BANFLUXION®110V RCA Paper Tape Abrasion Precision Tester Coating Wear Testing Machine 60HzThis RCA Paper Tape Abrasion Tester is a precision instrument designed for evaluating the abrasion resistance of surface coatings on electroplated, painted, screen-printed, and anodized products. Compliant with ASTM F2357-04 standard, it determines coating durability by rolling unlubricated RCA paper tape against the specimen under a fixed load and counting the number of cycles until substrate exposure.
The machine applies a standardized abrasive action using a constant-speed motor running at 17 RPM, producing 157mm of travel per cycle. Three interchangeable load weights (55g, 175g, and 275g) allow testing across a wide range of coating hardnesses and substrate materials. The rotary counter accurately records cycle counts, enabling precise and repeatable test results for quality control laboratories and manufacturing facilities.
Built with a robust stainless steel body, precision-machined aluminum alloy components, and a spring-loaded vertical axis assembly, this tester is engineered for years of reliable service in demanding industrial environments. It is widely used in the electronics, automotive, appliance, and metal finishing industries for evaluating the wear resistance of mobile phone housings, automotive trim, printed labels, and decorative coatings.
Product Name:RCA Paper Tape Abrasion TesterPower Supply:AC 110V / 60Hz / Single-PhaseStandard Compliance:ASTM F2357-04Test Method:Rolling Unlubricated Paper Tape Against SpecimenAvailable Loads:55g / 175g / 275g (Interchangeable)Counter Type:Rotary CounterMachine Speed:17 RPMTravel Rate:1 Cycle = 157mm; 1 Minute = 2670mmOperation Mode:ContinuousBody Material:Stainless Steel & Aluminum AlloyMachine Dimensions:76 x 26.5 x 30cm (29.9\" x 10.4\" x 11.8\")Net Weight / Gross Weight:14.8KG (32.6LB) / 16.9KG (37.3LB)Package Dimensions:83 x 36 x 39cm (32.7\" x 14.2\" x 15.4\")
Spring-Loaded Vertical Axis with Fine Adjustment
The precision vertical axis features a spring-loaded mechanism with a knurled brass fine-adjustment knob, allowing operators to set the exact contact pressure between the O-ring and the specimen. The stainless steel guide rod ensures smooth vertical travel, while the locking collar secures the adjusted position throughout the test. This design guarantees consistent load application and repeatable test conditions across multiple samples.
Dual-Roller Tape Guidance System
Two precision-machined white nylon rollers guide the RCA paper tape smoothly from the supply reel to the take-up reel, maintaining consistent tape tension and alignment during operation. The rollers are mounted in a rigid aluminum alloy frame with adjustable brass-positioned bearings, ensuring the tape travels exactly along the centerline of the instrument. This system prevents tape wander, bunching, or slippage that could compromise test accuracy.
O-Ring Contact Head for Consistent Abrasion
The replaceable O-ring mounted on the vertical axis tip serves as the contact interface between the abrasive tape and the specimen, providing a uniform contact patch that conforms slightly to surface irregularities. Five spare O-rings are included, and replacement is recommended when the outer edge shows wear or cracking, or after six months of regular use. The O-ring can be quickly removed when not in use to prolong its service life.
Precision Brass Micro-Adjustment Mechanism
The swing arm assembly incorporates a precision brass micro-adjustment screw with a knurled locking knob, enabling fine-tuning of the vertical axis angle and contact geometry. This factory-calibrated setting is optimized for the standard 175g load and should not be altered to maintain compliance with ASTM F2357-04. The robust metal construction eliminates backlash and maintains calibration over thousands of test cycles.
Aluminum with anodized coating
The main body and base plate are fabricated from aluminum with anodized coating, providing exceptional rigidity, corrosion resistance, and dimensional stability. All structural joints are precision-machined and secured with high-strength fasteners to eliminate flex or vibration during operation. The durable construction ensures consistent test results and long service life even in high-throughput quality control environments.
Enclosed Motor with Protective Housing
The drive motor is fully enclosed in a stainless steel protective housing that shields it from dust, abrasive debris, and accidental contact. The enclosure features precision ventilation slots for effective heat dissipation during continuous operation. The motor drives the cam and roller system through a sealed bearing transmission, delivering smooth, vibration-free motion at the precise 17 RPM test speed for consistent and reliable abrasion testing.
[ASTM F2357-04 Compliant]: Meets international standard for RCA tape abrasion testing of surface coatings.
[Three Load Weights]: 55g, 175g, and 275g interchangeable weights for testing various coating types.
[Rotary Counter]: Mechanical counter accurately records test cycles for precise result documentation.
[17 RPM Constant Speed]: Maintains consistent 2670mm/min tape travel rate for repeatable results.
[Spring-Loaded Axis]: Ensures uniform contact pressure and compensates for minor surface irregularities.
[Stainless Steel Body]: Corrosion-resistant construction for laboratory and industrial environments.
[110V US Power]: Ready for North American operation with standard AC 110V/60Hz supply.
Operation Method
1. Machine Setup & Leveling:
Place the tester on a flat, stable work surface. Install the four adjustable leveling feet (Q) and use the included ring level to ensure the base is perfectly horizontal. Proper leveling is essential for accurate load application.
2. Vertical Axis Parallel Adjustment:
a. Start the motor and stop it when the cam is at its lowest position (swing arm fully lowered).
b. Insert the slide bolt (C) under the swing arm (E).
c. Loosen the two set screws on the vertical axis (G), then move the axis up or down until the O-ring just contacts the slide bolt surface.
d. Turn the fine adjustment screw (F) until the slide bolt can be moved slightly with corresponding slight movement of the vertical axis.
e. Retighten the set screws to lock the vertical axis position.
f. Remove the slide bolt before starting any test.
3. Sample Mounting:
a. For flat samples: Secure the specimen to the sample stage (P) using the provided binder clips or double-sided adhesive tape.
b. For curved or non-flat samples: Use the universal roller plate specimen holder (A) or the vise-type fixture (B) as appropriate.
c. Adjust the sample position so the test area is centered under the O-ring contact point.
4. Tape Installation:
a. Start the motor and feed the RCA paper tape from the supply reel, passing it upward through the gap between the two guide rollers.
b. Stop the motor and route the tape following the numbered path markers (#1 through #6).
c. Push the pressure roller (W) to the right, pull the tape end to the left, and center it on the winding reel hub.
d. Insert the tape end into the hub notch, release the pressure roller, and rotate the winding reel counterclockwise to wind 2-3 turns.
e. Ensure both winding reel set screws are tightened so the reel rotates with the shaft.
5. Load Weight Selection:
a. For standard testing (175g): Use the tester as-is with no additional weights.
b. For light coatings (55g): Attach the smaller weight to the left-side lever on the swing arm.
c. For heavy-duty coatings (275g): Attach the larger weight to the left-side lever.
d. Do not loosen screw (M) to adjust the swing arm angle. The factory setting is calibrated for 175g testing.
6. Performing the Test:
a. Set the rotary counter to zero.
b. Start the motor. The swing arm will oscillate, driving the O-ring and abrasive tape across the specimen surface.
c. Stop the motor at regular intervals to inspect the test area for substrate exposure (visible color change).
d. Record the cycle count when the substrate first becomes visible. This is the abrasion resistance value for the coating.
e. For continuous high-revolution testing, refer to the manual for converting the counter to free-running mode.
7. Post-Test:
a. Stop the motor and raise the swing arm.
b. Remove the sample and inspect the wear pattern.
c. Clean the O-ring contact surface and remove the O-ring from its mount to prolong service life.
d. Replace the O-ring if wear or cracking is observed on the outer edge.
Safety Precautions
WARNING: Read all instructions before use. Improper operation may result in injury or inaccurate test results.
1. Do Not Adjust Swing Arm Angle: The vertical axis angle is factory-calibrated for 175g load testing per ASTM F2357-04. Do NOT loosen screw (M) on the swing arm clamp. Any angle change will cause irregular loading and invalidate test results.
2. Remove Slide Bolt Before Testing: The slide bolt (C) is for setup calibration only. It must be removed from under the swing arm before starting the motor, or severe damage to the mechanism will occur.
3. O-Ring Maintenance: Replace the O-ring when visible wear, cracking, or deformation appears on the outer edge, or after six months of regular use. Remove the O-ring from the mount when the machine is not in use to extend its life.
4. Proper Grounding: Connect the tester to a properly grounded AC 110V outlet. Do not use adapters or extension cords that defeat the grounding pin.
5. Keep Hands Clear: Keep fingers and loose clothing away from the swing arm, cam, and moving parts during operation. Stop the motor before making any adjustments.
6. Tape Path Verification: Ensure the paper tape is correctly routed through all guide rollers and properly centered on the winding reel before starting. Misaligned tape can jam the mechanism.
7. Sample Securing: Always secure the test specimen firmly to the sample stage before testing. A loose sample can be ejected by the oscillating arm.
8. Motor Housing: Do not remove the motor protective housing during operation. The enclosure prevents contact with hot and rotating parts.
9. Weight Attachment: When attaching 55g or 275g weights, ensure they are fully seated and secured on the lever. A loose weight can fall during operation.
10. Cleanliness: Keep the machine clean and free of abrasive dust. Clean the base and sample stage after each test session. Do not use compressed air to blow dust out of the motor housing.
11. Unplug for Maintenance: Disconnect the power cord before performing any maintenance, cleaning, or mechanical adjustment.
12. Qualified Operators: This equipment should be operated only by trained personnel familiar with ASTM F2357-04 testing procedures.
Item Included (053007)
RCA Abrasion Tester Main Unit *1
LED Magnifier *1
Weight Set (55g + 175g+275) *1
Hex Wrench Set *1
O-Rings *5
Binder Clips *2
Aluminum Sample Plate *1
Power Cord (AC 110V) *1
You can make order with no worry.
Any concern just feel free to let us know, we\'ll reply in 24 hours in normal condition.
Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays.
Warranty: 6 months\' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.
Shipping & Handling Details
Default Shipping Cost or Free Shipping Information:
▲Default shipping cost or free shipping service is only for the customers from Canada or the lower 48 United States by Canada Post, USPS or the UPS Ground. Customers from other areas or needs other shipping ways, please contact us.
▲Buyers from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska, Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there WILL be extra shipping costs, please contact us for more detailed information.
▲Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer.
Handling Time:Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays.
Sales tax / Customs duties:Any sales taxes or Customs duties are not included. If came out, they must be undertaken by the buyer.
Damage In Shipping:Email or call us First! We will work with you to get the case resolved in the fastest method.
Return / Refund
If you are not 100% happy with your purchase, please contact Us. Please don\'t directly opened a request or case without informing us, or else, we will do some discounts on the warranty and other sales-services later on. Hope for your understanding.
Returns & Exchanges
▲All returns must be made within 14 days of delivery date. Items must be in new, unused condition, with all original materials included with the shipment. A partial refund may be applied for opened or damaged items, depending on the condition.
▲Items returned under the buyer’s remorse: The return shipping fee must be covered by the buyer; The original shipping cost will also be deducted from the refund. 15% restocking fee of the items purchase price will be charged.
▲Returns that are the result of our seller\'s error: Buyer will receive a full refund of the item as well as shipping charges
▲All returns require a RA (Return Authorization) number that will be given by our seller. Please contact with us at first for more details.
Defective & Damaged Products
▲If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it\'s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. Hope for your understanding.
▲Replacement or refund of defective or damaged products can only be returned in exchange for the exact same product, or else, the purchase price will be refunded back to your original payment method.
▲If an item is received damaged, customer service must be contacted within 7 days of receiving your item. All returns require a RA (Return Authorization) number as above.
Warranty & response▲6 months\' warranty for the machines, not for the consumables. We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.
▲Any warranty shipping cost to us is responsible by buyer.
▲Any shipping cost to buyer is responsible by the seller.
▲We committee to the customer satisfaction and want to bring you the best purchase experience. If there is any problems, please contact us ASAP. If not, please leave us a positive response as it\'s very important for us. Thanks very much.On Jul 21, 2026 at 00:27:02 PDT, seller added the following information:
On Jul 22, 2026 at 04:36:08 PDT, seller added the following information:
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.