|
>> If you dont know how to design a userbar, then write here a Userbar that you want.
>> If you know how to design them help these people and design what they request.
|
 |
 |
USERBARS.org | Free Forum Userbars
| On eBay now |
Modbus Rtu 1/2/4 Channel 7-24V Relay Module Switch input output RS485/TTL UART
$4.95

Keywords you may need:Sensors Tester ESP32 FNIRSI Development Board NodeMCU Multimeter Speed Controller Spot Welder Relay Temperature Controller LCD OLED LED&RGB Adapter Amplifier Power supply Step Up Step down Converter Switch Transmitter Light Singal Generator Dear customer: Thank you for visit our store,we are proffessional \"Business & Industrie\" seller for 10 years,our main products included:Sensors,modules devolpment board, LED displays, other IC procuts an so on,any question about DIY robot,Arduino,or Raspberry Pi will be welcome to discuss with us,we will try our best to supply the most advanced product and price,(if we sale more,the cost of made one product will be reduce and we will change or price to make you save more. Hope you enjoying yourself here! We appreciate your business! We only ship to the confirmed address provided by PayPal. Before you pay, please make sure your address in PayPal matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand. -We ship items to Worldwide. Thank you! -we will ship out the order in 1-2 business days after payment cleared .Since it is international shipping ,delivery time is about 15--28 business days to arrive to most countries. PaymentWe accept PayPal payment ONLY. Refund* We believe our items are so outstanding. We are convinced you will be happy with your Purchase. * If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund to you after the returned item arrived at our warehouse. * Please include your ID and item number with any email requests. response* When you satisfied with our product and services please leave us positive response. * If you have got the package, please confirm \"Delivery on time\" For us. * If a problem occurs, contact us immediately with any email request. * Just contact us using the \" Ask the seller a question\" link on . Modbus Rtu 1/2/4 Channel 7-24V Relay Module Switch input output RS485/TTL UART1 ChannelSingle Modbus relay module is equipped with mature and stable 8-bit MCU and RS485 level communication chip. RS485 communication using standard MODBUS RTU format Communication protocol, which can realize 1 optical coupler input signal detection and 1 relay output, which can be used for digital Word quantity detection or power control occasions. Product parameter 1. Onboard mature and stable 8bit MCU and MAX485 level conversion chip 2. Communication protocol: support standard Modbus RTU protocol 3. Communication interface: support RS485/TTL UART interface 4. Communication baud rate: 4800/9600/19200, default 9600bps, support power-off save 6. Optocoupler input signal range: DC3.3-30V (this input cannot be used for relay control) 7. Output signal: relay switch signal, support manual, flash off, flash off mode, flash off/flash The base number of the time delay is 0.1S, and the maximum flash-off/flash-off time can be set as 0xFFFF*0.1S=65535*0.1S=6553.5S 8. Device address: range 1-255, default 255, support power-off save 9. Onboard 1 way 5V, 10A/250V AC 10A/30V DC relay, can suck continuously 100,000 times, with diode effusion protection, short response time 10. On-board relay switch indicator 11.Supply voltage: DC7-24V, with input anti-reverse connection protectionPackage included:DC 7-24V Relay Module RS485/TTL1 Input And Output With Anti-reverse Protection2 ChannelDescription: Dual ModbSU relay module is equipped with mature and stable 8-bit MCU and RS485 level communication chip. RS485 communication using standard MODBUS RTU format Communication protocol, can realize 2 input signal detection, 2 relay output, can be used for digital In the case of volume detection or power control. Product parameter 1. Onboard mature and stable 8bit MCU and MAX485 level conversion chip 2. Communication protocol: support standard Modbus RTU protocol 3. Communication interface: support RS485/TTL UART interface 4. Communication baud rate: 4800/9600/19200, default 9600bps, support power-off save 6. Optocoupler input signal range: DC3.3-30V (this input cannot be used for relay control) 7. Output signal: relay switch signal, support manual, flash off, flash off mode, flash off/flash The base of the delay time is 0.1S, and the maximum flash-off/flash-off time can be set as 0xFFFF*0.1S-65535*0.1S=6553.5S 8. Device address: range 1-255, default 255, support power-off save 9. Onboard 1 way 5V, 10A/250V AC 10A/30V DC relay, can suck continuously 100,000 times, with diode effusion protection, short response time 10. On-board relay switch indicator 11.Supply voltage: DC7-24V, with input anti-reverse connection protectionPackage Include:1x DC 7-24V Dual Channel Relay Module Switch Input And Output RS485/TTL 4 ChannelModbus RTU four-way relay module RS485/TTL UART 4 inputs 4 outputs I. Overview Elsay four-way Modbus relay module is equipped with mature and stable 8-bit MCU and RS485 level communication chip. Using standard MODBUS RTU format RS485 communication protocol, it can realize 4 input signal detection and 4 relay output, which can be used for digital detection or power control occasions.
II. Features 1. Onboard mature and stable 8bit MCU and MAX485 level conversion chip;
2, Communication protocol: support standard Modbus RTU protocol;
3. Communication interface: support RS485/TTL UART interface;
4. Communication baud rate: 4800/9600/19200, the default is 9600bps, and it supports power-off save;
5. Optocoupler input signal range: DC3.3-30V (this input cannot be used for relay control);
6. Output signal: relay switch signal, support manual, flash off, flash off mode, flash off/flash off delay base is 0.1S, the maximum flash off/flash off time can be set to 0xFFFF*0.1S=6553.5S; 7. Device address: range 1-255, default 255, support power-off save;
8. The baud rate, input signal, relay status, and device address can be read using software/commands; 9. There are 4 5V, 10A/250V AC 10A/30V DC relays on board, which can be activated continuously for 100,000 times, with diode effusion protection, and short response time;
10. On-board relay switch indicator;
11. Power supply voltage: DC7-24V, support DC socket/5.08mm terminal power supply, with input anti-reverse protection;III. Hardware introduction and description1. Board size2. Interface introduction1. DC-005 socket: DC7-24V power input socket; 2. VCC, GND: DC7-24V 5.08mm power input terminal; 3. DC3.3-30V optocoupler signal input: IN1: Channel 1 positive IN2: Channel 2 positive IN3: Channel 3 positive IN4: Channel 4 positive GND_IN: Common terminal negative 4. A+, B-: RS485 communication interface, A+, B- are respectively connected to A+, B- of the external control terminal;
5. Relay switch signal output: NC: Normally closed terminal, the relay is short-connected with COM before it is closed, and it is suspended after it is closed; COM: public end; NO: Normally open end, the relay is suspended before closing, and shorted to COM after closing. 6, GND, RXD, TXD: TTL level UART communication interface, GND, RXD, TXD are respectively connected to GND, TXD, RXD of the external control terminal;IV. Product Parameters: 1>.Item name: 4CH Modbus Relay Module 2>.Work voltage:DC 7V~24V 3>.Baud rate:4800/9600/19600bps(default 9600bps) 4>.Optocoupler input signal:DC 3.3V~30V 5>.Set address:1~255 6>.Relay contorl mode: ON/OFF,Delay_ON,Delay_OFF mode 7>.Delay time: 0~6553.5s 8>.Load: AC 250V 10A or DC 28V 10A 9>.Protocol:Modbus RTU 10>.Interface:RS485/TTL UART 11>.Control channel: 4channel 12>.Operating Temperature:-20℃~85℃ 13>.Operating Humidity:5%~95%RH 14>.Module Size:93*90*20mm V. Modbus RTU Command: 1>.Suppose the device address is 0xFF so return 00 10 00 00 00 01 02 00 FF EB 80 and the 9th btye is device address. 2>.Turn ON CH_1 Relay(Normal Mode): Send: FF 05 00 00 FF 00 99 E4 Return: FF 05 00 00 FF 00 99 E4 Note_1:The 3rd and 4th byte are relay addresses.So it can be 0x0000,0x0001,0x0002,0x0003. Note_2:The 5th and 6th byte are relay data.0xFF00 means turn ON relay and 0x0000 means turn OFF relay. 3>.Turn OFF CH_1 Relay(Normal Mode): Send: FF 05 00 00 00 00 D8 14 Return: FF 05 00 00 00 00 D8 14 4>.Turn ON CH_2 Relay(Normal Mode): Send: FF 05 00 01 FF 00 C8 24 Return: FF 05 00 01 FF 00 C8 24 5>.Turn OFF CH_2 Relay(Normal Mode): Send: FF 05 00 01 00 00 89 D4 Return: FF 05 00 01 00 00 89 D4 6>.Turn ON All relays: Send: FF 0F 00 00 00 08 01 FF 30 1D Return: FF 0F 00 00 00 08 41 D3 7>.Turn OFF All relays: Send: FF 0F 00 00 00 08 01 00 70 5D Return: FF 0F 00 00 00 08 41 D3 8>.Set device address to 0x01: Send: 00 10 00 00 00 01 02 00 01 6A 00 Return: 00 10 00 00 00 01 02 00 01 6A 00 Note: The 9th btye is device address. 9>.Set device address to 0xFF: Send: 00 10 00 00 00 01 02 00 FF EB 80 Return: 00 10 00 00 00 01 02 00 FF EB 80 10>.Read device address: Send: 00 03 00 00 00 01 85 DB Return: 00 03 02 00 FF C5 C4 Note: The 5th btye is device address. 11>.Read relay status: Send: FF 01 00 00 00 08 28 12 Return: FF 01 01 01 A1 A0 Note:The 4th means which one relay.0 means OFF and 1 means ON. 12>.Read optocoupler input staturs: Send: FF 02 00 00 00 08 6C 12 Return: FF 02 01 01 51 A0 Note:The 4th means which one input.0 means low level signal input and 1 means high level signal input. 13>.Set baud rate 4800bps: Send: FF 10 03 E9 00 01 02 00 02 4A 0C Return: FF 10 03 E9 00 01 C5 A7 Note:The 9th btye is baud rate value.0x02 is 4800bps.0x03 is 9600bps.0x04 is 19200bps. 14>.Set baud rate 9600bps: Send: FF 10 03 E9 00 01 02 00 03 8B CC Return: FF 10 03 E9 00 01 C5 A7 15>.Set baud rate 19200bps: Send: FF 10 03 E9 00 01 02 00 04 CA 0E Return: FF 10 03 E9 00 01 C5 A7 16>.Turn ON CH_1 Relay(2S Flashing Mode): Send: FF 10 00 03 00 02 04 00 04 00 14 C5 9F Return: FF 10 00 03 00 02 A4 16 Note_1:The 3rd and 4th byte are relay addresses.So CH1~CH4 can be 0x0003,0x0008,0x000D,0x0012. Note_2:The 10th and 11th byte are delay time in second.The minimum delay time is 0.1s.Relay will OFF after delay time.So the delay time in this command is : 0x0014*0.1=2S. 17>.Turn OFF CH_1 Relay(3S Flashing Mode): Send: FF 10 00 03 00 02 04 00 02 00 1E A5 99 Return: FF 10 00 03 00 02 A4 16 Note:Relay will ON after delay time.So the delay time in this command is : 0x001E*0.1=3S. VI. Package Include: 1PC 4CH Modbus Relay Module Am 13.01.2026 hat der Verkäufer die folgenden Angaben hinzugefügt:

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
|
|
|
 |
 |
|