Automatic Voltage Regulator Control Panel AVR EA05A For Generator Genset

Description:Sensing InpuuutVoltage 220 / 380 / 440 VAC, 1 phase2 wireDIP switch selectableFrequency 50 / 60 Hz, DIP switch selectablePower InputVoltage 100 ~ 300 VAC, 1 phase 2 wireOutputVoltage Max. 90 VDC @ 240 VAC inputCurrent Continuous 5AIntermittent 7A for 10 secResistance Min. 15 ohm Max. 100 ohmVoltage Regulation< ± 0.5% ( with 4% engine governing )Voltage Build-upResidual voltage at AVR terminal > 5 VACThermal Drift0.03% per °C change in AVR ambientExternal Volts Adjustmen± 7% with 1K ohm 1 watt trimmerEMI SuppressionInternal electromagnetic interference filteringUnit Power DissipationMax. 8 wattUnder Frequency Protection (Factory Setting)60 Hz system presets knee point at 55 Hz50 Hz system presets knee point at 45 HzSoft Sta...

Automatic Voltage Regulator Control Panel AVR EA05A For Generator Genset

Description:
Sensing Inpuuut
Voltage 220 / 380 / 440 VAC, 1 phase2 wire
DIP switch selectable
Frequency 50 / 60 Hz, DIP switch selectable
Power Input
Voltage 100 ~ 300 VAC, 1 phase 2 wire
Output
Voltage Max. 90 VDC @ 240 VAC input
Current Continuous 5A
Intermittent 7A for 10 sec
Resistance Min. 15 ohm Max. 100 ohm
Voltage Regulation
< ± 0.5% ( with 4% engine governing )
Voltage Build-up
Residual voltage at AVR terminal > 5 VAC
Thermal Drift
0.03% per °C change in AVR ambient
External Volts Adjustmen
± 7% with 1K ohm 1 watt trimmer
EMI Suppression
Internal electromagnetic interference filtering
Unit Power Dissipation
Max. 8 watt
Under Frequency Protection (Factory Setting)
60 Hz system presets knee point at 55 Hz
50 Hz system presets knee point at 45 Hz
Soft Start Ramp Time
3 sec.
Dimensions
101mm L * 69mm W * 47.5mm H
Weight
183g ± 2%
2. Wiring
When generator supply is over load, N phase will be different with the sharing load by 3 phases (load imbalance). Hence, the voltage from N phase to 3 phases (R.S.T.) will be altered. When the rated voltage of the traditional single input’s AVR is above 220V, it will increase the voltage drift rate by using N phase as the detective input. It will also cause the voltage imbalance.
EA05A can improve the above situation, and increase the generator’s rated voltage usage space,such as 380V, 440V. We can all detect by the “phase voltage”.
1. When the rated phase voltage of the generator is 220VAC, the input terminals B, C and sensing terminals A, C can join together. or connect independent.(as show as figure2).
2. When the rated phase voltage of the generator is 380V, 440V, the input terminals B, C and sensing terminals A, C must separate connect the wiring (as show as Figure 4 or figure 5). The voltage between B and C must not be over 300 VAC.
3. F+ F- terminals connect to the generator field. (J and K) FEXT.VR is the potentiometer (1KΩ 1W). These two terminals must be by-pass when external potentiometer is needless.
P.S. : A, B, C, F+ F- the usage of wire gauge are AWG16 or 1.25 mm2 85。
C above 600V.
The EXT.VR connection wires must be made of isolated wiring.
3. Adjustments
The voltage setting for 220V/380V/440V and the
frequency setting for 50/60HZ is show in figure7.
Please check the voltage/frequency selector setting
is correct before start the generator.

Caution:
The Generator Or Avr May Be Damaged
If The Voltage / Frequency Selector
Setting Is Incorrect.
Ufro Dip:
1. Before you turn on the generator, please turn the
voltage adjustment and stability adjustment full anti-clockwise. After the generator is on and run stably, turn the voltage adjustment clockwise to reach the required out voltage. (If there is an external potentiometer, turn the external potentiometer to the middle position before adjust internal voltage potentiometer.)
2. Adjust “Stability Adjustment” clockwise slowly to
change the response time between AVR and the generator. If the adjustment is too big, it might cause the voltage instable. If too small, the load voltage will change too much at heavy load. Our suggestion is to trace by the multi-meter DCV. To adjust “stability adjustment”, you
just need to make the multi-meter waving smaller. It can also improve the full load’s voltage drift rate.
4. Field Flashing
When the regulator is operated with the generator for
the first time, the polarity of residual magnetism may be reversed or too small to achieve the necessary build-up voltage for the regulator. If reversing the field connections does not induce build-up, and the residual voltage is less than the specified value of 5 Vac, shut down the Prime-mover and proceed with the following steps :
1. With the Prime-mover at rest and the regulator’s
field output wires disconnected, apply a DC source ( NOT grounded ) of not more than 3~12 Vdc with Positive to F+ and Negative to F-, in series with a current-limiting resistor of 3~5 ohms 20 watt. (The set battery is a suitable source.)
2. Allow approximately 3 seconds before removing
the DC source.
3. With the voltage regulator disconnected ( wires 3 and 4 ), start the prime mover and measure the “ residual ” voltage available at the auxiliary winding. If this voltage is greater than 5 Vac, reconnect voltage regulator, and voltage build-up should be successful. If less than 5 Vac is measured, repeat field flashing procedure.
4. If repeating steps a. and b. does not result in
generator voltage build-up, and residual is greater than 5 Vac, replace voltage regulator.

Package Including:
1 × Automatic Voltage Regulator Controller AVR EA05A Genset Parts
1×Product Instructions

Item SpecificsCountry of Origin United StatesBrand findmallMPN EA05AType Automatic Voltage RegulatorQuantity 1 PCModel EA05AEquipment Type Voltage RegulatorWarranty 1 Year
Introduction of Promotion

Fold over fold

Payment

Shipping

Usually your Items will be shipped within 1-3 business day after your payment is cleared.

Returns

Refund is valid within 30 days after thepayment date

Item must be returned in original packing same as reached

Contact Us If you are satisfied with the product you received,please leave us positive response and 5 scores .Please give us the opportunity to resolve any problem. We understand the concerns and frustrations you might have, and will try our best to resolve the issues.We care about our valued customers, and will always try to help you.

CNCHand ToolsMetalworking SuppliesGenerator AccessoriesIndustrial Control Module Automatic Voltage Regulator Control Panel AVR EA05A For Generator Genset

Description:
Sensing Inpuuut
Voltage 220 / 380 / 440 VAC, 1 phase2 wire
DIP switch selectable
Frequency 50 / 60 Hz, DIP switch selectable
Power Input
Voltage 100 ~ 300 VAC, 1 phase 2 wire
Output
Voltage Max. 90 VDC @ 240 VAC input
Current Continuous 5A
Intermittent 7A for 10 sec
Resistance Min. 15 ohm Max. 100 ohm
Voltage Regulation
< ± 0.5% ( with 4% engine governing )
Voltage Build-up
Residual voltage at AVR terminal > 5 VAC
Thermal Drift
0.03% per °C change in AVR ambient
External Volts Adjustmen
± 7% with 1K ohm 1 watt trimmer
EMI Suppression
Internal electromagnetic interference filtering
Unit Power Dissipation
Max. 8 watt
Under Frequency Protection (Factory Setting)
60 Hz system presets knee point at 55 Hz
50 Hz system presets knee point at 45 Hz
Soft Start Ramp Time
3 sec.
Dimensions
101mm L * 69mm W * 47.5mm H
Weight
183g ± 2%
2. Wiring
When generator supply is over load, N phase will be different with the sharing load by 3 phases (load imbalance). Hence, the voltage from N phase to 3 phases (R.S.T.) will be altered. When the rated voltage of the traditional single input’s AVR is above 220V, it will increase the voltage drift rate by using N phase as the detective input. It will also cause the voltage imbalance.
EA05A can improve the above situation, and increase the generator’s rated voltage usage space,such as 380V, 440V. We can all detect by the “phase voltage”.
1. When the rated phase voltage of the generator is 220VAC, the input terminals B, C and sensing terminals A, C can join together. or connect independent.(as show as figure2).
2. When the rated phase voltage of the generator is 380V, 440V, the input terminals B, C and sensing terminals A, C must separate connect the wiring (as show as Figure 4 or figure 5). The voltage between B and C must not be over 300 VAC.
3. F+ F- terminals connect to the generator field. (J and K) FEXT.VR is the potentiometer (1KΩ 1W). These two terminals must be by-pass when external potentiometer is needless.
P.S. : A, B, C, F+ F- the usage of wire gauge are AWG16 or 1.25 mm2 85。
C above 600V.
The EXT.VR connection wires must be made of isolated wiring.
3. Adjustments
The voltage setting for 220V/380V/440V and the
frequency setting for 50/60HZ is show in figure7.
Please check the voltage/frequency selector setting
is correct before start the generator.

Caution:
The Generator Or Avr May Be Damaged
If The Voltage / Frequency Selector
Setting Is Incorrect.
Ufro Dip:
1. Before you turn on the generator, please turn the
voltage adjustment and stability adjustment full anti-clockwise. After the generator is on and run stably, turn the voltage adjustment clockwise to reach the required out voltage. (If there is an external potentiometer, turn the external potentiometer to the middle position before adjust internal voltage potentiometer.)
2. Adjust “Stability Adjustment” clockwise slowly to
change the response time between AVR and the generator. If the adjustment is too big, it might cause the voltage instable. If too small, the load voltage will change too much at heavy load. Our suggestion is to trace by the multi-meter DCV. To adjust “stability adjustment”, you
just need to make the multi-meter waving smaller. It can also improve the full load’s voltage drift rate.
4. Field Flashing
When the regulator is operated with the generator for
the first time, the polarity of residual magnetism may be reversed or too small to achieve the necessary build-up voltage for the regulator. If reversing the field connections does not induce build-up, and the residual voltage is less than the specified value of 5 Vac, shut down the Prime-mover and proceed with the following steps :
1. With the Prime-mover at rest and the regulator’s
field output wires disconnected, apply a DC source ( NOT grounded ) of not more than 3~12 Vdc with Positive to F+ and Negative to F-, in series with a current-limiting resistor of 3~5 ohms 20 watt. (The set battery is a suitable source.)
2. Allow approximately 3 seconds before removing
the DC source.
3. With the voltage regulator disconnected ( wires 3 and 4 ), start the prime mover and measure the “ residual ” voltage available at the auxiliary winding. If this voltage is greater than 5 Vac, reconnect voltage regulator, and voltage build-up should be successful. If less than 5 Vac is measured, repeat field flashing procedure.
4. If repeating steps a. and b. does not result in
generator voltage build-up, and residual is greater than 5 Vac, replace voltage regulator.

Package Including:
1 × Automatic Voltage Regulator Controller AVR EA05A Genset Parts
1×Product Instructions

Item SpecificsCountry of Origin :United StatesBrand :findmallMPN :EA05AType :Automatic Voltage RegulatorQuantity :1 PCModel :EA05AEquipment Type :Voltage RegulatorWarranty :1 Year
Introduction of Promotion

Fold over fold

Payment

Shipping

Usually your Items will be shipped within 1-3 business day after your payment is cleared.

Returns

Refund is valid within 30 days after thepayment date

Item must be returned in original packing same as reached

Contact Us If you are satisfied with the product you received,please leave us positive response and 5 scores .Please give us the opportunity to resolve any problem. We understand the concerns and frustrations you might have, and will try our best to resolve the issues.We care about our valued customers, and will always try to help you.

All rights reserved.

Hot Item 100 Pack 4-1/2\" × 7/8\'\' 40 Grit T29 Premium Zirconia Sanding Grinding Flap Discs USD 51.91 12V to 24V 15A 360W Waterproof DC/DC Car Voltage Converter Step Up Regulator USD 16.93 3HP SPL Electric Motor Air Compressor 3450RPM 56Frame 1Phase 115/230v 5/8\"Shaft USD 116.32 4 Piece 4 Inch Heavy Duty Caster Set Wheels Fits For All Swivel & Brake Casters USD 20.49 ER11/ER16/ER20/ER25/ER32/ER40 Spring Collet Set For CNC Milling Lathe Machine USD 16.81 New List Item HSK63A ER16A Collet Chuck 100mm G2.5 Balanced 30000 RPM CNC Tool Holder USD 46.59 MT6 - MT5 Adapter Sleeve Precision Ground Hardened Reducing Sleeve USD 82.70 7PCS 5/8\" Indexable Caroffere Turning Threading Lathe Tool + Insert USD 95.00 2PC CAT50 ER16 Collet Chucks 6\" Extended Length Tool Holders USD 84.07 Precision Compound Sine Plate 6 x 6 x 3-1/8 Inch .0002\" Accuracy Machinist Tool USD 175.03 Store CategoryStore Home CNC◈Edge Finder◈Drill Bits◈Spring Collet◈Boring Bar◈Mandrel◈Collet Chuck◈Pull Stud◈Quick Change Tool Post◈Drill Chuck◈Drill Chuck Arbors◈Live Center◈Vise◈Milling Mills◈Other Hand Tools◈Rivet Gun◈Wrenches◈Hydraulic Crimper◈Drill Bits◈Outside Micrometer◈Casters◈Other Metalworking & Manufacturing◈Sanding Disc◈Metal Cut Off Wheels◈Flap Discs◈Hose Clamp◈Welding Wire◈Cable◈Piston Driver◈Other Generator Accessories◈Automatic Voltage Regulator◈Generator Carburetor◈Other Industrial Control Module◈Control Valves◈Roller Chain◈Other◈Electric Motor Decorate◈Conduit Corrugated◈Interior door fittings◈Decoration materials◈Paint Sprayers◈Other Construction Machinery▷Excavator Parts♢Excavator Carburetor♢Engines & Engine Parts♢Seat♢Other Excavator Parts▷Truck Parts♢Tow Chain♢Other Agricultural Equipment▷Tractor Parts♢Other Tractor Parts◈Farm Machinery Accessories Hot-Sale Products Findmall Peripheral Products Brand New Products Other

On Nov 1, 2026 at 19:42:13 PST, seller added the following information: