新建网页 3 2-layer 1.9Cu ft Vacuum Drying Oven Intelligent Temperature Control for Lab 110V
This device is used for drying and heating processes under vacuum conditions at laboratories in enterprises,
schools and scientific institutions. Heating and drying under vacuum condition shows the following
advantages:
a. Drying temperature can be lowered. (Low pressure and low temperature).
b. Oxidation of some articles after heating can be avoided with no damages done by dust.
c. Slaughter of biological cells caused by heated air can be avoided.
Application Vacuum drying boxes are widely used in biochemistry, chemical and health, agricultural scientific research, environmental protection and other research and application fields, for powder drying, baking and disinfection and sterilization of all kinds of glass containers. It is especially suitable for rapid and efficient drying of heat-sensitive, easily decomposed, easily oxidized substances and complex components. Voltage 110V Power 1400W Temperature range 50~200℃ Temperature fluctuation ±1℃ Vacuum degree <133Pa Dwelling timer range 1-9999 minutes Studio Size 410*370*345mm
(16.14\"*14.57\"*13.58\")
Studio Materials 304 stainless steel The quantity of the shelves 2 Pumping rate of matching vacuum pump 2L
Intelligent temperature control
LCD backlight display,
Intelligent timing overtemperature alarm, Intelligent temperature correction
Toughened glass door
Upgraded and thickened explosion-proof vacuum glass
Silicone oil vacuum pressure gauge
Seismic, anti-magnetic, high precision, high temperature corrosion resistance stability
High temperature and thickened silicone sealing ring
Effectively prevent air leakage, to ensure that the door and the studio closely fit
offerirectional convective circulation system
Double partition board, each layer of air temperature uniform circulation space utilization rate, fast drying speed
Usage
1. Put the items that need to be dried into the box, close the box door and tighten the door handle, close
the return valve, open the vacuum valve, connect the air duct on the side of the vacuum drying box to
the vacuum pump with a vacuum rubber tube, connect the power to the vacuum pump, and start pumping.
When the vacuum gauge indicates the desired vacuum degree, close the vacuum valve first, and then turn
off the vacuum pump. At this time, the box is in a vacuum state.
2. After connecting the power, turn on the power switch and the indicator light will light up, indicating normal
operation. The instrument will display the temperature of the studio, and then adjust the control instrument
to the set temperature. The studio will start heating, and the green light on the control instrument will light
up, indicating power on and heating. After the instrument remains constant for 60 minutes, the temperature
displayed on the instrument should be basically consistent with the set temperature.
3. Choose different drying times for different items and temperatures. If the drying time is long and the
vacuum degree decreases, it is necessary to pump air again to restore the vacuum degree. The vacuum
pump should be turned on first, and then the vacuum valve should be opened.
4. After the drying is completed, the power should be turned off first, the return air valve should be turned on,
the vacuum inside the box should be released, and the box door should be opened to remove the items(After
contact with the vacuum, the rubber ring is tightly attached to the glass door, making it difficult to open the
box door. It will take some time for it to be easily opened).
5.In a vacuum state, the control temperature should not be lower than 50 ℃. If it is below 50 ℃, the
value tested by the standard thermometer is different from the inconsistent display values on the instrument
panel are a normal phenomenon. This phenomenon does not affect temperature control and temperature
above 50 ℃.
Precautions
1. The vacuum drying oven must be effectively grounded to ensure safety.
2. When the vacuum drying box does not need to be connected for air extraction, the vacuum valve should be
closed first, then the power supply of the vacuum pump should be turned off, and the vacuum pump air
ballast valve should be opened at the same time, otherwise the pump oil will pour back into the box.
3. When removing the processed item, if it is flammable, it must wait for the temperature to cool below the
ignition point before being released into the air to avoid combustion.
4. The vacuum box is not equipped with explosion-proof devices and explosive materials must not be placed
for drying.
5. If conditions permit, a filter should be installed between the vacuum box and the vacuum pump to prevent
humid gases from entering the vacuum pump.
6.There is a small hole on the top of the silicone oil gauge to ensure that the pointer points to 0. If it is inverted during transportation, there may be slight oil leakage, which is a normal situation. After drying, it can be used normally.
7.After the work is completed, be sure to take proper protective measures to prevent burns.
Item Number 110V 1.9Cu ft Vacuum Drying Oven--160646
Shipping & Handling
Default Shipping Cost or Free Shipping Information:
-
Default shipping cost or free shipping service is only for the lower 48 United States by UPS Ground or USPS. Other areas or needs other shipping ways, please contact us.
-
Buyers from Guam, Puerto Rico, Virgin Islands, American Samoa, Alaska, Hawaii, PO Boxes, APO/FPO addresses or other countries/areas,there WILL be extra shipping costs, please contact us for more detailed information.
-
Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer.
Handling Time:
Sales tax / Customs duties
Damage In Shipping
Return&Refund
If you are not 100% happy with your purchase, please contact Us. Please don\'t directly opened a request or case without informing us, or else, we will do some discounts on the warranty and other sales-services later on. Hope for your understanding.
Returns & Exchanges
-
All returns must be made within 30 days of delivery date. Items must be in new, unused condition, with all original materials included with the shipment. A partial refund may be applied for opened or damaged items, depending on the condition.
-
Items returned under the buyer’s remorse: The return shipping fee must be covered by the buyer; The original shipping cost will also be deducted from the refund. 15% restocking fee of the items purchase price will be charged.
-
Returns that are the result of our seller\'s error: Buyer will receive a full refund of the item as well as shipping charges
-
All returns require a RA (Return Authorization) number that will be given by our seller. Please contact with us at first for more details.
Defective & Damaged Products
-
If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it\'s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. Hope for your understanding.
-
Replacement or refund of defective or damaged products can only be returned in exchange for the exact same product, or else, the purchase price will be refunded back to your original payment method.
-
If an item is received damaged, customer service must be contacted within 7 days of receiving your item. All returns require a RA (Return Authorization) number as above.
Warranty&response
-
6 months\' warranty for the machines, not for the consumables. We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.
-
Any warranty shipping cost to us is responsible by buyer.
-
Any shipping cost to buyer is responsible by the seller.
-
We committee to the customer satisfaction and want to bring you the best purchase experience. If there is any problems, please contact us ASAP. If not, please leave us a positive response as it\'s very important for us. Thanks very much.
On Oct 22, 2025 at 20:09:31 PDT, seller added the following information:
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.