Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

220V 3.8KW Stacked Arm Curve Edge Banding Machine Rocker Arm/Foldable Arm Curved

220V 3.8KW Stacked Arm Curve Edge Banding Machine Rocker Arm/Foldable Arm Curved
$2,088.99

Buy Now

220V Rocker Arm/Foldable Arm Curved Edge Banding Machine

Product OverviewThe rocker arm curved edge banding machine is a special device for edge banding of boards in different shapes, the functions of edge banding, timing strip breakage, powerful suction, auxiliary hot air and so on can be fulfilled on one machine, the operating difficulty and complexity are greatly reduced, and the edge sealing performance, the attractiveness and the durability of boards can be well improved. The machine can be widely applied to the industries of cabinet manufacturing, wooden door production, home customization and so on.Product ParametersModelF11-3Voltage220V 50Hz Single-phase electricityTotal power3.8KwAir pressure0.6-0.8MpaEdge Strip width14-70mmEdge Strip thickness0.5-2mm (related to edge strip materials)Edge banding speed0-24cm/sEdge band materialsPVC, veneer, melamine, plastic, etc.Board shapeCircular boards, square boards, triangular boards, L-shaped boards, etc.Board sizeCircular board≤1.6m,Square board≤1x1.5m, L-shaped board≤1.2x1.2mApplicable boardsPlywood boards, acrylic boards, chipboards, block boards, density boards, etc.Operation Instructions

Temperature Regulation


Firstly, adjust the temperature until the hot melt glue has slight smoke, and then reduce the temperature by 5-10 degrees every 5-10 minutes. When the machine is used for the first time or each time another hot melt glue is replaced, the temperature must be reset. When the temperature reaches the set temperature, the motor can be started.

 

Motor Control


When the temperature reaches the set temperature, the motor can be started. The motor may be overheated when the speed is below 30 for a long period of time. The edge banding speed can be 0-24cm/s.

Attention1. The machine must be reliably grounded.2. Please check the amount of the remaining hot melt glue in the glue pot before use.3. When any abnormal situation occurs in the working process, please press the emergency stop switch immediately.4. Non-professionals are prohibited from operating and repairing the machine.5. When disassembling and repairing the machine, first turn off the power and then wear protective tools.6. When inspecting the circuit, be sure to completely disconnect the power supply, otherwise there is still electricity in the circuit!7. The machine needs to be connected with an air compressor which needs to be prepared by the customer.Product Features

Foldable Arm & Suction Disc


The suction disc has the high suction so that the board can be firmly sucked onto the suction disc and prevented from being suspended in the air or falling off. Meanwhile, along with the flexible movement of the foldable arm, the board on the suction disc can be pushed to be subjected to edge banding operation. The foldable arm can be folded and unfolded at any during the edge banding operation, time and labor are greatly reduced, and the practicability is greatly improved.

 

Control Panel


The multifunctional control panel is designed for the machine and can fulfill multiple functions, such as power supply, emergency stop, temperature regulation, motor speed regulation and curve timing. The user can accurately control and adjust different parameters according to board processing requirements. Digital display is clear and obvious, and the production efficiency can be obviously improved.

 

Oil-water Separators


The machine is equipped with two oil-water separators, one oil-water separator is used for controlling the cutter and the strip moving plate, and the other is used for controlling the suction disc. The two oil-water separators control different parts correspondingly and ensure the accurate air pressure and smooth operation. The oil-water separators should be adjusted before edge banding operation is conducted.

Auxiliary Hot Air Device


The device can be used for heating and softening the edge banding strip so that the edge banding strip and the board can firmly glued together. The outlet air angle can be adjusted freely and flexibly by loosening and tightening the nut. The edge banding strip is not prone to be separated from the board, the edge banding effect can be well improved, and the bonding firmness can be higher.

 

Glue Coating Part


The heightened glue coating assembly adopts a high-temperature-resistant bearing and sealing rings, achieves single-sided glue coating of the edge banding strip, thereby saving the hot melt glue and being small in glue line. The 2800ml large-capacity glue pot avoids frequent addition of the hot melt glue, thereby greatly reducing the labor intensity. The lengthened knob facilitates the glue quantity adjustment, and operation is more convenient and easier.

 

Dual Foot Pedals


The design of double foot pedals is adopted, one foot pedal can control the suction of the suction disc, and the other foot pedal can control strip feeding and breakage of the edge banding strip. Two hands of the user are liberated, the functions are clear and accurate, the operating complexity and difficulty are greatly reduced, and the user experience is good.

Strip Moving Plate


The novel strip moving plate can prevent the edge banding strip from moving in the reverse direction, and the edge banding strip can be fed stably and smoothly and is not prone to deviation. The strip moving plate facilitates feeding movement of the edge banding strip and well assist in edge banding operation.

 

Cutter Assembly


The cutter assembly can make a very quick response and ensures the cutoff perpendicular precision. The cutter is stable through the double column balance, the structure is compact, and the cutoff flatness and the cutting effect are good. The maximum strip cutting width can be 70mm, and the maximum strip cutting thickness can be 2mm.

 

Double Cylinders


Two cylinders are installed to fulfill different function control. One cylinder is used for controlling the cutter, and the other cylinder is used for controlling strip feeding operation. Independent control of different motions can be achieved by the cylinders, the control precision is high, and the control effect is good.

ApplicationThe rocker arm curved edge banding machine can be used for processing various boards in different shapes, can stick different edge banding strips such as PVC strips, plastic strips and melamine strips to the boards, can be widely applied to woodworking plants and workshops and has a good edge banding effect.Product DisplayItem Number (154069): 1 x Rocker Arm/Foldable Arm Curved Edge Banding Machine 220V

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design