Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

2Pcs PCA9685 16Channel 12Bit PWM Servo Driver I2C Module for Raspberry Pi

2Pcs PCA9685 16Channel 12Bit PWM Servo Driver I2C Module for Raspberry Pi
$14.62

Buy Now

2Pcs PCA9685 16 Channel 12-bit PWM Servo Motor Driver Board I2C interface Controller PCA9685 module Raspberry Pi Shield Module Servo Shield
✓Free 30 Day Returns
✓Free Shipping
  • PCA9685 IIC module 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs, which is good when you want to control white or blue LEDs with a 3.4V+ forward voltage
  • PCA9685 module 2-bit resolution for each output - for servos, that means about 4us resolution at an update rate of 60Hz.
  • 3 pin connectors in 4 groups, so you can plug in 16 servos at one time (Servo plugs are slightly wider than 0.1\" so you can only stack 4 adjacent ones on 0.1\"-hole female headers.
  • 16 channel PWM module supports using only two pins to control 16 free-running PWM outputs , the 6 address selection pin allows you to hook 62 driver boards on a single I2C bus, with a total of 992 PWM outputs.
  • This is a PCA9685 16 channel I2C communication, built-in PWM driver and a clock.

Instructions for use:


Drive board connected to board:


The PWM driver board uses the I2C method, so only four lines can be connected to the board: device:
\"Classic\" board: pin mode:
+5V -> VCC
GND -> GND
Analog 4 -> SDA
Analog 5 -> SCL

R3 and later board: pin method
(These boards have dedicated SDA and SCL pins)
+5V -> VCC
GND -> GND
SDA -> SDA
SCL -> SCL
VCC pin is only for the chip power supply, if you want to connect the servo or LED lights, use the V + pin power supply, V + pin supports 3.3 ~ 6V power supply (chip safe voltage 5V).
It is recommended to connect the external power supply via the power supply terminal.

power supply part:


Most of the servo design voltage is 5 ~ 6V, especially in a number of steering gear at the same time running, with the need for high-power power supply. If you are directly using the board: 5V pin to power the servo directly, there are some unpredictable problems, so we recommend that you have a suitable external power supply for the drive board.

Connect the servo:


Most servos are connected using standard 3-wire female plugs, as long as the corresponding pin into the driver board on it. (Ground wire is generally black or brown, the signal line is generally yellow or white)

for the driver board assigned address:


Each drive board of the cascade needs to have a unique access address. The initial I2C address of each driver board is 0 × 40, you can modify the upper right corner of the jumper I2C address. Connect a jumper with solder to indicate a binary number \"1\".

Package include:
2 x PCA9685 IIC module


Shipping
  • We offer FREE shipping on all orders!
  • Under normal circumstances, we try to ship all orders within three business days of payment, normally sooner.
  • We use a selection of shipping services such as TBA, UPS, FedEx, USPS, etc
  • We only ship to the lower 48 states, we do not ship to Alaska/Hawaii, US Protectorates, Puerto Rico, and PO Boxes.
  • Local pickups and combined shipping options are not available at this time.


Returns
  • Although we strive for 100% order fulfillment accuracy, mistakes happen. Please allow us the opportunity to correct any error before leaving us negative response.
  • We are confident in our products, but if you are not fully satisfied with your order, don\'t hesitate to get in touch with us within 30 days of purchase, and we will send you a return label. Once the item is returned we will issue you a full refund.
  • The product must be returned in the original item\'s box, and in the same condition as you received it.


Payment



We accept payment only on Payments(We accept all kinds of credit cards)

Please pay as soon as possible after winning an sale,this will allow us toship your item sooner!





response


Customer satisfaction is our number one priority.
If you have any problems with your order, don\'t hesitate to get in touch with us and we will do our best to meet your needs.




Contact Us

If you have any questions, please don\'t hesitate to contact us. Please allow us 24 hoursto respond, although normally we respond sooner.



Please visit our store to check out other items for sale!

Thank you for shopping at our store.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Popular Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design