Pin code standalone access control 1K User EM 125Khz extendable data backupable

Product Description

Features:

1. Data backup.you canbackup all theenrollments data intoa memory IC and then restore to othersame devices.
2. Delete/Add cards by master card,
3. Anti-probe the password
4. AddID cards by the room number,such ascan namecards to the controller as\"201\"(201 is a room number),emember

the cardsbut not its real number so that you don\'t have to remember all thecards\' number especially when a card lost. 5.Capacity can be extended up to 16K if you need.
6. It has 3 modelsthose are compatible with Mifare1/Hid/EM ,please look the tablet below.

Parallel all the models support: open the door by password, by card + password , manage the device by master card,data backup

and restore by memory IC.

Extendable Optional:Remote control,RFID reader

Card Type:

Card use card

2

Daytime using card,invalid during evening

3

Password attached card,must typing in PW after card reading whenever

4

Password attached during evening.Only card reading is valid during daytime

Pin Description and wiring open of relays, capacity point of relays, capacity close of relays, capacity to open switch

7

DOOR

Connect to door magnetic sensor

8

ALM

Alarm bell output port, current load 100mA

9

WG0

Wiegand 26 reader data lines (data 0),when a reader 26 reader data lines (data 1) ,when a reader In

0*password# .Default administrative password:1234

Log off

0*#

The functions below should be operated in a Log in status

Change password

1*newpassword# (password should be 4~6 bits)

Dispatch user PW

2*userpassword#(user password should be 4~6 bits)

Delete user PW

3*user password#

Delete all user PWs

3*9*9#

Dispatch type 1card

4*1# card reading(if more cards,can read card continuously)

Dispatch type 2 card

4*2# card reading(if more cards,can read card continuously)

Dispatch type 3 card

4*3# card reading(if more cards,can read card continuously)

Dispatch type 4 card

4*4# card reading(if more cards,can read card continuously)

Dispatch a remote

4*5# pressing any key of the remote,the device beep once means OK.

Delete cards

5*card number# (card number is a 10 bits printed on card)

Delete all cards

5*9*9# (the device beep once means finished)

Delete a card type

6*card type#

Delete all cards&PW

6*9*9#

Setup to night mode

7*password#

Setup to Normal Open

8*password#(conveniently for going to work every morning)

Setup open delay

9*seconds# (seconds is a 0~99 digit means the duration of delay)

Setup fault PW times

10*fault times#(a 2~9 digit,means fault PW entering times,default is 5)

Setup device suspend time

11*suspend time#(1~99 ,means 1~99 seconds,default is 10)

Restore the Manufacture setup

12*#

Setup stress PW

13*stress PW#(4~6 bit)

The functions below should be operated in a normal status

PW open

PW #

Card open

Card reading,(if a PW needed,press the PW)

On/Off the night mode

7*PW #

On/Off NO status

8*PW #

Modify the user PW

after card reading,press *1* new password# during green light flashing

Turn on the Stressing Alarm

Stress PW#

Turn off the Alarming

Read any authorized user card

Others

1. press ** anywhen will exit
2. if the operation is right,the buzzer will sounda long beep,if wrong operation,3 short beep.
3. Press and hold the reset button for 1 second,one beep,all the setup will be restore to manufacture default.
4. Press and hold the reset button for 3 seconds,not only restore the manufacture default,but also delete all the data including dispatched cards and PW