This item is pre-owned – it will work like newonce programmed to your vehicle
One (1)
Aftermarket remote keyless entry fob alarm
Transmitter control clicker keyfob controllerreplacement
Functions at 100% Tested & Guaranteed
Audiovox / Prestige/ Pursuit / Pro
FCC ID: ELVAT1C
Interchangeable FCC IDs:
ELVAT1C
ELVATOA
ELVATIC
ELVAT0A
Part #: APS99BT3BCF4
circuit board # ATAE (green LED, not red)
Frequency: 434 – 436 MHz
LED color: Green
3 buttons
Battery: (1) 23A
Compatible with the following systems:
Works on these Audiovox / Prestige / Pursuit systems: APS155CH, APS15CH, APS255C, APS255CH, APS25CH, APS25HT, APS410A, APS511C, APS610C, PRO9246CH, PRO9642CH, PRO9642CHWOS, PRO9644A and PRO9649A.
APS155CH
APS255C
APS255CH
Programming Instructions:
PROGRAMMING TRANSMITTERS:
It is important to remember that during programming, each individual step of the procedure must be executed within 15 seconds of the previous step. When the 15 second time limit is allowed to expire, the system will automatically exit program mode. This is indicated by a long \"chirp\" from the siren.
Additionally, any time the ignition key is turned off while programming, the system will immediately exit program mode. This is also indicated by a long \"chirp\" from the siren.
TO PROGRAM ADDITIONAL TRANSMITTERS:
Note: The programming information described below assumes that the default transmitter is being used and the Lock/Unlock button is one and the same. If you have the optional transmitter with a separate Lock and Unlock button, use letter \"B\" reference below for programming.
Also, where indicated that the siren will emit a long chirp tone, the optional horn may be connected, in which case either or both the horn and siren may sound.
(b) Enter the vehicle, and turn the ignition key to the \"on\" position.
(b) Press and release the valet/bypass push button switch 3 times.
(b) The dash LED will flash one time, and the siren will \"chirp\" 1 time indicating the system is ready to accept programming for channel 1, Arm/Lock and Panic.
The chirp tone confirms that programming of channel 1 was successful.
Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard, or press and release the valet push-button switch two times to advance to step #8.
(b) You can assign the Lock/Arm button by pressing and holding the lock button until the siren emits a long chirp tone.
The chirp tone confirms that programming of channel 1 was successful.
Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard, or move to step #5
(b) The dash mounted LED will flash 2 times, and the siren will \"chirp\" 2 times indicating that the system is ready to accept programming for channel 2. Unlock/2nd Unlock, Disarm, and Panic. Press and hold the Unlock button on your keychain transmitter until the siren emits a long chirp tone. This confirms that programming of channel 2 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard, or
(b) Press and hold the Opt. button on your keychain transmitter until the siren emits a long chirp tone. This confirms that programming of channel 3 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard.
(b) Press and hold any combination of two buttons simultaneously, until the siren emits a long chirp tone. This confirms that programming of channel 4 was successful. Up to 4 transmitters can be programmed, press and hold the selected button of each additional transmitter until the chirp tone is heard, or press and release the push button switch to exit the programming mode, or turn the ignition switch off to exit the programming mode.
The siren emits a long followed by a short chirp tone indicating that the program mode has been exited.
NOTE: If programming to a Keyless Entry (non alarm) unit, there will be NO chirp indication.
QUICK REFERENCE
You can program any individual channel, without reprogramming all channels, by following the quick reference chart below. (Not All Units Have 4 Channels)
CHANNEL
VALET SWITCH
LED
1
Press and Release 3 Times
1 Flash
2
Press and Release 4 Times
2 Flashes
3
Press and Release 5 Times
3 Flashes
4
Press and Release 6 Times
4 Flashes
After the desired channel is programmed, turn the ignition key to the off position to exit programming mode.
Weensure proper working condition of all previously used or new remotes through aserious of tests performed with the Santronics Testing device. Each button istested for functionality prior to shipment and then logged.
Yes. It will have a working battery installed.
Battery Condition:
Your vehicle will be installedwith one of the following keyless entry systems:
The above information can changewhich remote you need
for your installed remote keyless system.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.