Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

ScanLab Scanner IntelliscanIII 20 / 1080nM Won’t Move In X See Pics

ScanLab Scanner  IntelliscanIII  20 / 1080nM Won’t Move In X See Pics
$499.00

Buy Now

The ScanLab intelliSCAN III 20 (1080nm / $20\\text$ aperture) is a digital, high-precision galvanometric scan head. When an axis (X-axis) completely stops responding, the issue typically stems from a power delivery failure, digital bus handshake fault, internal response error, or driver board protection shutdown.

Here is a systematic diagnostic process to identify why the X-axis galvo motor won\'t move:

1. Check Diagnostic LED Status Indicators

Before cycling power, look at the LED indicators on the back panel of the intelliSCAN III unit:

  • POWER / OK LED: Should be solid green.

  • X-Axis Status LED:

    • Off / Red: Indicates a power supply issue, over-temperature fault, or severe galvo fault.

    • Blinking Red/Yellow: Indicates a position error (e.g., galvo mirror hit a mechanical stop, tracking error threshold exceeded, or missing encoder signal).

    • Solid Green: The scanner board thinks it is receiving position commands. If it’s green but not moving, check software gain/scale settings or command wiring.

2. Verify DC Power Voltages

Galvanometer scanners require clean, dual-rail DC power (typically $\\pm15\\text$ to $\\pm24\\text$ depending on configuration, plus $+5\\text$ logic):

  • Measure voltage at the main power connector on the back of the scan head with a multimeter.

  • If either the positive or negative power rail drops out or drops below nominal voltage, the drive amplifier will shut down the affected axis to protect the motor coil.

3. Inspect SL2-100 / XY2-100 Control Bus Wiring

The intelliSCAN III uses the digital SL2-100 protocol (or XY2-100) to receive coordinate data from the RTC control card (e.g., SCANLAB RTC4 / RTC5 / RTC6):

  • Swap Command Channels (Logic Test): Power off the system, then swap the X and Y channel outputs from your RTC card (or swap the command signals if using discrete breakout cables).

    • If the Y-axis stops moving and the X-axis starts moving, the issue is a dead channel on the RTC control card or a corrupted software configuration.

    • If the X-axis still won\'t move, the fault lies inside the scan head assembly (driver, cabling, or galvo motor).

4. Internal Scan Head Isolation (Galvo vs. Drive Board)

Safety Warning: Disconnect the $1080\\text$ laser source before opening the housing. $1080\\text$ (Near-Infrared) laser beams are invisible and pose extreme eye hazards.

If electrical/power inputs are normal, the fault is internal:

  1. Galvo Mirror Obstruction: With power OFF, carefully inspect the X-axis galvo mirror under a clean light. Check if debris, set screws, or a physical mechanical crash jammed the mirror shaft.

  2. Internal Flex Cable Connection: The intelliSCAN III uses internal flex cables connecting the main board to the individual driver cards and optical encoders. Thermal cycling or high vibration can loosen internal ribbon/flex connectors.

  3. Internal Fuse / Driver Protection: Each galvo driver axis on the internal processing board has over-current thermal protection. If the galvo coil overheats or shorts, the drive board latches off until power is fully cycled.

Summary of Most Common CausesSymptomProbable CauseActionNo status LED for X-axisBlown internal fuse or missing DC voltage railCheck system power supply Red status LEDTracking error / Optical encoder faultVerify SL2-100 cable; check for mirror jamY works, X dead (Commands swapped)Faulty RTC control card outputReplace/reconfigure RTC card portY works, X dead (Commands static)Blown X-driver board or burned galvo coilRequires SCANLAB OEM factory repair

The ScanLab Scanner IntelliscanIII 20 is a high-quality scanner made by the renowned brand Scan Lab in Germany. This model offers a resolution of 20/1080nM, providing precise and detailed scanning capabilities. With its advanced technology and reliable performance, this scanner is ideal for various industrial and business applications that require accurate and efficient scanning solutions.


03.26GARAGE4

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design