Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

Photolithography Shutter Control Rackmount Enclosure Relay I/O Astec Corcom

Photolithography Shutter Control Rackmount Enclosure Relay I/O Astec Corcom
$184.00

Buy Now

Photolithography Shutter Control Rackmount Enclosure Relay I/O Astec Corcom

Photolithography Shutter Control Rackmount Enclosure Relay I/O Astec Corcom

This is a custom-built rackmount enclosure designed as a shutter and relay I/O control system, most likely for a photolithography or mask aligner instrument. The front panel carries five labeled status indicators — AC Power, ARC Power, CCD Shutter, Mask Vacuum, and ARC Lamp Shutter — and a main power rocker switch, consistent with control systems used to sequence arc lamp, shutter, and vacuum functions in contact or proximity mask aligners. The enclosure is approximately 4U rackmount size and is constructed in a steel chassis with rack ears. It is being sold AS-IS for parts or repair and has not been tested at our facility.

Specifications & What\'s Included

  • Enclosure: steel rackmount chassis, approximately 4U, with rack ears
  • Internal PSU 1: Astec PS ACV 5N9-1 (5V output)
  • Internal PSU 2: Astec PS ACV 12N5 (12V output)
  • Internal transformer: large toroidal/laminated transformer (yellow-wrapped)
  • EMI Filter: Corcom 10VK7 — 10A, 120/250V, 50-60Hz, UL and CSA listed, Made in Mexico
  • Solid State Relay: Crydom D2425
  • Relay I/O Board: PC 6222 Rev C — labeled STA-U, 9627/D 25249, copyright 1984
  • Front panel indicators (5): AC Power, ARC Power, CCD Shutter, Mask Vacuum, ARC Lamp Shutter
  • Front panel: illuminated rocker power switch
  • Rear panel AC outlet: isolated ground duplex outlet
  • Rear panel AC input: IEC C14 inlet
  • Rear panel fuse: 15 Amp
  • Rear connectors: J5, J6 (XLR-style circular); J7, J8, J9, J10 (large mil-spec circular multi-pin); J4 (gold D-sub connector)
  • Internal wiring: rainbow ribbon cables connecting relay I/O board to terminal blocks and output connectors
  • Condition: AS-IS, for parts or repair — not tested, no functionality type of relay I/O control enclosure was used in photolithography systems — specifically mask aligners and contact printers — to sequence and control arc lamp power, optical shutters, CCD exposure triggers, and vacuum clamping for mask-to-wafer alignment. Mask aligners of this era (mid-1980s through early 1990s) relied on discrete relay-based I/O controllers housed in standalone enclosures to interface the main instrument controller with high-current lamp and solenoid loads, providing electrical isolation between logic-level signals and powered actuators. The isolated ground outlet and mil-spec circular connectors suggest this unit interfaced directly with an aligner\'s lamp housing, shutter solenoids, and vacuum pump. Equipment of this type was common in university microfabrication labs, semiconductor research facilities, and small-volume IC fabrication lines during the 1980s and early 1990s. The individual components — Astec power supplies, Corcom EMI filter, Crydom solid-state relay, and the relay I/O board — retain value as spare or salvage parts for compatible systems or general relay control applications.

    Condition: For Parts or Not Working
    This photolithography shutter and relay I/O control rackmount enclosure is being sold AS-IS for parts or repair. It has not been tested and no functionality is guaranteed. The enclosure houses an Astec 5V power supply (ACV 5N9-1), an Astec 12V power supply (ACV 12N5), a large toroidal transformer, a Corcom 10VK7 EMI filter (10A, 120/250V, 50-60Hz), a Crydom D2425 solid-state relay, and a relay I/O board (PC 6222 Rev C, STA-U 9627/D 25249, copyright 1984). The enclosure and internal components appear intact and free of obvious physical damage based on the photos, but the system has not been powered or verified at our facility. This lot contains a variety of useful components for repair, salvage, or integration into a compatible photolithography or custom control system. Please view our photo set and contact us if you have any questions. Visit Our Store

    Shop industrial, solar, scientific, vintage computing, electronic test, audio-visual, office equipment, and manuals in our store. Start shopping »

    Follow Our store

    Want first pick on new arrivals? Tap Save Seller at the top of any page — alerts you the moment we list something new.

    Fast Shipping

    We ship via most standard carriers. Local pick-up available at our Ventura, CA warehouse.

    About Us

    Questions? Contact us anytime. Learn more about us »

    Best Offers

    Want to make an OFFER but don\'t see a MAKE OFFER button? Use the Contact Seller button at the top of this listing.

    30-Day Guarantee

    100% satisfaction guaranteed. Any issue, just reach out — we\'ll make it right.

    Thank you for shopping with us.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design