5 PCS SG90 9g Servo Motor PCA9685 IIC 12Bit 16 Channel PWM Controller Module 5 PCS SG90 9g Servo Motor PCA9685 IIC 12Bit 16 Channel PWM Controller ModuleTracked U.S. Shipping Quality Checked48-State ShippingCareful PackagingCarrier TrackingSafe CheckoutKey Features
- SG90 9g Servo:Operating Voltage:4.8-6V
- Running angle:180°±1° (500→2500 μsec)
- PCA9685 Servo Controller Module:Voltage: DC 5-10V
- Frequency: 40-1000Hz
- Commodities include:1Pcs PCA9685 Servo Controller Module;5Pcs SG90 9G servo
About the ProductProduct Overview
SG90 9G servo
Working voltage: 4.8-6V
Rotation angle: 180°±1° (500 - 2500 μsec)
Stalling torque: 1.3kg/cm - 1.6kg/cm (4.8V)
Stalling current: 750mA±10%
Pulse width: 500~2500μsec
Midpoint position: 1500μsec return error ≤1%
No-load speed: 0.09 seconds/60°
No-load current: 90mA
Response speed: 0.3 seconds/60°
Dead zone width: 8 microseconds
Gear material: nylon
Using temperature: 0-55 degrees
PCA9685-16-channel PWM servo driver module
This is an I2C communication module with built-in PWM driver and clock. This means that it is very different from the TLC5940 series. You don\'t need to keep sending signals to occupy the microcontroller.
It is compatible with 5V voltage, which means you can also use a 3.3V microcontroller to control and drive its output to 6V (it is also feasible when you want to control the white or blue indicator light with a positive voltage above 3.4V)
Parameters:
Frequency: 40-1000Hz
Number of channels: 16 channels
Resolution: 12 bits
Voltage: DC 5-10V
1.6 address selection pins allow you to mount 62 driver boards on a single I2C bus, with a total of 992 PWM outputs. This will be a very huge resource.
2. 1.6KHz adjustable frequency PWM output
3. Stepper motor resolution is 12 bits, which means the resolution is 4us at 60Hz update rate
4. Configurable push-pull or open-circuit output, output enable pin can quickly disable all outputs
Features:
1. PCA9685 chip is encapsulated in the power input terminal of the small board, green power indicator
2. 4 groups of 3-pin connectors, convenient for you to insert 16 servos at a time (servo plug is slightly wider than 0.1 inches, so you can insert 4 pairs of 0.1-inch connectors)
3. The terminal input has reverse polarity protection
4. Put a large capacitor on the V+ line (it will be needed in some cases), the peripheral input voltage depends on this 10V1000uf capacitor
5. Connect a 220 ohm resistor in series on all PWM output lines to protect them and drive LEDs easily
Commodities include:
1Pcs PCA9685 Servo Controller Module
5Pcs SG90 9G servo
Compatible with Arduino, Raspberry Pi remote control car boat helicopter airplane robot model control DIY
Delivery Information
Every order is prepared with care and shipped with carrier tracking across the 48 contiguous United States. For buyer protection, parcels ship strictly to your verified checkout address.
Return Policy
Shop with complete peace of mind. Returns are gladly accepted within 30 days of delivery. Returned items should remain unused, complete, and in original packaging to qualify for a refund.
Payment Options
Checkout is safely managed via official Payments, accepting major credit cards, PayPal, Apple Pay, and Google Pay.
Your response Matters
Happy with your new item? Leaving positive response encourages our shop and helps other buyers shop confidently.
Contact Information
Questions about product details or your delivery? Message us anytime through Messages for prompt help.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.