110V Automatic Round Bottle Labeling Machine with Touch Screen Label Applicator

EFFLUVIALTECH® – 110V Automatic Round Bottle Labeling Machine EFFLUVIALTECH® 110V Automatic Round Bottle Labeling Machine Product Overview The round bottle labeling machine uses roll-fed self-adhesive label paper and applies the labels using a rolling mechanism. This self-adhesive labeling machine offers clean and hygienic operation without mold growth. After labeling, the products look neat, the labels adhere firmly and will not peel off, and the production efficiency is high.Product Parameters Power Supply 110V, 1 kW, 60Hz Output Speed 20–200 PCS/min (Depends on bottle size and label length) Applicable Bottle Diameter 20–120 mm (0.79\"–4.72\") Label Height 15–150 mm (0.59\"–5.91\") Label Length 25–300 mm (0.98\"–11.81\") Labeling Precision ±1 mm (excluding label tolerance) / ±0.04\" Label Roll Inner Diameter 76 mm (2.99\") Label Roll Outer Diameter 250 mm (9.84\") Body Material High-Quality Stainless Steel Precautions ⚠ Note: For best performance and stable speed, we suggest the label length covers 1/2 of bottle circumference; coverage up to 2/3 is acceptable. Full-wrap labels may affect labeling quality; for this application, our fixed-point labelling machine is recommended.

• This machine operates on 110V voltage. The interval between powering on and off must be greater than 30 seconds to prevent damage to electrical components.
• The parameters of the servo driver, inverter, and PLC inside the chassis must not be changed at will; otherwise, the machine may not operate normally.
• Do not bend or kink the optical fiber during operation, as this may cause labeling errors. If the fiber needs to be replaced, ensure the specifications are identical.
• Before starting the labeling process, ensure that the \"Emergency Stop\" button below the touch screen is in the popped-up (released) state; otherwise, the machine cannot start.
• Avoid scratching the touch screen surface to prevent poor touch response.
• The main rubber wheel should be cleaned with alcohol. If labels stick to the surface, never use sharp tools to scrape them off to avoid damage.
• Keep the conveyor belt surface clean. If dirt is difficult to wipe off, use a brush to remove it.
• Check the drive belt of the main labeling motor once a month. If it is too loose, adjust it appropriately, but do not over-tighten it to avoid mechanical resonance noise.
• The machine chain generally requires lubrication maintenance after about 3 months of use to prevent gear friction from damaging the machine.
• Do not arbitrarily change the wiring, data cables, or pneumatic interfaces. Bearings in all parts should also be checked regularly to prevent screws from loosening.

Product Details and Advantages Control Panel Touch control panel with a clean and clear interface. Parameter modifications are intuitive and easy to understand, and switching between various functions is simple. Operators can quickly complete debugging and efficiently carry out labeling tasks. High-Power High-Speed Motor Delivers strong power for stable and smooth operation, supporting long-term continuous work with minimal risk of failure to ensure uninterrupted labeling. Full Stainless Steel Body Constructed entirely from stainless steel for a sturdy, impact-resistant structure. Corrosion-resistant surface is easy to clean, making it suitable for various production environments such as food and daily chemicals. Adjustable Label Supply Reel The supply reel supports rotational adjustment, with tension easily set via screws. It accommodates label rolls of various specifications, making reel changes and debugging quick and effortless. High-Quality Optical Sensor Equipped with a high-quality detection sensor for precise and sensitive recognition. Ensures minimal labeling errors and high stability, effectively guaranteeing neat and uniform label positioning while reducing defects. Label Guide & Stabilizer Guides and stabilizes the label web to avoid deviation during feeding. Maintains consistent tension for precise label detection and accurate labeling position. Operating Instructions 1. Loading the Label (Threading Steps)

1. Confirm the correct front and back orientation of the labels.
2. Move the bottom guide ring to the appropriate position. Thread the labels along the routing path shown in the machine diagram and pull them smooth.
3. Secure the end of the label onto the rewinding reel, and push the upper guide ring flush with the label edge.
4. Lock the pressure rollers for label dispensing and rewinding. Press the \"Label Length\" key to let the computer automatically calculate the length and gap (ensure the calculated value matches the actual length).
5. Calibrate the dispensing position and length by adjusting the position of the label detection sensor (fiber optic).

2. Machine Adjustment

1. Label Head Adjustment: Use the label head lifting handwheel to adjust the height of the label head plate to match bottles of different heights.
2. Wheel Attachment Mechanism Adjustment: The ideal state between the workpiece and the wheel attachment is a slight clamping. Rotating the handwheel clockwise moves the pressure plate forward; counterclockwise moves it backward. If it is too loose or too tight, correct it by adjusting the screws.
3. Optical Sensor Sensitivity Adjustment: Adjust the coarse and fine tuning knobs on the fiber amplifier so that the indicator light shows the correct status when the sensor detects a label.

3. Touchscreen Operation

1. Simultaneous Start: The \"Conveyor Start\" and \"Labeling Start\" buttons must be turned on simultaneously for the machine to begin working.
2. Manual Dispensing: Jog the button to dispense a single label (used for testing).
3. Dispensing Length / Speed / Delay: Used to control the maximum dispensing length (to prevent waste), dispensing frequency, and the delay time for dispensing after a bottle is detected.
4. Production Setting: Preset the target production quantity; the machine will automatically stop once the count is reached.

Items Included (160044)

• 1 × 110V Automatic Round Bottle Labeling Machine

Shipping & Handling Details

Default Shipping Cost or Free Shipping Information:
▲ Default shipping cost or free shipping service is only for the lower 48 United States by UPS Ground or USPS. Other areas or needs other shipping ways, please contact us.
▲ Buyers from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska, Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there WILL be extra shipping costs, please contact us for more detailed information.
▲ Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer.

Handling Time: Shipping is usually made in 1–3 business days after payments cleared. Orders are processed from Monday–Friday; Not on the weekends & public holidays.

Sales Tax / Customs Duties: Any sales taxes or Customs duties are not included. If came out, they must be undertaken by the buyer.

Damage In Shipping: Email or call us First! We will work with you to get the case resolved in the fastest method.

Return / Refund

If you are not 100% happy with your purchase, please contact Us. Please don\'t directly opened a request or case without informing us, or else, we will do some discounts on the warranty and other sales-services later on. Hope for your understanding.

Returns & Exchanges
▲ All returns must be made within 30 days of delivery date. Items must be in new, unused condition, with all original materials included with the shipment. A partial refund may be applied for opened or damaged items, depending on the condition.
▲ Items returned under the buyer’s remorse: The return shipping fee must be covered by the buyer; The original shipping cost will also be deducted from the refund. 15% restocking fee of the items purchase price will be charged.
▲ Returns that are the result of our seller\'s error: Buyer will receive a full refund of the item as well as shipping charges.
▲ All returns require a RA (Return Authorization) number that will be given by our seller. Please contact with us at first for more details.

Defective & Damaged Products
▲ If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it\'s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. Hope for your understanding.
▲ Replacement or refund of defective or damaged products can only be returned in exchange for the exact same product, or else, the purchase price will be refunded back to your original payment method.
▲ If an item is received damaged, customer service must be contacted within 7 days of receiving your item. All returns require a RA (Return Authorization) number as above.

Warranty & response

▲ 6 months\' warranty for the machines, not for the consumables. We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.
▲ Any warranty shipping cost to us is responsible by buyer.
▲ Any shipping cost to buyer is responsible by the seller.
▲ We committee to the customer satisfaction and want to bring you the best purchase experience. If there is any problems, please contact us ASAP. If not, please leave us a positive response as it\'s very important for us. Thanks very much.

On Nov 13, 2026 at 00:01:26 PST, seller added the following information: