fully compiled, fully synthesized
projects for the user. You can start your project by copying one of these premade
projects and adding user code.

THE MAXPROLOGIC AND SIMULATION

Simulation has always been a weak point for students and hobbyists. Most
FPGA beginners write the user code, compile it, synthesize it, program the chip
then test out the results. While this approach may work for small, simple
designs, it quickly becomes a problem with larger projects. As the user code
increases in complexity, better development tools are required to quickly
isolate problems. The premier method for this is functional testing. ModelSim is
included Free with the Quartus Prime Package. ModelSim is a powerful tool for
finding errors in the user code before you go to synthesis.

Earth People Technology has created a guide that walks the user through
creating a project and verifying functionality of user code. This guide will
explain the use of the TestBench, Tasks, and Models in verification of the user
code. In specifics, the guide will explain:

• Create a ModelSim Project
• Create a Makefile and Compilation of user code
• Create a TestBench and Stimulus of user code
• Add Synopsys Design Constraints,
• Assign Inputs and Outputs to pins of the MAX10
• Create Models for user code to Interact With
• Add Clock Signals, Resets, and Timing Elements
• Debug the Functionality of user code

PROGRAMMING TOOLS FOR THE MAXPROLOGIC

The MaxProLogic leverages the Quartus Prime Lite Software for compilation
and synethsis. This software tool is completely free and provides very powerful
tools for the user. Also included free in the software tools is the simulation tool,
ModelSim. A lot beginners to the FPGA world are hesitant about using
simulation tools. They feel these tools are too difficult to learn and use. This is
where the MaxProLogic breaks that fear. The MaxProLogic comes with a user
guide that walks the user from start up to full simulation. Each step is well
documented and explained.

THE MAXPROLOGIC HARDWARE

The MaxProLogic is Open Source Hardware based on the
MAX10 FPGA. In addition to the on chip 8 Channel ADC and on
chip Flash, the board is loaded with great tools. The board has
two power options, standard USB Micro B connector and
5.5mm Barrel connector. You can run the MaxProLogic from a
laptop with 2.5W of power. Or you can run it from the +5V @
2A wall USB chargers for 10W of power. The barrel connector
can handle up to +9V @ 3 A for 27W of power.

The MaxProLogic has a MicroSD connector on the bottom of the
board. This allows the user to create a powerful long term
Data Acquisition System. The board has an optional On/Off
pushbutton switch that allows the user to turn the system on
and off. There are two clocking options, 50MHz oscillator and
32.768KHz oscillator.

The block diagram shows all of the parts of the MaxProLogic. There is a
main switching power supply for +3.3V. The +3.3V powers the core of the FPGA
along with the Input/Outputs of the FPGA as well as provides
power for user circuits.

MaxPrologic Communications

The MaxProLogic has a built in connector to allow FTDI Breakout Boards or Equivalent to connect directly to the FPGA. There are two voltage level translators that allow both +5V and +3.3V devices to communicate via UART with the FPGA.

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.