ABS CONTROL MODULE FOR JEEP WRANGLER JK 2014–2018 · OE 68259556AD ⚠️ FITMENT NOTE — 2014–2018 JEEP WRANGLER JK (BUILT 06/30/2014 & AFTER)
This ABS module fits 2014–2018 Jeep Wrangler JK with the 3.6L V6 (VIN G) built on or after June 30, 2014. It does NOT fit earlier 2014 builds, 2010–2013 JK, Jeep Compass / Patriot, diesel models, or non-Jeep applications. You must verify the OE number on your original module and your vehicle build date before ordering. A factory ABS module is NOT plug-and-play from the box—it must be programmed to your VIN unless this listing specifies pre-programmed service. Contact us if you are unsure about programming requirements. PRODUCT DESCRIPTION
This ABS control module is a replacement for 2014–2018 Jeep Wrangler JK (3.6L V6, VIN G) built on or after June 30, 2014 that uses OE number 68259556AD (supersedes 68259556AA / AB / AC). The original module is a known failure point on the JK platform—common symptoms include ABS warning light, ESP/BAS light, C2200 code, loss of ABS function, and intermittent or complete failure of stability control. This module has been tested before shipping and is backed by a 12-month replacement warranty. It is a stock replacement (non-performance) component. Professional installation is recommended; programming/calibration is required unless the listing specifies pre-programmed “Plug & Play” service. ABS is a safety-critical system—do not drive the vehicle until the module is properly installed, programmed/calibrated, and all warning lights are off.
COMPATIBILITY MATRIX Make Model Year Engine Note Jeep Wrangler / Wrangler JK 2014–2018 3.6L V6 (VIN G) Built 06/30/2014 & after; 2-Door & 4-Door
⚠️ Does NOT fit 2014 builds before 06/30/2014, 2010–2013 JK, Jeep Compass / Patriot, diesel, or non-Jeep applications. 68067059AB is a Compass / Patriot number and is NOT compatible with Wrangler JK.
OE / INTERCHANGE PART NUMBERS 68259556AD · 68259556AC · 68259556AB · 68259556AA · 68259556AE
This is an aftermarket replacement / remanufactured ABS module. It is not a Genuine Mopar part. OE numbers are listed for cross-reference only. INSTALLATION NOTES
- Disconnect the battery negative terminal. Locate the ABS module in the engine bay (mounted to the ABS pump/hydraulic unit).
- Disconnect the electrical connector(s). Remove the mounting bolts and carefully separate the module from the pump. Note the orientation and connector pin arrangement.
- Compare the new module’s connector, mounting flange, and part number to the original before installation.
- Install the new module and reconnect the electrical connector. Tighten fasteners to factory specification.
- Program / calibrate the module to your VIN using a compatible scan tool (JScan, WiTech, or dealer software) unless the listing specifies pre-programmed “Plug & Play” service.
- Start the engine and verify that all ABS / ESP / BAS warning lights are off. Test ABS operation in a safe area. Clear any stored codes.
📦 WHAT'S IN THE BOX
Mounting hardware and diagnostic programming are NOT included.
📏 SHIPPING SPECS
- Packing Size: Approx 22 × 18 × 14 cm
- Weight: Approx 1.0–1.5 kg
⚠️ IMPORTANT NOTICE
Please verify the part number (OE number) carefully before placing your order. Should you have any questions, please contact our customer service team.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.