Automatic Voltage Regulator AVR EA05A Control Panel Generator Controller

Key Features：

Automatic Voltage Regulator AVR EA05A Control Panel Generator Controller

Key Features：

Sensing Inpuuut
Voltage 220 / 380 / 440 VAC, 1 phase2 wire
DIP switch selectable
Frequency 50 / 60 Hz, DIP switch selectable
Power Input
Voltage 100 ~ 300 VAC, 1 phase 2 wire
Output
Voltage Max. 90 VDC @ 240 VAC input
Current Continuous 5A
Intermittent 7A for 10 sec
Resistance Min. 15 ohm Max. 100 ohm
Voltage Regulation
< ± 0.5% ( with 4% engine governing )
Voltage Build-up
Residual voltage at AVR terminal > 5 VAC
Thermal Drift
0.03% per °C change in AVR ambient
External Volts Adjustmen
± 7% with 1K ohm 1 watt trimmer
EMI Suppression
Internal electromagnetic interference filtering
Unit Power Dissipation
Max. 8 watt
Under Frequency Protection (Factory Setting)
60 Hz system presets knee point at 55 Hz
50 Hz system presets knee point at 45 Hz
Soft Start Ramp Time
3 sec.
Dimensions
101mm L * 69mm W * 47.5mm H
Weight
183g ± 2%
2. Wiring
When generator supply is over load, N phase will be different with the sharing load by 3 phases (load imbalance). Hence, the voltage from N phase to 3 phases (R.S.T.) will be altered. When the rated voltage of the traditional single input’s AVR is above 220V, it will increase the voltage drift rate by using N phase as the detective input. It will also cause the voltage imbalance.
EA05A can improve the above situation, and increase the generator’s rated voltage usage space,such as 380V, 440V. We can all detect by the “phase voltage”.
1. When the rated phase voltage of the generator is 220VAC, the input terminals B, C and sensing terminals A, C can join together. or connect independent.(as show as figure2).
2. When the rated phase voltage of the generator is 380V, 440V, the input terminals B, C and sensing terminals A, C must separate connect the wiring (as show as Figure 4 or figure 5). The voltage between B and C must not be over 300 VAC.
3. F+ F- terminals connect to the generator field. (J and K) FEXT.VR is the potentiometer (1KΩ 1W). These two terminals must be by-pass when external potentiometer is needless.
P.S. : A, B, C, F+ F- the usage of wire gauge are AWG16 or 1.25 mm2 85。
C above 600V.
The EXT.VR connection wires must be made of isolated wiring.
3. Adjustments
The voltage setting for 220V/380V/440V and the
frequency setting for 50/60HZ is show in figure7.
Please check the voltage/frequency selector setting
is correct before start the generator.

Features & Details：

Caution:
The Generator Or Avr May Be Damaged
If The Voltage / Frequency Selector
Setting Is Incorrect.
Ufro Dip:
1. Before you turn on the generator, please turn the
voltage adjustment and stability adjustment full anti-clockwise. After the generator is on and run stably, turn the voltage adjustment clockwise to reach the required out voltage. (If there is an external potentiometer, turn the external potentiometer to the middle position before adjust internal voltage potentiometer.)
2. Adjust “Stability Adjustment” clockwise slowly to
change the response time between AVR and the generator. If the adjustment is too big, it might cause the voltage instable. If too small, the load voltage will change too much at heavy load. Our suggestion is to trace by the multi-meter DCV. To adjust “stability adjustment”, you
just need to make the multi-meter waving smaller. It can also improve the full load’s voltage drift rate.
4. Field Flashing
When the regulator is operated with the generator for
the first time, the polarity of residual magnetism may be reversed or too small to achieve the necessary build-up voltage for the regulator. If reversing the field connections does not induce build-up, and the residual voltage is less than the specified value of 5 Vac, shut down the Prime-mover and proceed with the following steps :
1. With the Prime-mover at rest and the regulator’s
field output wires disconnected, apply a DC source ( NOT grounded ) of not more than 3~12 Vdc with Positive to F+ and Negative to F-, in series with a current-limiting resistor of 3~5 ohms 20 watt. (The set battery is a suitable source.)
2. Allow approximately 3 seconds before removing
the DC source.
3. With the voltage regulator disconnected ( wires 3 and 4 ), start the prime mover and measure the “ residual ” voltage available at the auxiliary winding. If this voltage is greater than 5 Vac, reconnect voltage regulator, and voltage build-up should be successful. If less than 5 Vac is measured, repeat field flashing procedure.
4. If repeating steps a. and b. does not result in
generator voltage build-up, and residual is greater than 5 Vac, replace voltage regulator.

Package Content：

1 × AVR EA05A

Notes：

The Product Has Passed Strict Quality Testing

Durable And Easy To Install And Replace

Cost-Effective, The Best After-Sales Service

Quality Assurance For Your Peace Of Mind

Item SpecificsCountry of Origin United StatesBrand findmallMPN EA05AEquipment Type Voltage RegulatorModel EA05AType Automatic Voltage RegulatorWarranty 3 MonthsQuantity 1 PC
Payment

We ship to your address. Please make sure your address is correct before you pay.

Shipping

We handle orders within 24 hours at Monday to Friday and Saturday forenoon. weekend orders will be shipped at next monday

Returns

pls send return tracking number and time to me after return, keep tracking on the way, thank you.
Buyer are responsible for check correct part,thanks.
We will do the same response to you when we receive your response, thank you.

Contact Us

You can return your unused items back for exchange or refund within 30 days.
If the parts are damaged on the way or have fault, pls send problem description or take picture about problem, send description or picture to me by message, we will check the questions and solve it for you ASAP, thank you.

DESCRIPTIONPAYMENTSHIPPINGRETURN POLICYCONTACT US Shop CategoryStore Home Business & Industrial▷Handling & Storage ♢Transport And stack equipment♢Slings♢Cargo Packaging♢Casters♢Lifting Equipment♢Ladders And Work Platforms▷Pumps, Valves & Pipes♢Pumps ♢Industrial Hoses ♢Oil Transfer▷Warehousing & Management♢Operating Equipment▷Low Voltage Distribution♢Electrical Components ♢Power Generation Equipment▷Electrical Controls♢Cabinet▷Power Transmission♢Motors ♢Slide Guide Screws ♢Chain Sprockets ♢Bearings & Tools▷Power Tools♢Electrical Tools ♢Power Tool Supplies ♢Pneumatic Tools ♢Hydraulic Tools▷Personal Protection♢Work Gloves▷Welding Machines♢Welding Parts ♢Assemblies▷Pneumatics & Hydraulics♢Power Tool Accessory Parts ♢Hydraulic Pumps ♢Hydraulic Control Elements ♢Hydraulic Actuating Elements▷Cutting Tools♢Toolholding Systems ♢Sharpening Tools ♢Drill Pin Tools▷Hand Tools♢Wrench Kits♢Plumbing Tools ♢Clamps ♢Screwdrivers & Bits♢Pliers ♢Plier Tools ♢Painting Tools▷General Purpose Equipment ♢Small Mechanical Equipment Inspection ♢Process Instrumentation▷Refrigeration ♢Heating And Heat Supply♢Ventilation And Cooling ♢Refrigeration Equipment▷Renovation Support♢Sanitary Ware And Hardware♢Decorative Substrates▷Industrial Lighting♢Lighting Fixtures◈Other Home & Garden▷Lawn Kits♢Transmission System♢Ignition Coil♢Mower Spindle♢Mower Starter♢Lawn Mower Seat♢Lubrication System♢Recoil Starter♢Solenoid♢Air Blower♢Leaf Blower Accessories▷Snow Blower♢Snow Blower Accessories▷Garden Tool♢Courtyard Garden Facilities♢Water Pipe♢Grass Repellent Cloth♢Braided Rope♢Nursery Cup♢Extension ladder♢Gallon Basin▷Outdoor Sports♢Sports Equipment♢Swimming pool supplies▷Other Tool♢Other Tool Accessories Commercial Machinery▷Construction Machinery♢Excavator Parts♢Truck Parts▷Forestry Equipment♢Tractor Parts♢Plant and breed equipment♢other OtherHot Item 1/4\" - 3/8\" Dia. 50 Feet Install Kit Mini Split Line Connection Accessory Kit USD 126.33 For Kohler Fuel Pump Module Kit with Fuel Filter 2539316-S 2539316 2539314 USD 27.11 587819701 187292 532187292 532187281 Spindle Assembly For Husqvarna Craftman USD 19.47 25 FT 3/8\" & 5/8\" Mini Split Line Set Cooling Connection Pipe Install Kit USD 113.55 Gasket Set For Kohler K241 K301 K321 10 12 14 hp Engines 47 755 08-S Lawn Mower USD 10.33 Picture

New List Item Driveway Markers Snow Stakes Orange 100 Pack of 6 feet Long Reflective markers USD 72.62 100× Orange Reflective Markers Driveway Markers Snow Stakes 6Feet 5/16\" Diameter USD 72.60 40,000 Gallons Fit For Hayward-W3T-CELL-15 Salt Cell with 15-ft Cable - USD 222.08 Portable Shallow Well Pump Garde Pump Sprinkler Pump 1209 GPH 115V 1.2 HP USD 67.69 071314S 355010S Square Flange Motor Pool Pump Motor 1HP Single Speed 3450 RPM USD 142.85 Help & InfoPayment PolicyShipping PolicyReturn PolicyFAQAbout Us Automatic Voltage Regulator AVR EA05A Control Panel Generator Controller

Key Features：

Sensing Inpuuut
Voltage 220 / 380 / 440 VAC, 1 phase2 wire
DIP switch selectable
Frequency 50 / 60 Hz, DIP switch selectable
Power Input
Voltage 100 ~ 300 VAC, 1 phase 2 wire
Output
Voltage Max. 90 VDC @ 240 VAC input
Current Continuous 5A
Intermittent 7A for 10 sec
Resistance Min. 15 ohm Max. 100 ohm
Voltage Regulation
< ± 0.5% ( with 4% engine governing )
Voltage Build-up
Residual voltage at AVR terminal > 5 VAC
Thermal Drift
0.03% per °C change in AVR ambient
External Volts Adjustmen
± 7% with 1K ohm 1 watt trimmer
EMI Suppression
Internal electromagnetic interference filtering
Unit Power Dissipation
Max. 8 watt
Under Frequency Protection (Factory Setting)
60 Hz system presets knee point at 55 Hz
50 Hz system presets knee point at 45 Hz
Soft Start Ramp Time
3 sec.
Dimensions
101mm L * 69mm W * 47.5mm H
Weight
183g ± 2%
2. Wiring
When generator supply is over load, N phase will be different with the sharing load by 3 phases (load imbalance). Hence, the voltage from N phase to 3 phases (R.S.T.) will be altered. When the rated voltage of the traditional single input’s AVR is above 220V, it will increase the voltage drift rate by using N phase as the detective input. It will also cause the voltage imbalance.
EA05A can improve the above situation, and increase the generator’s rated voltage usage space,such as 380V, 440V. We can all detect by the “phase voltage”.
1. When the rated phase voltage of the generator is 220VAC, the input terminals B, C and sensing terminals A, C can join together. or connect independent.(as show as figure2).
2. When the rated phase voltage of the generator is 380V, 440V, the input terminals B, C and sensing terminals A, C must separate connect the wiring (as show as Figure 4 or figure 5). The voltage between B and C must not be over 300 VAC.
3. F+ F- terminals connect to the generator field. (J and K) FEXT.VR is the potentiometer (1KΩ 1W). These two terminals must be by-pass when external potentiometer is needless.
P.S. : A, B, C, F+ F- the usage of wire gauge are AWG16 or 1.25 mm2 85。
C above 600V.
The EXT.VR connection wires must be made of isolated wiring.
3. Adjustments
The voltage setting for 220V/380V/440V and the
frequency setting for 50/60HZ is show in figure7.
Please check the voltage/frequency selector setting
is correct before start the generator.

Features & Details：

Caution:
The Generator Or Avr May Be Damaged
If The Voltage / Frequency Selector
Setting Is Incorrect.
Ufro Dip:
1. Before you turn on the generator, please turn the
voltage adjustment and stability adjustment full anti-clockwise. After the generator is on and run stably, turn the voltage adjustment clockwise to reach the required out voltage. (If there is an external potentiometer, turn the external potentiometer to the middle position before adjust internal voltage potentiometer.)
2. Adjust “Stability Adjustment” clockwise slowly to
change the response time between AVR and the generator. If the adjustment is too big, it might cause the voltage instable. If too small, the load voltage will change too much at heavy load. Our suggestion is to trace by the multi-meter DCV. To adjust “stability adjustment”, you
just need to make the multi-meter waving smaller. It can also improve the full load’s voltage drift rate.
4. Field Flashing
When the regulator is operated with the generator for
the first time, the polarity of residual magnetism may be reversed or too small to achieve the necessary build-up voltage for the regulator. If reversing the field connections does not induce build-up, and the residual voltage is less than the specified value of 5 Vac, shut down the Prime-mover and proceed with the following steps :
1. With the Prime-mover at rest and the regulator’s
field output wires disconnected, apply a DC source ( NOT grounded ) of not more than 3~12 Vdc with Positive to F+ and Negative to F-, in series with a current-limiting resistor of 3~5 ohms 20 watt. (The set battery is a suitable source.)
2. Allow approximately 3 seconds before removing
the DC source.
3. With the voltage regulator disconnected ( wires 3 and 4 ), start the prime mover and measure the “ residual ” voltage available at the auxiliary winding. If this voltage is greater than 5 Vac, reconnect voltage regulator, and voltage build-up should be successful. If less than 5 Vac is measured, repeat field flashing procedure.
4. If repeating steps a. and b. does not result in
generator voltage build-up, and residual is greater than 5 Vac, replace voltage regulator.

Package Content：

1 × AVR EA05A

Notes：

The Product Has Passed Strict Quality Testing

Durable And Easy To Install And Replace

Cost-Effective, The Best After-Sales Service

Quality Assurance For Your Peace Of Mind

Item SpecificsCountry of Origin :United StatesBrand :findmallMPN :EA05AEquipment Type :Voltage RegulatorModel :EA05AType :Automatic Voltage RegulatorWarranty :3 MonthsQuantity :1 PC

PaymentShippingReturnsContact UsAbout Us

We ship to your address. Please make sure your address is correct before you pay.

We handle orders within 24 hours at Monday to Friday and Saturday forenoon. weekend orders will be shipped at next monday

pls send return tracking number and time to me after return, keep tracking on the way, thank you.
Buyer are responsible for check correct part,thanks.
We will do the same response to you when we receive your response, thank you.

You can return your unused items back for exchange or refund within 30 days.
If the parts are damaged on the way or have fault, pls send problem description or take picture about problem, send description or picture to me by message, we will check the questions and solve it for you ASAP, thank you.

All rights reserved.

On Nov 10, 2026 at 19:09:33 PST, seller added the following information: