Free Userbar - Userbars - User Bar - User Bars
 
Advanced search
Registered users

Username:

Password:

Log me on automatically next visit?

¬ Forgot password
¬ Registration

» Upload Userbar
» Animate Userbar
» Userbars Tutorial
» Userbar Tournaments
» Forum
» Chat Room
» FAQ
» Links

• PC Cheat Codes

>> If you dont know how to design a userbar, then write here a Userbar that you want. >> If you know how to design them help these people and design what they request.




USERBARS.org | Free Forum Userbars

On eBay now
eBay

12V Wireless Remote Control Switch, DC 5-60V 1CH Dry Contact Relay

12V Wireless Remote Control Switch, DC 5-60V 1CH Dry Contact Relay
$31.99

Buy Now

Product description DC 5~60v Single Channel Controller Technical Parameters

Working Voltage : DC 5V/6V/12V/24V/36V/48V/60V

Modulation Mode:ASK

Matching Mode: Learning Code 1527.

Quiescent Current:5mA

Maximum load power: 300W

RF Frequency: 433MHz

Wiring method: NC COM NO

Circuit Board Size: 26 * 47 * 18mm

Output: single-channel passive switch quantity output

Max Relay Contact Current : DC 20A/AC 5A

About what is dry contact and how to wire it

This is a passive dry‑contact relay module.The receiver has three relay terminals: COM, NO and NC.

As a characteristic of dry‑contact design, these contacts will NOT output any voltage, even after the receiver is powered up.They work just like an ordinary mechanical switch.

To activate your load, you need a separate external power supply for the load (this power supply feeds the load, not the receiver), and wire COM with NO or NC to form a complete closed circuit so external current can pass through.

Recommended wiring logic:

  1. Route one side of your load power supply to the COM terminal
  2. Connect the NO terminal to one wire of your load
  3. Link the remaining wire of your load back to the other side of the external power supply to finish the full loop

How it works:

  • Remote OFF state: COM and NO stay open. No current flows, and the load remains off.
  • Remote ON state: COM and NO close. Current passes through the completed circuit, turning your load ON.

Troubleshooting

Case 1: Remote no response / relay never clicks

•The remote and receiver are not paired. Complete pairing following the user manual.

Case 2: Relay clicks, but the load still does not run

•Incomplete circuit, missing load power supply, or missing COM jumper.

About Working Modes-- Pick The Right One Before Pairing Momentary Pulse Mode

Press the remote button , the relay connects, release the remote button , the relay dis-connects.

For Example,

Relay stays ON only while holding the button; turns off once you release.

Momentary mode can be applied to electric door locks!

Toggle(Use Single Key)

Press once the remote button, the relay connects , press the remote button again, the relay dis-connects

For Example,

Press ON once to activate, press ON again to deactivate.

Latched (Interlock) – Recommended

Press the remote button ON, the relay connects, press the remote button OFF, the relay dis-connect.

For Example,

Two‑button independent control. Best choice if you need separate ON/OFF keys.

Latched mode can be applied to on/off car batteries!

Timed Delay Mode (5/10/15/20 Seconds)

Press the remote button , the output terminal of the receiver will be powered on for a certain time (5s/10s/15s/20s), and the output terminal of the receiver will be powered off.

For Example,

Press ON to activate relay, it automatically powers off after preset time.

Working Mode Settings

1.Reset : Press the learning button on the module 8 times continuously, and the light flashes seven times and then goes out.

2.Momentary Mode:Press Module learning button 1 time, the indicator light is always on, then press the remote control button, the indicator light flashes 3 times and then turns off , then the learning is successful; If the code is not successful , the indicator lights out of the learning state after 15 seconds .

3.Toggle Mode:Press the Module Learning button 2 times, the indicator light always turns on; then press the remote control button, the indicator lights flicker three times and then off, then the learning is successful; if the code has not been successful, the indicator lamp goes out of the study state after 15 seconds.

4.Latched Mode :Press the receiver button 3 times, the receiver indicator light is always on, the receiver enters the code matching state, and then press the remote control button, the receiver indicator light flashes and then stays on, then press another button on the remote control, after the code is successful, the indicator light goes out.

5.Delay Mode : Press a certain number of times (4 times correspond to 5s/ 5 times correspond to 10s/ 6 times correspond to 15s/ 7 times correspond to 20s) to press the receiver button, the receiver indicator light is always on, the receiver enters the code matching state, then press the key of the remote controller, and the indicator light will go out after the code matching is successful.

Important Note

Pair the remote and receiver only once! It will save the pairing forever — even if you turn off the power, you don’t need to pair again.

Q: Why the OFF button can’t turn my device off?

A: If you want separate ON & OFF control, clear codes and re‑pair under Latched mode.

Q: What is the difference between Toggle and Latched mode?

A: Latched mode has independent ON and OFF keys.

Toggle mode is single‑key toggle control, OFF button is inactive.

  • WIDE VOLTAGE COMPATIBILITY: Supports DC 5 V to 60 V input; fully compatible with 12 V, 24 V, 36 V, 48 V and 60 V low-voltage systems; features dry contact output with NO, NC and COM terminals; compact PCB measures 47 x 26 x 18 mm for tight-space installation
  • 4 PROGRAMMABLE WORKING MODES: Includes Momentary, Toggle, Latched and Delay Off modes; adjustable auto-off delay with 5 s, 10 s, 15 s and 20 s options; ideal for access control, lighting timing and car battery power management
  • STABLE SUPERHETERODYNE RECEPTION: Adopts superheterodyne receiving technology for strong anti-interference performance; delivers 50 m to 100 m transmission range in open areas; built-in antenna can be pulled out through the case hole for better signal reception
  • EXPANDABLE REMOTE PAIRING: Supports EV1527 learning code remote controls; pairs with up to 20 remote transmitters simultaneously; allows easy pairing of replacement remotes if the original is lost or damaged
  • WIDE APPLICATION SCENARIOS: Suitable for car battery control, garage doors, electronic gates, motorcycle alarms, car sunroofs, heating systems, LED lights and small appliances; simple wiring with clearly marked terminals; perfect for home automation and DIY electronic projects
  • Rated contact load: 20A at 14VDC, 5A at 250VAC; suitable for 12V 24V low-voltage DC load control.
  • Pre-wired with bare wire leads, compatible with twisting connection, wire nuts and crimp terminals for easy circuit integration.

Buy Now

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.


Related Userbars
       

More items on eBay

As an eBay Partner, userbars.org may earn a commission from qualifying purchases.



All userbars are property of respective authors.
Copyright © 2002 4homepages.de | Template © 2005 Bali Web Design