AM Loop Medium Wave
Antenna Kit Frame Box Loop
NEW!!! IMPROVED
by W1VLF
Build your own AM broadcast band receive loop with this 3D-printed spreader kit, designed and printed by W1VLF. Add four short pieces of 3/4" PVC pipe and a PVC cross from any hardware store, wind your wire, and you have a rigid, evenly spaced multi-turn loop that tunes the AM band.
Video Coming on YouTube soon
Search on channel name
" W1VLF "
and
"AM Hi Q box loop"
What the spreaders do
A multi-turn loop only works well when every turn stays evenly spaced and parallel. If the turns bunch up or cross, the inductance shifts and the tuning drifts. Each spreader holds the wire in 18 precision slots, 0.125" wide on 0.250" centers, so every turn sits exactly 1/4" from the next. All exposed edges and slot openings are chamfered so the wire drops in cleanly and doesn’t snag while you wind.
High Q for sharp reception
A tuned multi-turn loop is a high-Q antenna. The loop and its tuning capacitor form a resonant circuit that passes only a narrow slice of the band, the station you’re tuned to, and rejects strong signals nearby. Keeping every turn evenly spaced and parallel keeps the loss low and the Q high, so tuning is sharp and stable.
The loop is also directional, with deep nulls off its sides. Turn it to pull in a weak station, or to null out an interfering station or a local noise source. The combination of narrow tuning and deep nulls makes a loop like this so effective for AM DXing.
Clamp design
Each spreader clamps onto the outside of the PVC arm with a two-piece split clamp:
- The back half is molded solidly into the spreader bar for strength.
- The front half bolts on with two stainless 6-32 screws into captive hex nuts.
- The bore fits standard 3/4" Schedule 40 PVC (1.050" OD), and the clamp grips 1.5" of the pipe.
- The halves leave a small gap, so they squeeze the pipe tight before they touch.
- The clamp flanges run along the bar, so nothing sticks out where the wire leaves the slots.
Two styles
- Standard: a plain spreader bar.
- With feet: a 3/4" foot on each end of the bar, with a rounded contact edge. It gives extra ground clearance and a stable rest when the loop is set down.
Connector mount (choose 1)
A clamp-on connector bracket for the same 3/4" PVC, to mount your feed connector on the frame:
- BNC (single D-hole), or
- SO-239 (4-hole flange)
What’s included
- [4] spreaders: [2 standard + 2 with feet / your chosen style]
- Clamp halves with stainless 6-32 screws and hex nuts, assembled
- 1 connector mount, BNC or SO-239 (buyer’s choice)
What you supply
- 4 × 3/4" Schedule 40 PVC pipe, 12" long
- 1 × 3/4" PVC cross (4-way) fitting
- About 130 feet of #22 to #20 insulated wire (magnet wire or hookup wire)
- A tuning capacitor (40–365 pF variable recommended)
Electrical guide (estimates)
With 12" arms, the loop is about an 18" square. About 17 turns gives roughly 240 µH. With a 40–365 pF variable capacitor, that tunes from about 530 kHz to 1.4–1.5 MHz. To reach the top of the band (1700 kHz), wind about 15 turns, or tap at turn 15. These figures are calculated estimates; your results depend on wire, spacing and wiring stray capacitance.
Specifications
- Slots: 18, 0.125" wide, 0.250" pitch, 0.136" deep
- Spreader bar: 4.625" long × 0.817" wide (4.875" with feet)
- Clamp: 1.5" long, fits 1.050" OD (3/4" Sch 40) PVC
- Hardware: 6-32 stainless screws with hex nuts
- Material: PLA, white
- All parts designed and test-fitted by W1VLF; one-page dimension drawings available on request
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.