1-10PCS ESP32-C3 Super Mini WIFI Development Board USB-C Bluetooth For Arduino

• Home
• Electronic Component
• Chips
• Sensor
• Arduino Module
• Raspberry Pi

1-10PCS ESP32-C3 Super Mini WIFI Development Board USB-C Bluetooth For Arduino Popular Popular

Product Introduction

Product features:1. ESP32C3 SuperMini is an IoT mini development board based on the Espressif ESP32C3 WiFi/Bluetooth dual mode chip. ESP32-C3 is a 32-bit RISC-V CPU that includes an FPU (floating point unit) that can perform 32-bit single precision operations and has powerful computing power.3. It has excellent RF performance and supports IEEE 802.11 b/g/n WiFi and Bluetooth 5 (LE) protocols.4. The board comes with an external antenna to enhance the signal strength of wireless applications.5. It also has a compact and exquisite appearance combined with a single surface mount design.6. It is equipped with rich interfaces, with 11 digital I/Os that can be used as PWM pins and 4 analog I/Os that can be used as ADC pins.7. It supports four serial interfaces: UART, I2C, and SPI.There is also a small reset button and a boot loader mode button on the board.9. ESP32-C3 SuperMini is positioned as a high-performance, low-power, and cost-effective IoT mini development board, suitable for low-power IoT applications and wireless wearable applications.Parameter Description:CPU: ESP32-C3, 32-bit RISC-V single core processorOperating frequency: 160 MHzMain frequency: 160MSRAM: 400KBROM: 374KBADC: 2 * 12-bit SARADC, 6 channelsWiFi: 802.11b/g/n protocol, 2.4GhHz, supports Station mode, SoftAP mode, SoftAP+Station mode, hybrid modeBluetooth: BT 5.0Power consumption: Deep sleep power consumption is about 43 μ ARich on chip resources: 400KB SRAM, 384KB ROMRich interfaces: 1xI2C, 1xSPI, 2xUART, 11xGPIO (PWM), 4xADCSingle sided components, surface mount designClassic appearance, suitable for wearable devices and small projectsReliable security features: Encryption hardware accelerator supporting AES-128/256, hashing, RSA, HMAC, digital signature, and secure bootOn board LED blue light, GPIO8 pinSize: 22.52x18mmAttention:If external power supply is required, simply connect the external power supply+level to the 5V position and connect the GND to the negative pole. (Supports 3.3-6V power supply). Remember that when connecting to an external power source, USB cannot be connected, and only one can be selected between USB and external power supply.2. Please be careful not to short-circuit the positive and negative electrodes during welding, which may burn out the battery and equipment.Instructions for use:Enter download mode: Press and hold the BOOT button of ESP32C3, then press the RESET button, release the RESET button, and then release the BOOT button. At this point, ESP32C3 will enter download mode. (Every time you connect, you need to re-enter the download mode. Sometimes, if you press it once, the unstable port will disconnect, which can be determined by identifying the sound through the port.)Product List:1-10 X development board

• Payment must be received in 5 business days of sale closing.
• Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
• Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.

Shipping

• We maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you contact us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your concerns.

Refund

• All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can\'t take a refund.
• If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
• If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.

• Home
• Electronic Component
• Chips
• Sensor
• Arduino Module
• Raspberry Pi

1-10PCS ESP32-C3 Super Mini WIFI Development Board USB-C Bluetooth For Arduino

Product Introduction

Product features:1. ESP32C3 SuperMini is an IoT mini development board based on the Espressif ESP32C3 WiFi/Bluetooth dual mode chip. ESP32-C3 is a 32-bit RISC-V CPU that includes an FPU (floating point unit) that can perform 32-bit single precision operations and has powerful computing power.3. It has excellent RF performance and supports IEEE 802.11 b/g/n WiFi and Bluetooth 5 (LE) protocols.4. The board comes with an external antenna to enhance the signal strength of wireless applications.5. It also has a compact and exquisite appearance combined with a single surface mount design.6. It is equipped with rich interfaces, with 11 digital I/Os that can be used as PWM pins and 4 analog I/Os that can be used as ADC pins.7. It supports four serial interfaces: UART, I2C, and SPI.There is also a small reset button and a boot loader mode button on the board.9. ESP32-C3 SuperMini is positioned as a high-performance, low-power, and cost-effective IoT mini development board, suitable for low-power IoT applications and wireless wearable applications.Parameter Description:CPU: ESP32-C3, 32-bit RISC-V single core processorOperating frequency: 160 MHzMain frequency: 160MSRAM: 400KBROM: 374KBADC: 2 * 12-bit SARADC, 6 channelsWiFi: 802.11b/g/n protocol, 2.4GhHz, supports Station mode, SoftAP mode, SoftAP+Station mode, hybrid modeBluetooth: BT 5.0Power consumption: Deep sleep power consumption is about 43 μ ARich on chip resources: 400KB SRAM, 384KB ROMRich interfaces: 1xI2C, 1xSPI, 2xUART, 11xGPIO (PWM), 4xADCSingle sided components, surface mount designClassic appearance, suitable for wearable devices and small projectsReliable security features: Encryption hardware accelerator supporting AES-128/256, hashing, RSA, HMAC, digital signature, and secure bootOn board LED blue light, GPIO8 pinSize: 22.52x18mmAttention:If external power supply is required, simply connect the external power supply+level to the 5V position and connect the GND to the negative pole. (Supports 3.3-6V power supply). Remember that when connecting to an external power source, USB cannot be connected, and only one can be selected between USB and external power supply.2. Please be careful not to short-circuit the positive and negative electrodes during welding, which may burn out the battery and equipment.Instructions for use:Enter download mode: Press and hold the BOOT button of ESP32C3, then press the RESET button, release the RESET button, and then release the BOOT button. At this point, ESP32C3 will enter download mode. (Every time you connect, you need to re-enter the download mode. Sometimes, if you press it once, the unstable port will disconnect, which can be determined by identifying the sound through the port.)Product List:1-10 X development board

• Payment must be received in 5 business days of sale closing.
• Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
• Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.

Shipping

• We maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you contact us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your concerns.

Refund

• All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can\'t take a refund.
• If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
• If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.