2Pcs Motorcycle Projection Light Kit Devil Wings ,Motor LED Light Shadow Lights

Features:

• Universal Motorcycle Welcome Light: This motorcycle projector light is suitable for 95% of motorcycles or electric scooters, etc., and the projection effect appears on both sides of your beloved motorcycle. For example, the glowing wings are compatible with motorcycles

• Easy to install: This motorcycle devil lights is suitable for installation on the motorcycle chassis. The package comes with an adhesive backing, which can be pasted or punched for installation, suitable for installation on the motorcycle chassis. (Note: - - Please confirm whether there is a place for installation before purchase)

• Devil Wing Motorcycle Projector Light: After installing the fixed bracket, it is connected with the vehicle headlight, and there is no need to replace the battery, which is convenient and worry-free.

• Waterproof:The devil light for motorcycles Made of high-quality ABS plastic and aluminum alloy, the sturdy design can withstand various. The waterproof rating ensures that the light can work reliably in any weather conditions.

• High-definition Devil Wing Projector Light: This angel wing lights motorcycle uses high-definition 3D lamp beads, and the projection pattern is clear and bright, with strong light transmittance. This not only makes your vehicle cooler, but also adds a unique personality, making your motorcycle the focus on the road, making you cooler and more eye-catching when driving.

1. Before You Start — Safety Notes

·The lamp — works on 12V only. E-bike battery packs are usually 48V / 60V / 72V — connecting the lamp directly to the main battery will instantly burn out the LEDs.

·Disconnect power and remove the key before touching any wiring.

·Connect only to the headlight circuit or the 12V output of a DC converter — never to the main battery pack.

·Decorative lighting is not street-legal in some regions. Check your local regulations before riding on public roads.

2. Installation Steps

Step 1 — Peel the adhesive backing: Clean and dry the mounting surface (wipe with alcohol for best adhesion), then peel off the protective film from the lamp base.

Step 2 — Mount the first lamp: Stick the lamp on one side of the front section, about 20–40 cm below the headlight. Press firmly for 10 seconds.

Step 3 — Aim the projection angle: Tilt the lamp head downward about 30–45° so the wing pattern lands clearly on the ground beside the bike, not into traffic.

Step 4 — Mount the second lamp: Install the other lamp at the same height on the opposite side. Stand back and confirm the two wings form one symmetrical pair.

Step 5 — Connect the two lamps in parallel: Join positive wire to positive and negative to negative (red = +, black = −). Solder or use the supplied connectors, then insulate each joint.

Step 6 — Test on a 12V power source: Briefly touch the wires to a 12V battery to confirm both lamps light up evenly before permanent wiring. Keep the test short and never let bare wires touch each other.

Step 7 — Open the front panel: Remove the headlight cover or front fairing to reach the wiring. If there is no cable opening, drill a 3–5 mm hole as a passage and smooth its edges.

Step 8 — Locate the headlight positive wire: Use a multimeter: the wire showing 12V when the headlight is on is the positive wire; identify the ground wire as well.

Step 9 — Tap into the headlight circuit: Splice the lamp wires into the headlight positive and ground wires. Solder or crimp, then wrap every joint firmly with insulating tape until no copper is exposed.

Step 10 — Route, refit and final check: Secure the cables with zip ties, keeping them clear of the steering, suspension and hot parts. Refit the panel, start the vehicle and switch on the headlight. Turn the handlebar fully left and right — the wiring must never pull tight.

3. Troubleshooting

·One wing stays dark: — Check its connector first. Most faults are a loose, reversed or corroded joint — not a dead LED. Re-seat the connector and test again.

·Neither lamp lights up: — The wires are reversed. Swap the two connections — no damage is done by reversed wiring.

·Wings overlap or point the wrong way: — Adjust the lamp head angle. Wings look best when they sit side by side without overlapping.

·Lamp falls off after a while: — The mounting surface was not clean. Re-clean with alcohol, dry, and re-apply with firm pressure.

4. Care & Maintenance

The lamps are weather-resistant and designed for outdoor riding. After washing the vehicle or riding in heavy rain, check that the adhesive pads and wire joints are still secure. If the projection dims over time, clean the lamp lens with a soft cloth.

5. FAQ

Q: Will it drain my battery?

A: Power draw is very low (about 1–2 W per lamp). Connected to the headlight circuit, it only works when the lights are on.

Q: Will it fit my bike?

A: It fits any vehicle with a 12V system and a flat mounting area on the front section — motorcycles, scooters and most e-bikes. It is NOT suitable for direct connection to 48V/60V/72V battery packs without a 12V converter.

Q: Does it come on by itself?