12V Automation Delay Multifunction Self-lock Relay Cycle Timer Module PLC Home

• Visit store
• Items for sale
• About us

Product Details

Module Functions:
User can select from below eight functions, by using the key buttons onboard.
User can select and save the set parameters. The set time is 1 second at minimum,
and precision is better than 0.1 second. The eight functions are as follows:

1)Close upon the set time: after power one, the delay time T1 reaches, and the relay closes.
T1 is adjustable between 0 second to 270 hours. When we feed CH1 a high level pulse signal,
the cycle repeats itself (the high level time lasts longer or equal to 20ms. Same applies to below).
2)Disconnect upon the set time: when the relay closes, the delay time T1 reaches, and the relay
opens. T1 is adjustable between 0 second to 270 hours. When we feed CH1 a high level pulse signal,
the cycle repeats itself.
3)Cycle Mode 1: after power on, the relay does not close at first. When T1 reaches, the relay closes. When T2 reaches, the relay opens. And the cycle goes on. T1 and T2 adjustable between 0 second to
270 hours. When we feed CH1 a high level pulse signal, the cycle repeats itself.
4)Cycle Mode 2: after power on, the relay immediately closes. When T1 reaches, relay opens; when
T2 reaches, the relay closes again, and the cycle goes on. When we feed CH1 a high level pulse signal,
the cycle repeats itself.
5)Self-lock relay mode: we feed CH1 a high level pulse signal, relay closes. When we again feed a high level pulse signal, the relay opens.
6)Trigger relay mode: we feed CH1 a high level signal, relay closes. When the high level finishes, the relay opens.
7)Limited cycle mode 1: on basis of function 3, we increase the cycles. Under this mode, T1 and T2 are adjustable between 0 second to 9999 second, the cycle is selectable between 1 to 9999 times.
8)Limited cycle mode 2: on basis of function 4, we increase the cycles. Under this mode, T1 and T2 are adjustable between 0 second to 9999 second, the cycle is selectable between 1 to 9999 times.

Connections:
Module control side: there are 3-wire interface, all interfaces are terminal
1, DC +:12V positive
2, DC-: power in negative
3, CH1: Input Detection Interface
Relay outputs: a 3-wire interface, all interfaces are terminal
1, NO: normal open (before relay closes, this pin is not connected. after relay closes, the pin short-connects with COM)
2, COM: Relay Common Interface
3, NC: Normal closed (before relay closes, this pin short-connect with COM. after relay closes, the pin is not connected )

Specification:
Size:66x40x1.5mm(approx)
Color: as the photos show.Package included:1x 12V Automation Delay Multifunction Self-lock Relay Cycle Timer Module PLC Home

• Payment Method
• Shipping Method
  • Payment must be received in 5 business days of sale closing.
  • Please leave note for your special request (e.g. Colors or Size) when you pay the order.
    
  • Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
  Shipping Policy

  1. We only ship to the confirmed address provided by . please make sure your address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
  2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
  3. All package need to wait 30 days,Please take care it.Less than 30 days,we can\'t take a refund.

  response

  We maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your concerns.